Samsung 4 channel DVR User manual

4 CHANNEL DVR

User Manual

SDE-3001/3003

Copyright

Trademark

is the registered logo of Samsung Techwin Co., Ltd.

The name of this product is the registered trademark of Samsung Techwin Co., Ltd.

Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced,

distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the

right to change the contents of this document without prior notice.

Warranty

If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the problem for free of charge.

The warranty period is 3 years. However, the followings are excluded:

• Data loss due to a damaged hard disk

• If the system behaves abnormally because you run a program irrelevant to the system operation.

• Data loss due to virus infection

• Deteriorated performance or natural worn-out in process of time

• Sensory phenomenon that does not affect the performance or quality of the product (ex: working noise).



Design and specifications are subject to change without prior notice.



The default password can be exposed to a hacking thread so it is recommended to change the password after installing the

product.

Note that the security and other related issues caused by the unchanged password shall be responsible for the user.

4 Channel DVR

User Manual

English _3

 OVERVIEW

IMPORTANT SAFETY INSTRUCTIONS

Read these operating instructions carefully before using the unit.

Follow all the safety instructions listed below.

Keep these operating instructions handy for future reference.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has

two blades with one wider than the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided for your safety. if the provided

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury from

tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

overview

4_ overview

overview

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within

this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation

instructions.

WARNING

1. Be sure to use only the standard adapter that is specified in the specification sheet.

Using any other adapter could cause fire, electrical shock, or damage to the product.

2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or

damage to the product.

3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat

generation or fire.

4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.

6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on

top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately

disconnect the power source and contact the service center. Continued use in such a condition may cause fire

or electric shock.

9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this

product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted

repair.)

10.

When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

11. Do not expose the product to the direct airflow from an air conditioner.

Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between

internal and external of the dome camera.

12. If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with

silicon, so that the external air can not flow inside the housing.

Otherwise, external high, humid air may flow inside the housing, pooling moisture or vapor inside the product

due to a difference between internal and external temperature.

English _5

 OVERVIEW

BEFORE START

This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection

to other equipment, menu setup, etc.

You have to keep in mind the following notices :

• SAMSUNG retains the copyright on this manual.

• This manual cannot be copied without SAMSUNG’s prior written approval.

• We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of

instructions mentioned in this manual.

• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be

removed from the unit.

• Before installing an additional HDD or connecting an external storage device (USB memory or USB HDD) to this

DVR, check the compatibility. Consult your provider for the compatibility list.

Warning

❖ Battery

It is essential that when changing the battery in the unit, the replacement battery must be of the same type

otherwise there may be a possibility of an explosion.

The following are the specifications of the battery you are using now.

• Normal voltage : 3V

• Normal capacity : 170mAh

• Continuous standard load : 0.2mA

• Operating temperature : -20°C ~ +85°C

(-4°F ~ +185°F)

J



Connect the power cord into a grounded outlet.



The Mains plug is used as a disconnect device and shall stay readily operable at any time.



Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

❖ System Shutdown

Turning off the power while the product is in operation, or undertaking improper actions may cause damage

or malfunction to the hard drive or the product.

Please turn off the power using the Power button on the front of your DVR.

After selecting <OK> in the pop-up menu, you can pull off the power cord.

You may want to install a UPS system for safe operation in order to prevent damage caused by an

unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)

❖ Operating Temperature

The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).

This product may not work properly if you run right after a long period of storage at a temperature below the

guaranteed one.

Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand

at room temperature for a period.

Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).

Likewise, the hard drive may not work at a temperature below the guaranteed one.

CALIFORNIA USA ONLY

This Perchlorate warning applies only to primary CR (Manganese Dioxide)

Lithium coin cells in the product sold or distributed ONLY in California USA.

“Perchlorate Material - special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.”

6_ overview

overview

CONTENTS

OVERVIEW

3

3 Important Safety Instructions

5 Before Start

8 Features

10 Part Names and Functions

(Front)

11 Part Names and Functions (Rear)

12 Remote Control

CONNECTING WITH

OTHER DEVICE

13

13 Installation

13 Checking the installation environment

14 Connecting the Video, Audio, and Monitor

14 Connecting the USB

15 Connecting the Camera

18 Connecting the Alarm Input/Output

19 Connecting the Network

LIVE

21

21 Getting Started

23 Live Screen Configuration

27 Live Mode

29 Spot Out

29 Zoom

30 Audio ON/OFF

30 Freeze

30 Event Monitoring

USING THE DVR

32

32 System Setup

42 Setting the Device

48 Setting the Recording

51 Setting the Event

54 Backup

55 Network Configuration

English _7

 OVERVIEW

SEARCH & PLAY

62

62 Search

65 Playback

WEB VIEWER

67

67 Introducing Web Viewer

68 Connecting Web Viewer

69 Using Live Viewer

73 Using Search Viewer

77 Viewer Setup

87 About

87 Mobile Viewer

BACKUP VIEWER

88

88 SEC Backup Viewer

APPENDIX

90

90 Product Specification (Camera)

92 Product Specification

94 Default Setting

97 Troubleshooting

99 Open Source License Report on the Product

8_ overview

overview

FEATURES

The DVR employs H.264 video encoding for 4 channel inputs and audio encoding for 4 channels while simultaneously

supports hard disc recording and playback.

These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video

and audio data.

• Provides a convenient User Interface

• 4 CH Composite Input Connectors

• Supports CIF(S)/2CIF(M)/4CIF(L) recording formats

• With the network specific codec, network transfer enabled regardless of the recording conditions

• De-interlacing processor for better picture quality

• Display of HDD information and status by using HDD SMART

• Hard Disk overwrite function

• Mass storage hard disk backup through high-speed USB 2.0

• Simultaneous Record and Playback of 4 channel video data

• Various Search Modes (Search by Time, Event, Backup and Motion Detection)

• Various Recording Modes (Time Lapse, Event, Scheduled Recording)

• Alarm Interface

• Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer

English _9

 OVERVIEW

Standards Approvals

M



This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Package Contents

Please unwrap the product, and place the product on a flat place or in the place to be installed.

Please check the following contents are included in addition to the main unit.

POWER

REC

DIGITAL VIDEO RECORDER

DVR Adapter / Power Cable Mouse

Remote Control / Battery (AAA x 2)

SEB-1005R (4EA)

Model : SDE-3003

SEB-1007R (4EA)

Model : SDE-3001

SEB-1005R (Bracket 4EA, Screws 12EA)

Model : SDE-3003

SEB-1007R (Bracket 4EA, Screws 12EA)

Model : SDE-3001

Camera Cables(4EA), 18.3m (60ft) /

Network Cables

Network Viewer Software

User Manual CD,

Quick Connect Program CD

Quick Guide

10_ overview

overview

PART NAMES AND FUNCTIONS (FRONT)

Part Names Functions



USB Port Connects the USB devices.

b

Remote Control

Receiver

Input the remote control signal.

c

LED Indicator

Power LED : Displays the power ON/OFF status.

REC : Lights on when recording is in progress.

POWER

REC

DIGITAL VIDEO RECORDER

 cb

English _11

 OVERVIEW

PART NAMES AND FUNCTIONS (REAR)

Part Names Functions



CAMERA IN Video Signal input ports (UTP type connector).

b

VIDEO OUT Video Signal Output Port (RCA jack).

c

AUDIO IN

Audio input signal port (

RCA jack, CH1).



For SEB-1006R (MIC integrated camera), it is also recommended not to connect other

input devices to the AUDIO IN port.



NETWORK NETWORK connector port.



DC 12V Camera and DVR power input port.



USB USB connector port.



ALARM IN 1~4, G : Alarm Input port.

ALARM OUT 1, COM : Alarm Output port.



VGA VGA Video Signal Output Port.



AUDIO OUT Audio Signal Output Port (RCA jack).

M



If using the VGA cable, the source from VGA will be displayed as main image on the screen along with the OSD

menus. Then, the BNC port will output the video signal alone.



If not using the VGA cable, the source from BNC will be displayed as main image on the screen along with the OSD

menus. If you connect the VGA cable after the system boot, only the video signal from VGA will be displayed.

1 2 3 4 G 1 COM G

ALARM IN

NETWORK

USB

CONSOLE

VGA

AUDIO IN

AUDIO OUT

VIDEO OUT

34

12

DC 12V

ALARM OUT

 b c  

 

12_ overview

overview

REMOTE CONTROL

Using the Numeric buttons

1. Press any button among 1 to 4.

2. Move to the selected channel number.

Changing the Remote Control ID

1. Press the ID button of the remote control and check the ID displayed on the DVR screen.

The factory default ID of the remote control is 00.

2. Enter 2 digits of your selection in order, while pressing the system [ID] button.

3. When ID input is done, press the system [ID] button again to check the setting.

M



If you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed.

Remote control's ID and DVR’s ID should be matched for proper operation. Refer to “Remote Devices”. (Page 45)

SEARCH

Displays the search menu.

POWER

Displays the Exit pop up screen.

EP10-000522

NUMBER [0~

+

10]

Used as the numeric input keys, or displays a single

channel.

T/W

Zooms in or out.

BACKUP

Displays the Backup Menu.

MODE

Changes the screen mode.

MENU

Goes to the system menu screen.

Up/Down/Left/Right(▲▼◄ ►)/ENTER

Moves the cursor up/down/left/right, and runs the

Select Menu.

FREEZE

Freezes the screen temporarily.

ZOOM

Runs the digital zoom (x2) function.

DVR

Activates the DVR function.

ID

Sets the ID of the system.

Select 2 digits from 0 ~ 9 while pressing the ID Key.

SCROLL ,.

Moves the menu scroll.

RETURN

Returns to the previous screen.

AUDIO

Turns Audio on/off.

ALARM

Cancels the Alarm.

REC LOCK

Selects the recording lock function.

PIP

Selects or deselects the PIP function.

REC

Starts or ends the live recording.

Skip Backward (by unit time),

Slow Rewind, Slow Forward,

Skip Forward (by unit time)

Move Frame

While paused, moves to the previous/next frame.

FR, STOP, PLAY/PAUSE, FF

English _13

 CONNECTING WITH OTHER DEVICE

INSTALLATION

Please take note of the followings before using this product.

• Do not use the product outdoor.

• Do not spill water or liquid in the connection part of the product.

• Do not impose the system to excessive shock or force.

• Do not pull out the power plug forcefully.

• Do not disassemble the product on your own.

• Do not exceed the rated input/output range.

• Use a certified power cord only.

• For the product with an input ground, use a grounded power plug.

CHECKING THE INSTALLATION ENVIRONMENT

Samsung Digital Video Recorder (“DVR” hereinafter) is a

state-of-art security device, and contains mass storage hard

disk(s) and critical circuits inside.

When the temperature rises inside the product, the product

may breakdown and the product life be shortened.

One Year: 24HR X 365 DAY =8,760 HR

Temperature

Unit: ºC

Life (Unit: HOURS)

connecting with other device

14_ connecting with other device

connecting with other device

CONNECTING THE VIDEO, AUDIO, AND MONITOR

M



Only one mouse port is available.

CONNECTING THE USB

1. By factory default, a USB port is provided for external connection.

2. You can connect a USB HDD, USB memory or mouse to the USB port.

3.

If a USB HDD is connected to the system, recognition and settings are available in “Menu > Setting the Device >

Storage Device”. (Page

43)

4. This product supports hot-plugging, which connects/removes the USB device during the system operation.

J



If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR.

1234G1COMG

ALARM IN

NETWORK

USB

CONSOLE

VGA

AUDIO IN

AUDIO OUT

VIDEO OUT

34

12

DC 12V

ALARM OUT

English _15

 CONNECTING WITH OTHER DEVICE

CONNECTING THE CAMERA

Equipped with the IR LED and the illumination sensor, enables you to monitor at night as well as in daytime.

The camera is suitable for both internal and external use.

Name Description



Camera Fitting

Groove

Groove that is used to fit the camera bracket.

There are two grooves; one on the top and one on the bottom.

b

IR LED These infrared LED's are controlled by the illumination sensor.

c

Lens Focal length of 3.6mm enables you to cover relatively longer range of monitoring.



Illumination Sensor Detects incoming light to control the IR LED.



DVR Connection

Cable

Connect the cable directly to the DVR without using a particular power cable.

You can use the RJ-45 cable to connect to a remote camera.

RJ-45 Cable (Length: 18.3m, 60ft)

This cable is specific to UTP connection, which is not compliant with the LAN cable. You can use the UTP

direct cable (all of 8 pins are used) to extend the length to a max of 200m. (based on UTP CAT 5e)

CVBS+

12V

CVBS-

N.C

GND 12V

GND(AUDIO)

GND

1. CVBS+

2. CVBS-

3. AUDIO

4. GND

5. 12V

6. N.C

7. N.C

8. N.C







SEB-1007RSEB-1005R

b

c



16_ connecting with other device

connecting with other device

Installing the camera

The camera can be installed on the wall, ceiling, shelf or a desired position using the provided bracket.

1. Select a position where you want to install the

camera.



Make sure the selected position can sustain the

weight of the camera.

2. Use the screw bolts (M4 X L15) to mount the

camera bracket onto the wall or ceiling.

3. Place the camera on the selected position and fit

the hole either on the top or the bottom of the

camera into the fixing bolt of the bracket, and

turn the camera clockwise.

J



You should be careful when installing the BOX

camera outdoors because the cable connectors

may be wet with moisture or pile up with impurities.

Camera Bracket

The camera bracket can be used to install the camera on the wall, ceiling or shelf.

Camera Bracket Specification

Name

Description

SEB-1005R SEB-1007R

Use

Indoor

Installation

Wall or Ceiling

Dimensions

57(W) X 47.2(H) X 100.5(L) mm/

2.25(W) X 1.86(H) X 3.95(L) inch

40(W) X 58(H) X 40(D) mm/

1.57(W) X 2.28(H) X 1.57(D) inch

Weight

130g(0.29 lbs) 55g (0.12 lbs)

Operating Temperature

-10˚C ~ 50˚C (14˚F ~ 122˚F)

Accessories

SCREW (M4 X L15) : 3 pcs

M4 X L15 sized

screws

wall or ceiling

M4 X L15

sized screws

wall or ceiling

SEB-1007RSEB-1005R

English _17

 CONNECTING WITH OTHER DEVICE

Adjusting the Camera Bracket

1. Choose an installation site that can sufficiently support the weight of

the equipments to be installed.

2. Attach the camera bracket to the wall using the supplied screws

(M4 X L15). 4x15 sized screws wall or ceiling.

3. Adjust the camera to target the video location and tighten the

camera bracket handle on the camera bracket. Install the camera

on to the male screw of the camera bracket by rotating the

camera clockwise.

4. Loosen the handle by turning it counter clockwise

and then adjust the camera position. Tighten the

handle, turning it clockwise to lock the camera in

position.

5. Connect the camera cable to the camera.

Handle

18_ connecting with other device

connecting with other device

CONNECTING THE ALARM INPUT/OUTPUT

Connecting the alarm input signal

Connection port for the alarm input signal.

Connect one strand of the sensor signal line (four strands) to

the alarm input port and connect the other to the [G] port.

Connecting the alarm output signal

Connection port for the alarm output signal.

Connect one strand of the sensor signal line to the alarm

output port and connect the other to the [COM] port.

• ALARM IN : 5mA sink

• ALARM OUT : 24V DC 1A, 125VAC/0.5A

1234G1COMG

ALARM IN

NETWORK

USB

CONSOLE

VGA

IN

UT

DC 12V

ALARM OUT

1234GG1COM

ALARM IN

ALARM OUT

U

SB

CO

N

SO

LE

VG

A

1

2

3

4

G

1

CO

M

A

LARM IN

ALARM

OUT

1234G1COMG

ALARM IN

ALARM OUT

English _19

 CONNECTING WITH OTHER DEVICE

CONNECTING THE NETWORK

Connecting to Network through Ethernet (10/100BaseT)

Connecting to the

Network using the router

1 2 3 4 G 1 COM G

ALARM IN

NETWORK

USB

CONSOLE

VGA

AUDIO IN

AUDIO OUT

VIDEO OUT

34

12

DC 12V

ALARM OUT

Windows

Network Viewer

Back Bone

Hub/Switcher

RJ-45 Ethernet Cable

(Direct Cable)

NETWORK

1 2 3 4 G 1 COM G

ALARM IN

NETWORK

USB

CONSOLE

VGA

AUDIO IN

AUDIO OUT

VIDEO OUT

34

12

DC 12V

ALARM OUT

External Remote PC

NETWORK

DDNS Server

(Data Center)

Broadband Router

xDSL or Cable

Modem

xDSL or Cable

Modem

20_ connecting with other device

connecting with other device

Connecting to Internet through ADSL

1 2 3 4 G 1 COM G

ALARM IN

NETWORK

USB

CONSOLE

VGA

AUDIO IN

AUDIO OUT

VIDEO OUT

34

12

DC 12V

ALARM OUT

Windows

Network Viewer

Phone(ADSL) Line

Hub/Switcher

ADSL MODEM

RJ-45 Ethernet Cable

(Direct Cable)

INTERNET

Page is loading ...

Samsung 4 channel DVR User manual

This manual is also suitable for

Samsung 4 channel DVR User manual

Related papers

Other documents