FMI LMF36-SC User manual

Brand: FMI

Model: LMF36-SC

Category: Fireplaces

Type: User manual

For more information, visit www.fmiproducts.com

WARNING: If the information in this manual is not

followed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

UNVENTED (VENT-FREE) GAS LOG HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

REMOTE CONTROL LOG SET AND BURNER SYSTEM MODELS

MF42INE, MF42IPE, MF48INE, MF48IPE, VFGT24NE, VFGT24PE,

VFGT30NE, VFGT30PE, VFGT36NE AND VFGT36PE

MF42 MODELS MAY BE USED WITH LMF36-SC AND LMF42-SC LOGS ONLY

MF48 MODELS MAY BE USED WITH LMF48-SC LOGS ONLY

VFGT24 MODELS MAY BE USED WITH GT24 LOGS ONLY

VFGT30 MODELS MAY BE USED WITH GT30 LOGS ONLY

VFGT36 MODELS MAY BE USED WITH GT36 LOGS ONLY

PFS

www.fmiproducts.com

125795-01B2

SAFETY

WARNING: Improper

installation, adjustment,

alteration, service or main-

tenance can cause injury

or property damage. Refer

to this manual for correct

installation and operation-

al procedures. For assis-

tance or additional infor-

mation consult a qualied

installer, service agency

or the gas supplier.

WARNING: This ap-

pliance is for installation

only in a solid-fuel burn-

ing masonry or UL127

factory-built replace or

in a listed ventless rebox

enclosure. It is design-cer-

tied for these installations

in accordance with ANSI

Z21.11.2. Exception: Do not

install this appliance in a

factory-built replace that

includes instructions stat-

ing it has not been tested

or should not be used with

unvented gas logs.

WARNING: This is an

unvented gas-red heat-

er. It uses air (oxygen)

from the room in which

it is installed. Provisions

for adequate combustion

and ventilation air must

be provided. Refer to Air

for Combustion and Ven-

tilation section on page 6

of this manual.

This appliance may be in-

stalled in an aftermarket,*

permanently located,

manufactured (mobile)

home, where not prohib-

ited by local codes.

This appliance is only for

use with the type of gas

indicated on the rating

plate. This appliance is

not convertible for use

with other gases.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

TABLE OF CONTENTS

Safety .................................................................. 2

Product Identication ........................................... 5

Local Codes......................................................... 5

Unpacking............................................................ 5

Product Features ................................................. 6

Air For Combustion and Ventilation ..................... 6

Installation ........................................................... 8

Operation ........................................................... 23

Inspecting Burners............................................. 29

Cleaning and Maintenance ................................ 29

Specications .................................................... 30

Wiring Diagram .................................................. 31

Troubleshooting ................................................. 32

Accessories ....................................................... 39

Parts .................................................................. 40

Replacement Parts ............................................ 43

Service Hints ..................................................... 43

Technical Service............................................... 43

Warranty ..............................................Back Cover

www.fmiproducts.com

125795-01B 3

WARNING: Do not allow fans

to blow directly into the replace.

Avoid any drafts that alter burner

ame patterns. Ceiling fans can

create drafts that alter burner

ame patterns. Altered burner

patterns can cause sooting.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects on the heater.

Heater base assembly becomes

very hot when running heater.

Keep children and adults away

from hot surface to avoid burns

or clothing ignition. Heater

will remain hot for a time after

shutdown. Allow surface to cool

before touching.

Carefully supervise young chil-

dren when they are in the room

with heater. When using the hand-

held remote accessory, keep se-

lector switch in the OFF position

to prevent children from turning

on burners with remote.

You must operate this heater

with the replace screen and

hood in place. Make sure re-

place screen and hood are in

place before running heater.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other am-

mable vapors and liquids.

WARNING: This product con-

tains and/or generates chemicals

known to the state of California

to cause cancer or birth defects

or other reproductive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, op-

erate or service this replace.

Improper use of this replace

can cause serious injury or

death from burns, re, explo-

sion, electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of

carbon monoxide poisoning resemble the u,

with headaches, dizziness or nausea. If you

have these signs, the replace may not be

working properly. Get fresh air at once! Have

replace serviced. Some people are more af-

fected by carbon monoxide than others. These

include pregnant women, people with heart or

lung disease or anemia, those under the inu-

ence of alcohol and those at high altitudes.

Natural and Propane/LP

gases are odorless. An

odor-making agent is added to these gases.

The odor helps you detect a gas leak. How-

ever, the odor added to the gas can fade. Gas

may be present even though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this replace.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use a

blower insert, heat exchanger

insert or other accessory not ap-

proved for use with this heater.

SAFETY

Continued

www.fmiproducts.com

125795-01B4

SAFETY

Continued

1. This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases.

2. Do not place propane/LP supply tank(s)

inside any structure. Locate propane/LP

supply tank(s) outdoors (propane/LP units

only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier’s instructions

• if you cannot reach your gas supplier,

call the re department

4. This heater shall not be installed in a

bedroom or bathroom.

5. Before installing in a solid fuel burning re-

place, the chimney ue and rebox must

be cleaned of soot, creosote, ashes and

loose paint by a qualied chimney cleaner.

Creosote will ignite if highly heated. A dirty

chimney ue may create and distribute

soot within the house. Inspect chimney

ue for damage. If damaged, repair ue

and rebox before operating heater.

6. Do not burn solid-fuel in a masonry or

UL127 factory-built replace in which a

vent-free room heater is installed.

7. If replace has glass doors, never operate

this heater with glass doors closed. If you

operate heater with doors closed, heat

buildup inside replace will cause glass to

burst. Make sure there are no obstructions

across openings of replace.

8. To prevent the creation of soot, follow the

instructions in Cleaning and Maintenance,

page 29.

9. Before using furniture polish, wax, carpet

cleaner or similar products, turn heater off. If

heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls and furniture.

10. This heater needs fresh, outside air ven-

tilation to run properly. This heater has an

Oxygen Depletion Sensing (ODS) safety

shutoff system. The ODS shuts down the

heater if enough fresh air is not available.

See Air for Combustion and Ventilation,

page 6. If heater keeps shutting off, see

Troubleshooting, page 32.

11. Do not run heater

• where ammable liquids or vapors are

used or stored

• under dusty conditions

12. Do not use this heater to cook food or burn

paper or other objects.

13. Do not use heater if any part has been ex-

posed to or under water. Immediately call

a qualied service technician to inspect

the room heater and to replace any part

of the control system and any gas control

which has been under water.

14. Do not operate heater if any log is broken.

Do not operate heater if a log is chipped

(dime-sized or larger).

15. Turn heater off and let cool before servic-

ing, installing or repairing. Only a qualied

service person should install, service or

repair heater.

16. Make sure the remote is set to the OFF

position when you are away from home

for long periods of time.

17. Remote heaters must not be connected

to any external electrical source.

18. Operating heater above elevations of

4,500 feet may cause pilot outage.

19. To prevent performance problems, do

not use propane/LP fuel tank of less than

100 lb. capacity (propane/LP units only).

20. Provide adequate clearances around air

openings.

www.fmiproducts.com

125795-01B 5

PRODUCT IDENTIFICATION

Figure 1 - Product Identication

LOCAL CODES

Glowing

Embers

Chassis

UNPACKING

CAUTION: Do not remove the

data plates from the grate as-

sembly. The data plates contain

important warranty and safety

information.

1. Remove logs and heater base assembly

from carton(s).

Note: Do not pick up heater base assem-

bly by burners. This could damage heater.

Always handle base assembly by grate.

2. Remove all protective packaging applied

to logs and heater for shipment.

3. Check heater for any shipping damage. If

heater is damaged call FMI PRODUCTS,

LLC at 1-866-328-4537 for replacement

parts before returning to dealer.

Install and use heater with care. Follow all

local codes. In the absence of local codes,

use the latest edition of The National Fuel

Gas Code, ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

State of Massachusetts: The installa-

tion must be made by a licensed plumber

or gas fitter in the Commonwealth of

Massachusetts.

Sellers of unvented propane or natural

gas-red supplemental room heaters shall

provide to each purchaser a copy of 527

CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for

bedroom and bathroom installation in the

Commonwealth of Massachusetts.

www.fmiproducts.com

125795-01B6

OPERATION

This heater is clean burning. It requires no

outside venting. There is no heat loss out a

vent or up a chimney. Heat is generated by

both realistic ames and glowing coals. This

heater is designed for vent-free operation

with ue damper closed. It has been tested

and approved to ANSI Z21.11.2 standard for

unvented heaters.

PRODUCT FEATURES

SAFETY DEVICE

This heater has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free

room heaters. The ODS/pilot shuts off the

heater if there is not enough fresh air.

ELECTRONIC IGNITION SYSTEM

This heater has an electronic ignitor to light

heater fuel supply.

AIR FOR COMBUSTION AND VENTILATION

WARNING: This heater shall

not be installed in a room or space

unless the required volume of

indoor combustion air is provided

by the method described in the

National Fuel Gas Code, ANSI

Z223.1/NFPA 54, the International

Fuel Gas Code, or applicable

local codes. Read the following

instructions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

Today’s homes are built more energy efcient

than ever. New materials, increased insulation

and new construction methods help reduce

heat loss in homes. Home owners weather

strip and caulk around windows and doors to

keep the cold air out and the warm air in. Dur-

ing heating months, home owners want their

homes as airtight as possible.

While it is good to make your home energy

efcient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning ap-

pliances need fresh air for proper combustion

and ventilation.

Exhaust fans, replaces, clothes dryers and

fuel burning appliances draw air from the house

to operate. You must provide adequate fresh

air for these appliances. This will insure proper

venting of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation.

All spaces in homes fall into one of the three

following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 6 through 8 will help

you classify your space and provide adequate

ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion

and ventilation. However, in buildings of un-

usually tight construction, you must provide

additional fresh air.

Unusually tight construction is dened as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6 x 10

-11

kg per pa-sec-m

) or

less with openings gasketed or sealed

and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and oors, between wall-ceiling joints,

between wall panels, at penetrations

for plumbing, electrical and gas lines

and at other openings.

If your home meets all of the three criteria

above, you must provide additional fresh air.

See Ventilation Air From Outdoors, page 8.

If your home does not meet all of the three

criteria above, proceed to Determining Fresh-

Air Flow For Heater Location, page 7.

www.fmiproducts.com

125795-01B 7

AIR FOR COMBUSTION AND VENTILATION

Continued

Conned and Unconned Space

The National Fuel Gas Code, ANSI Z223.1/

NFPA 54 denes a conned space as a space

whose volume is less than 50 cubic feet per

1,000 Btu/hr (4.8 m

per kw) of the aggregate

input rating of all appliances installed in that

space and an unconned space as a space

whose volume is not less than 50 cubic feet

per 1,000 Btu/hr (4.8 m

per kw) of the ag-

gregate input rating of all appliances installed

in that space. Rooms communicating directly

with the space in which the appliances are

installed*, through openings not furnished

with doors, are considered a part of the un-

conned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation

grills between them.

DETERMINING FRESH-AIR FLOW

FOR HEATER LOCATION

Determining if You Have a Conned or

Unconned Space

Use this work sheet to determine if you have

a conned or unconned space.

Space: Includes the room in which you will install

replace plus any adjoining rooms with door-

less passageways or ventilation grills between

the rooms.

1. Determine the volume of the space (length

x width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2560 cu. ft.

(volume of space)

If additional ventilation to adjoining room

is supplied with grills or openings, add the

volume of these rooms to the total volume

of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20

= 51,200 (maximum Btu/Hr the space can

support)

3. Add the Btu/Hr of all fuel burning appliances

in the space.

Vent-free replace __________ Btu/Hr

Gas water heater* __________ Btu/Hr

Gas furnace __________ Btu/Hr

Vented gas heater __________ Btu/Hr

Gas replace logs __________ Btu/Hr

Other gas appliances* + _________ Btu/Hr

Total = _________ Btu/Hr

* Do not include direct-vent gas appliances.

Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

Example:

Gas water heater __________ Btu/Hr

Vent-free replace + _________ Btu/Hr

Total = _________ Btu/Hr

4. Compare the maximum Btu/Hr the space

can support with the actual amount of Btu/

Hr used.

______Btu/Hr (maximum the space can

support)

______Btu/Hr (actual amount used)

Example: 51,200 Btu/Hr (maximum the

space can support)

73,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the above example is a conned

space because the actual Btu/Hr used is more

than the maximum Btu/Hr the space can sup-

port. You must provide additional fresh air. Your

options are as follows:

A. Rework worksheet, adding the space of an

adjoining room. If the extra space provides

an unconned space, remove door to adjoin-

ing room or add ventilation grills between

rooms. See Ventilation Air From Inside

Building, page 8.

B. Vent room directly to the outdoors. See

Ventilation Air From Outdoors, page 8.

C. Install a lower Btu/Hr replace, if lower Btu/

Hr size makes room unconned.

If the actual Btu/Hr used is less than the maxi-

mum Btu/Hr the space can support, the space is

an unconned space. You will need no additional

fresh air ventilation.

WARNING: If the area in which

the heater may be operated does

not meet the required volume for

indoor combustion air, combus-

tion and ventilation air shall be

provided by one of the methods

described in the National Fuel

Gas Code, ANSI Z223.1/NFPA 54,

the International Fuel Gas Code,

or applicable local codes.

40,000

33,000

73,000

www.fmiproducts.com

125795-01B8

AIR FOR COMBUSTION AND VENTILATION

Continued

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two perma-

nent openings: one within 12" of the ceiling

and one within 12" of the oor. Connect these

items directly to the outdoors or spaces open

to the outdoors. These spaces include attics

and crawl spaces. Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for

Combustion and Ventilation for required size

of ventilation grills or ducts.

IMPORTANT: Do not provide openings for

inlet or outlet air into attic if attic has a thermo-

stat-controlled power vent. Heated air entering

the attic will activate the power vent.

Figure 3 - Ventilation Air from Outdoors

Outlet

Air

Ventilated

Attic

Outlet

Inlet

Air

Inlet Air

Ventilated

Crawl Space

Crawl

Space

To Attic

INSTALLATION

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining

unconned space. When ventilating to an

adjoining unconned space, you must provide

two permanent openings: one within 12" of the

ceiling and one within 12" of the oor on the

wall connecting the two spaces (see options

1 and 2, Figure 2). You can also remove door

into adjoining room (see option 3, Figure 2).

Follow the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, Air for Combustion and

Ventilation for required size of ventilation

grills or ducts.

Figure 2 - Ventilation Air from Inside Building

Remove

Door into

Adjoining

Room,

Option

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills Into

Adjoining

Room,

Option 1

12"

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualied ser-

vice person must install heater.

Follow all local codes.

WARNING: Seal any fresh

air vents or ash clean-out doors

located on oor or wall of re-

place. If not, drafting may cause

pilot outage or sooting. Use a

heat-resistant sealant. Do not

seal chimney ue damper.

www.fmiproducts.com

125795-01B 9

LOG SIZING REQUIREMENTS

Log

Size

Minimum Firebox Size

Height Depth

Front

Width

Rear*

Width

LMF36-SC 29" 15.5" 32.5" 22.75"

LMF42-SC 29" 15.5" 39" 26.75"

LMF48-SC 29'' 20'' 47'' 33''

GT24 29'' 15.5'' 32.5'' 22.75''

GT30 29'' 15.5'' 39'' 26.75''

GT36 29'' 20'' 47'' 33''

* Also approved for use in Vantage Hearth Model

VFB42, VTFB42 and VUM42 replaces.

WARNING: Before installing

in a solid fuel burning replace,

the chimney ue and rebox

must be cleaned of soot, creo-

sote, ashes and loose paint by

a qualified chimney cleaner.

Creosote will ignite if highly

heated. A dirty chimney ue may

create and distribute soot within

the house. Inspect chimney and

rebox ue for damage. If dam-

aged, repair ue and rebox

before operating heater.

WARNING: Never install the

heater

• in a bedroom or bathroom

• in a recreational vehicle

•

where curtains, furniture, cloth-

ing or other ammable objects

are less than 36" from front, 42"

from top of heater; for side clear-

ances see Figure 4, page 10

• in high trafc areas

• in windy or drafty areas

CAUTION: This heater creates

warm air currents. These currents

move heat to wall surfaces next

to heater. Installing heater next

to vinyl or cloth wall coverings or

operating heater where impurities

(such as, but not limited to, to-

bacco smoke, aromatic candles,

cleaning uids, oil or kerosene

lamps, etc.) in the air exist, may

discolor walls or cause odors.

IMPORTANT: Vent-free heaters add moisture

to the air. Although this is benecial, installing

heater in rooms without enough ventilation

air may cause mildew to form from too much

moisture. See Air for Combustion and Ventila-

tion, page 6.

CHECK GAS TYPE

Use the correct type of gas (natural or propane/

LP). If your gas supply is not the correct gas

type, do not install heater. Call dealer where

you bought heater for proper type heater.

WARNING: This appliance is

equipped for either natural gas

or propane/LP gas but not both.

Gas type is indicated on the rat-

ing plate. Field conversion is not

permitted.

INSTALLATION AND CLEARANCES

FOR VENT-FREE OPERATION

WARNING: Maintain the

minimum clearances. If you can,

provide greater clearances from

oor, ceiling and adjoining wall.

MINIMUM FIREPLACE CLEARANCE TO

COMBUSTIBLE MATERIALS

Side Wall 16", Ceiling 42"

Floor 5", Front: 36"

Carefully follow the instructions below. This

will ensure safe installation into a masonry,

UL127-listed manufactured replace or listed

vent-free rebox.

Minimum Clearances For Side Combustible

Material, Side Wall and Ceiling

A. Clearances from the side of the replace

cabinet to any combustible material and

wall should follow diagram in Figure 4,

page 10.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material

and protrudes 3

/2" from the wall. This

combustible material must be 4" from the

side of the replace cabinet (see Figure

4, page 10).

INSTALLATION

Continued

www.fmiproducts.com

125795-01B10

INSTALLATION

Continued

Note: When installing your gas logs into

a manufactured rebox, follow rebox

manufacturer’s instructions for minimum

clearances to combustible materials.

B. Clearances from the top of the replace

opening to the ceiling should not be less

than 42".

Heat Resistant

Material

(A)

Figure 5 - Heat Resistant Material (Slate,

Marble, Tile, etc.) Above Fireplace

Noncombustible

Material Distance

(A)

Requirements for

Safe Installation

2" or more Noncombustible mate-

rial OK.

Between 8" and 12"

Install replace hood

accessory (GA6050 or

GA6053 see Accesso-

ries, page 39).

Less than 8"

Noncombustible mate-

rial must be extended

to at least 8". See

Between 8" and 12",

above. If you cannot

extend material, you

must operate heater

with ue damper open.

Figure 4 - Minimum Clearance for

Combustible to Wall

*Minimum 16" from Side Wall

Example

Minimum Noncombustible Material

Clearances

If Not Using Mantel

Note: If using a mantel proceed to If Using

Mantel. If not using a mantel, follow these

instructions.

You must have noncombustible material(s)

above the replace opening. Noncombustible

materials (such as slate, marble, tile, etc.) must

be at least 1/2" thick. With sheet metal, you

must have noncombustible material behind

it. Noncombustible material must extend at

least 8" up (for all models). If noncombustible

material is less than 12", you must install the

replace hood accessory (24" and 30" Models

Only). See Figure 5 for minimum clearances.

If Using Mantel

You must have noncombustible material(s)

above the replace opening. Noncombustible

materials (such as slate, marble, tile, etc.)

must be at least 1/2" thick. With sheet metal,

you must have noncombustible material be-

hind it. Noncombustible material must extend

at least 8" up (for all models). If noncom-

bustible material is less than 12", you must

install the replace hood accessory. Even if

noncombustible material is more than 12",

you may need the hood accessory to deect

heat away from your mantel shelf. See Figure

5 and Figures 6 and 7, page 11, for minimum

clearances.

www.fmiproducts.com

125795-01B 11

INSTALLATION

Continued

MANTEL CLEARANCES

In addition to meeting noncombustible mate-

rial clearances, you must also meet required

clearances between replace opening and

mantel shelf. If you do not meet the clearances

listed below, you will need a hood.

Determining Minimum Mantel Clearance

If you meet minimum clearance between

mantel shelf and top of replace opening, a

hood is not required (see Figure 6).

Figure 6 - Minimum Mantel Clearances

Without Using Hood

14"

Min.

Combustible

Material

Noncombustible Material

Figure 8 - Minimum Fireplace Clearances

If Installed at Floor Level

Figure 7 - Minimum Mantel Clearances

When Using Hood

Minimum Non-

Combustible

Material

Minimum Non-

Combustible

Material Height

Distances to

Underside of

Mantel

Top of Fireplace

Opening

Underside of

Mantel Shelf

12"

(A)

18" 20" 22" 24"

All minimum

distances are

in inches

10"

Mantel Shelf

Minimum

Noncombustible

Material

Min.

12" 15" 18" 20"

10"

12"

Distances to

Underside of

Mantel

Hood (GA6050

or GA6053)

Top of

Fireplace

Opening

Underside

of Mantel

Shelf

Mantel Shelf

Hearth

Min.

Combustible

Material

Figure 9 - Minimum Fireplace Clearances

Above Combustible Flooring

NOTICE: Surface temperatures

of adjacent walls and mantels be-

come hot during operation. Walls

and mantels above the rebox

may become hot to the touch.

If installed properly, these tem-

peratures meet the requirement

of the national product standard.

Follow all minimum clearances

shown in this manual.

NOTICE: If your installation does

not meet the minimum clear-

ances shown, you must do one

of the following:

• operate the logs only with the

ue damper open

• raise the mantel to an accept-

able height

• remove the mantel

FLOOR CLEARANCES

A. If installing appliance on the oor level,

you must maintain the minimum distance

of 14" to combustibles (see Figure 8).

B. If combustible materials are less than 14"

to the replace, you must install appliance

at least 5" above the combustible ooring

(see Figure 9).

Determining Minimum Mantel Clearance

When Using a Hood

If minimum clearances in Figure 6, are not

met, you must have a hood. When using a

hood there are still certain minimum mantel

clearances required. Follow minimum clear-

ances shown in Figure 7, when using hood.

www.fmiproducts.com

125795-01B12

INSTALLATION

Continued

INSTALLING HEATER BASE

ASSEMBLY

WARNING: You must secure

this heater to replace oor. If

not, heater will move when you

adjust controls. Moving heater

may cause a gas leak.

WARNING: If installing in a

sunken replace, special care

is needed. You must raise the

replace oor to allow access to

heater control panel. This will in-

sure adequate air ow and guard

against sooting and controls

being damaged. Raise replace

oor with noncombustible mate-

rial. Make sure material is secure.

CAUTION: Do not pick up

heater base assembly by burn-

ers. This could damage heater.

Only handle base assembly by

grates.

IMPORTANT: Make sure the heater burners

are level.

Installation Items Needed

• hardware package (provided with heater)

• approved exible gas hose and ttings

provided (if allowed by local codes)

• sealant (resistant to propane/LP gas, not

provided)

• electric drill with 3/16” masonry drill bit

Note: Install optional MRC Series receiver

and hand-held remote control kit (see Ac-

cessories, page 39) before installing gas log

heater. See installation instructions included

with the kit.

1. Apply pipe joint sealant lightly to male

threads of the 3/8 NPT side of gas tting

elbow (provided) and connect to inlet

side of gas control. Remove gas tting

from exible gas hose (provided) before

connecting to elbow (see Figure 10).

2. Position heater base assembly in re-

place.

3. Mark screw locations through holes in

front panel of base (see Figure 11). If

installing in a brick-bottom replace, mark

screw locations in mortar joint of bricks.

4. Remove heater base from replace.

5. Drill holes at marked locations using 3/16"

drill bit.

6. Attach base, through holes in back side pan-

els of base, to replace oor using masonry

screws provided in hardware package (see

Figure 11).

7. Connect to gas supply. See Connecting

To Gas Supply, page 13.

Figure 10 - Attaching Flexible Gas Hose

to Heater Gas Regulator

Figure 11 - Attaching Base to Fireplace

Floor

Masonry Screw

Heater Gas

Regulator

Flexible Gas Hose (Provided

with Models, Install if

allowed by local codes)

www.fmiproducts.com

125795-01B 13

INSTALLATION

Continued

CONNECTING TO GAS SUPPLY

WARNING: This appliance

requires a 3/8" NPT (National

Pipe Thread) inlet connection to

the pressure regulator.

WARNING: A qualied service

person must connect heater to

gas supply. Follow all local codes.

CAUTION: Never connect

propane/LP replace directly

to the propane/LP supply. This

heater requires an external regu-

lator (not supplied). Install the

external regulator between the

heater and propane/LP supply.

WARNING: Never connect

natural gas replace to private

(non-utility) gas wells. This

gas is commonly known as

wellhead gas.

Installation Items Needed

Before installing heater, make sure you have

the items listed below.

• external regulator (supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection *

• sediment trap

• tee joint

• pipe wrench

• approved exible gas line with gas connec-

tor (if allowed by local codes) (not provided)

* An equipment shutoff valve with 1/8" NPT

tap is an acceptable alternative to test gauge

connection. Purchase the optional equipment

shutoff valve from your dealer.

For propane/LP units, the installer must

supply an external regulator. The external

regulator will reduce incoming gas pressure.

You must reduce incoming gas pressure to

between 11" and 14" of water. If you do not re-

duce incoming gas pressure, heater regulator

damage could occur. Install external regulator

with the vent pointing down as shown in Figure

12, page 14. Pointing the vent down protects

it from freezing rain or sleet.

CAUTION: Use only new,

black iron or steel pipe. In-

ternally-tinned copper tubing

may be used in certain areas.

Check your local codes. Use

pipe of 1/2" diameter or greater

to allow proper gas volume to

heater. If pipe is too small, undue

loss of volume will occur.

Installation must include an equipment shutoff

valve, union and plugged 1/8" NPT tap. Locate

NPT tap within reach for test gauge hook up.

NPT tap must be upstream from heater (see

Figure 13, page 14).

IMPORTANT: Install equipment shutoff valve

in an accessible location. The equipment

shutoff valve is for turning on or shutting off

the gas to the appliance.

Check your building codes for any special

requirements for locating equipment shutoff

valve to replaces.

Apply pipe joint sealant lightly to male NPT

threads. This will prevent excess sealant from

going into pipe. Excess sealant in pipe could

result in clogged heater valves.

WARNING: Use pipe joint

sealant that is resistant to liquid

petroleum (LP) gas.

Propane/LP

Supply Tank

External

Regulator

with Vent

Pointing

Down

Figure 12 - External Regulator With Vent

Pointing Down

www.fmiproducts.com

125795-01B14

INSTALLATION

Continued

We recommend that you install a sediment

trap in supply line as shown in Figure 13.

Locate sediment trap where it is within reach

for cleaning. Install in piping system between

fuel supply and heater. Locate sediment trap

where trapped matter is not likely to freeze.

A sediment trap traps moisture and contami-

nants. This keeps them from going into heater

controls. If sediment trap is not installed or is

installed wrong, heater may not run properly.

CAUTION: Avoid damage to

gas control. Hold gas control

with wrench when connecting

it to gas piping and/or ttings.

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping

and connections, internal and

external to unit, for leaks after

installing or servicing. Correct

all leaks at once.

* Purchase the optional equipment shutoff

valve from your dealer.

**Minimum inlet pressure for purpose of input

adjustment.

Figure 13 - Gas Connection

WARNING: Never use an open

ame to check for a leak. Apply a

noncorrosive leak detection uid

to all joints. Bubbles forming show

a leak. Correct all leaks at once.

CAUTION: Make sure exter-

nal regulator has been installed

between propane/LP supply and

heater. See guidelines under Con-

necting to Gas Supply, page 13.

PRESSURE TESTING GAS SUPPLY

PIPING SYSTEM

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

1. Disconnect appliance with its appliance

main gas valve (control valve) and equip-

ment shutoff valve from gas supply piping

system. Pressures in excess of 1/2 psig

will damage heater regulator.

2. Cap off open end of gas pipe where equip-

ment shutoff valve was connected.

3. Pressurize supply piping system by either

opening propane/LP supply tank valve

for propane/LP gas or opening main gas

valve located on or near gas meter for

natural gas or using compressed air.

4. Check all joints of gas supply piping system.

Apply noncorrosive leak detection uid to

all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff

valve to gas supply. Check reconnected

ttings for leaks.

Test Pressures Equal To or Less Than 1/2

PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Fig-

ure 15).

2. Pressurize supply piping system by either

opening propane/LP supply tank valve

for propane/LP gas or opening main gas

valve located on or near gas meter for

natural gas or using compressed air.

3. Check all joints from gas meter to equip-

ment shutoff valve for natural gas or pro-

pane/LP supply to equipment shutoff valve

for propane/LP (see Figure 15 or Figure

16). Apply noncorrosive leak detection uid

to all joints. Bubbles forming show a leak.

4. Correct all leaks at once.

Tee Cap Pipe

Joint Nipple

3" Minimum

Gas

Regulator

PROPANE/LP From

External Regulator

(11" W.C.** to 14" W.C.

Pressure)

NATURAL From Gas

Meter (5" W.C.**

to 10.5" W.C.

Pressure)

Equipment Shutoff

Valve With 1/8"

NPT Tap*

Approved

Flexible Gas

Hose (if allowed

by local codes)

Sediment Trap

www.fmiproducts.com

125795-01B 15

INSTALLATION

Continued

PRESSURE TESTING HEATER GAS

CONNECTIONS

Open equipment shutoff valve (see Figure 14).

2. Open main gas valve located on or near

gas meter for natural gas or open pro-

pane/LP supply tank valve.

3. Make sure control knob of heater is in the

OFF position.

4. Check all joints from gas meter to equip-

ment shutoff valve for natural gas or pro-

pane/LP supply to equipment shutoff valve

for propane/LP (see Figure 15, or Figure

16). Apply noncorrosive leak detection uid

to all joints. Bubbles forming show a leak.

5. Correct all leaks at once.

6. Light heater (see Operation, page 23).

Check all other internal joints for leaks.

Turn off heater (see To Turn Off Gas to

Appliance, page 23 for Remote models.

Figure 14 - Equipment Shutoff Valve

Open

Closed

Equipment

Shutoff

Valve

Figure 15 - Checking Gas Joints

(Propane/LP Only)

Control Valve

Location

Propane/LP

Supply Tank

Equipment Shutoff Valve

Gas Meter

Figure 16 - Checking Gas Joints (Natural

Gas Only)

Control Valve

Location

Equipment

Shutoff Valve

POWER SUPPLY AND BATTERY

INSTALLATION

It is helpful to have a ashlight so you can

see the connections as described below. Lo-

cate the battery power supply. It is the black

box with the red and black wires. Locate the

control module (see Figure 17). Connect the

battery power supply to the control module

by plugging the battery power supply to the

mating receptacle on the control module. The

receptacle is located on the side of the black

control module next to the word “SUPPLY”

which is molded in the control module’s black

housing (see Figure 17). Be certain to push

the plug fully into the receptacle. Install bat-

teries in the battery power supply and hand

held remote control.

Figure 17 - Control Module

S1 Button

Connect Battery Plug Here

TOUCH PAD INSTALLATION

Locate the touch pad wire harness and the

touch pad control (see Figure 18, page 16).

They are shipped from the factory in the clear

plastic bag with your owner’s manual. Con-

nect the black plastic connectors together as

shown in Figure 19, page 16. Connect the

remaining end with the white plastic connector

to the control module in the socket marked

TOUCH LED (see Figure 20, page 16).

NOTE: The touch pad includes a red LED

display light. If the LED remains on, the black

plug is connected upside down. You must

unplug the touch pad control from the touch

pad wire harness, turn over, and reconnect.

www.fmiproducts.com

125795-01B16

INSTALLATION

Continued

Touch Pad Wire Harness

Touch Pad Control

Figure 18 - Touch Pad Wire Harness and

Touch Pad Control

RE-PAIRING

IMPORTANT! This appliance is shipped

with the remote control and control module

(receiver) paired. However, if more than one

Copreci brand electronic ignition system is

to be used within a home or showroom, all

but one appliance must have the remote

control and control module re-paired in order

for each appliance to operate on a unique

frequency. For multiple appliances, on all but

one follow the instructions under Re-Pairing

on page 16 before moving to Installing Logs

on page 18. For single appliance installations,

skip the RE-PARING section and proceed to

Installing Logs.

It is helpful to have a ashlight so you can see

the connections as described below. Before

Figure 19 - Touch Pad Control Cable

Figure 20 - Connecting end of Touch Pad

Cable

proceeding, locate the yellow/orange S1

button on the control module. You will need

to access this button during the re-pairing

procedure and only have 20 seconds to press

and release it. A small nail or ink pen will also

be useful to press this button (see Figure 17,

page 15).

Press and hold the “Off” button on the

remote control for 40 seconds. During this

time, the screen will go blank, this is normal.

See Figure 21.

Figure 21 - Main Screen

OFF

Button

Fri 20:45

Lock MenuOn

OFF

°F

Configuration

Select

Back

Off

Yes

0.5°C

Thermostat

Programming

Gap Temp

Fri 22:04

Pairing

Figure 22 - Conguration Menu

SELECT

Button

Configuration

Select

Back

Off

Yes

0.5°C

Thermostat

Programming

Gap Temp

Fri 22:04

Pairing

Configuration

Change

Back

Yes

0.5°C

Thermostat

Programming

Gap Temp

Fri 21:47

Off

Pairing

After 40 seconds, the conguration menu

appears (see Figure 22). With ''Pairing'' high-

lighted press the middle ''select'' button. ''Off''

becomes highlighted (see Figures 22 and 23).

www.fmiproducts.com

125795-01B 17

INSTALLATION

Continued

Figure 23 - Off Highlighted

Configuration

Select

Back

Off

Yes

0.5°C

Thermostat

Programming

Gap Temp

Fri 22:04

Pairing

Configuration

Change

Back

Yes

0.5°C

Thermostat

Programming

Gap Temp

Fri 21:47

Off

Pairing

IMPORTANT! Be prepared to press the S1

button as noted in the beginning of this sec-

tion. After the next step, you have only 20

seconds to push (press and release) the S1

button (yellow/orange) in the control module

(see Figure 17, page 15).

NOTE: The control module may be turned dif-

ferently than shown in this gure. Look for the

matching text on the control module to help

locate the small yellow / orange S1.

Figure 24 - Change OFF to ON

Configuration

Change

Back

Yes

0.5°C

Thermostat

Programming

Gap Temp

Fri 22:04

Pairing

Change

Button

Configuration

Change

Back

Yes

0.5°C

Thermostat

Programming

Gap Temp

Fri 22:05

Off

Pairing

Configuration

Select

Back

Off

Yes

0.5°C

Thermostat

Programming

Gap Temp

Fri 22:05

Pairing

Figure 25 - Signal Bars

Figure 26 - Back and Middle Buttons

Configuration

Change

Back

Yes

0.5°C

Thermostat

Programming

Gap Temp

Fri 22:05

Off

Pairing

Configuration

Select

Back

Off

Yes

0.5°C

Thermostat

Programming

Gap Temp

Fri 22:05

Pairing

Back

Button

Middle

Button

Press the left "Change" button and "Off" becomes

"On" (see Figure 24, above). Press the S1 but-

ton to re-pair the remote to the control module.

Once this operation is done, you will hear one

beep in the control module and the congura-

tion menu will show signal bars: (see

Figure 25). If you do not hear the beep and then

Press the “Back” button once to return the

highlighted selection to “Pairing”. Press the

“Middle” button and release. The indication on

the “Pairing” will become “Off” (see Figure 26).

The re-pairing is over. To return to the main

screen, press the “Back” button until you get

to the main screen. The main screen is shown

in Figure 21, page 16.

see signal bars within 30 seconds of hearing

the beep, then the repairing process was not

completed successfully. If this occurs, remove

the batteries from the remote control, wait 3

minutes, and restart the re-pairing process. If

you see signal bars, then the remote control

has paired properly. Go to the next step.

www.fmiproducts.com

125795-01B18

INSTALLATION

Continued

CAUTION: After installa-

tion and periodically thereafter,

check to ensure that no ame

comes in contact with any log.

With heater set to Hi, check to

see if ames contact any log. If

so, reposition logs according to

log installation instructions in

this manual. Flames contacting

logs will create soot.

LOG PLACEMENT

It is very important to install these logs exactly

as instructed. Do not modify logs. Only use

logs supplied with heater or for MF models,

as identied for use with the heater as shown

in Figure 27.

Note: Each log includes an identifying number

cast in the log. Look at each log when plac-

ing them on the burner system to be certain

it is correct.

Note: For additional information, go to

www.fmiproducts.com and click on the

technical Support tab for access to log

placement videos.

Figure 27 - MF Series Burner System-

Log Compatibility Chart

INSTALLING LOGS, EMBERS AND

LAVA ROCK

WARNING: Failure to position

the parts in accordance with these

diagrams or failure to use only

parts specically approved with

this heater may result in property

damage or personal injury.

MF SERIES BURNER SYSTEM-LOG

COMPATIBILITY CHART

1. Find the right front log (LMF36-SC and

VFGT24 inch models: D-061 or LMF42-

SC and VFGT30 inch models: D-019 or

LMF48-SC and VFGT36 inch models:

D-027). See Figures 28, 28A, 28B, and

28C for reference. The log has a rectan-

gular shape on the bottom that ts against

the lip on the black metal base, the square

grate, and the round tube burner. Slide the

Figure 28 - Installing Right Front Log

Figure 28A - Installing Right Front Log,

Top View

Burner

Tube

Grate Finger

Right Front Log

(D061, D-019 or D027)

Round Tube

Burner

Grate Finger

Figure 28B - Installing Right Front Log,

Top View

Burner Tube

Square Grate

Burner System Model

Refractory Concrete

Logs For Use With This

Burner System

MF42INE,MF42IPE, LMF36-SC

LMF42-SC

MF48INE, MF48IPE,

LMF48-SC

www.fmiproducts.com

125795-01B 19

INSTALLATION

Continued

2. Find the back left log (LMF36-SC and

VFGT24 inch models: D-060 or LMF42-

SC and VFGT30 inch models: D-018 or

LMF48-SC and VFGT36 inch models:

D-026). See Figures 29, 29A, and 29B.

Figure 29A shows how the log must t

against the end of the burner. Figure 29B

shows how the notch in log ts against the

vertical portion of the burner tube. Place

this log on the base assembly by inserting

it from the left side as shown in Figure 19.

You will need to twist the log slightly to get

it to t against the burners properly. It will

rest even with the back edge of the pan.

Figure 28C - Installing Right Front Log,

Side View

Figure 29 - Installing Back Left Log

Back Left Log (D-060,

D-018 or D026)

Flat Part of Log

Log Notch

Burner Tube

Figure 29A - Installing Back Left Log

Figure 29B - Installing Back Left Log

(D-018) Rear View

Burner

Tube

Log

Notch

Vertical Portion of Burner Tube

3. Find the front left log (LMF36-SC and

VFGT24 inch models: D-059 or LMF42-

SC and VTGF30 inch models: D-017 or

LMF48-SC and VFGT36 inch models:

D-025). See Figures 30, 30A, and 30B.

The log has a rectangular stand off on

the bottom that ts against the lip on the

black metal base as shown in gure 30A.

The bottom of this log has a slot that ts

over the second bar on the grate as shown

in Figure 30B, page 20. Place the log on

the base assembly as shown in gures.

Figure 30 - Installing Front Left Log

Front Left Log (D-059,

D-017 or D025)

Figure 30A - Installing Front Left Log

Side View

Grate Fingers

www.fmiproducts.com

125795-01B20

INSTALLATION

Continued

4. Find the charred log (D-020). See Figures

31, 31A, and 31B. The log has a slot in the

bottom that ts over the square grate and

rests against the burner tube as shown in

Figure 31. Place this log on the base as

shown in gures.

Figure 30B - Installing Front Left Log

Grate Finger

Log Slot

Charred

Log

Log Notch

Right Front Log

Figure 31 - Installing Charred Log

Figure 31A - Installing Charred Log Top

View

Figure 31B - Installing Charred Log Top

Side View

Square Grate

Log Notch

5. Find the middle split log (LMF36-SC and

VFGT24 inch models: D-063 or LMF42-

SC and VFGT30 inch models: D-021 or

LMF48-SC and VTGF36 inch models:

D-028). See Figures 32 and 32A. The split

side of the log faces forward. The log has

a notch that ts around the burner tube on

the right side. The left side of the burner

tube ts into the notch on the back side of

this log. The log is placed properly when

it sits parallel to the tube burner and the

square peg is pointing up. See gures

for reference.

Figure 32 - Installing Middle Split Log

(D-021)

Middle Split Log (D-063,

D-021 or D028)

Square Peg

Figure 32A - Installing Middle Split Log

Rear Top Side View

Log Notch

Burner Tube

Page is loading ...

FMI LMF36-SC User manual

Brand: FMI

Model: LMF36-SC

Category: Fireplaces

Type: User manual

Download PDF

report

FMI LMF36-SC User manual

FMI LMF36-SC User manual

Related papers

Other documents