C1C28 INSTALL GUIDE
Model No. Gas Supply BTU's Regulator WC Pressure Max PSI Electrical Requirements
2 4
/2"
" 2
2 4
2
4" 2
2
2"
2
23"
2"
2
"
2 23"
C
utout Dimensions for Island
Overall Product Dimensions
When using a Coyote insulated jacket, you will want to build your island to the jackets Cutout and Overall Dimensions
listed above (detailed on 2nd page). Once the jacket is installed, the grill will rest on/inside the insulated jacket
2
/4"
2
/2"
2
/2"
/4"
"
3
/"
22
/"
Important Note to Installer: This file is not intended to replace your Owners' Manual which contains specific safety
requirements and consumer guidelines. Please refer to your Owners' Manual prior to installing or operating your built-in grill.
"
23"
2/4"
"
3/"
22/"
FRONT VIEW
TOP VIEW
REAR VIEW
SIDE VIEW
www.coyoteoutdoor.com
C1C28 INSTALL GUIDE
10
1
/4"
OPENING
HEIGHT
DOORS / DRAWERS
OPENING WIDTH
20
1
/2"
OPENING
DEPTH
OPENING
HEIGHT
GRILL
OPENING
GRILL
OVERHANG
TOP VIEW
25"
OPENING WIDTH
2
1
/2"
OPENING
HEIGHT
DOORS / DRAWERS
OPENING WIDTH
OPENING
DEPTH
OPENING
HEIGHT
24"
LINER
OPENING
7
/8"
JACKET
OVERHANG
TOP VIEW
OPENING WIDTH
24"
NON-COMBUSTIBLE CONSTRUCTION
Insulated Jacket NOT Required
FRONT VIEW
FRONT VIEW
1
1
/2" MIN
INCLUDING
COUNTERTOP
Combustible material can not be within 24" of the grills frame
This applies to all directions - horizontal & vertical
Shaded area above on "TOP VIEW" illustrates the 24" minimum
requirement (not to scale for rendering purposes)
The grill is designed to hang from the counter top with no support
underneath
Minimum rear clearance for the hood to open is 2"
If you have a wall/partition behind the grill, the minimum rear clearance
to that wall should be at least 7" to allow for ventilation of the exhaust
24"
If using combustible material within 24" of the grill frame, you MUST
use the corresponding Coyote Insulated Jacket
Using a insulated jacket, does not waive any other standard installation
procedure (ventilation, connections, etc)
The jacket is designed to hang from the counter top with no support
underneath
Minimum clearance for hood to open is 2"
If you have a wall/partition behind the grill, the minimum rear clearance
to that wall should be at least 7" to allow for ventilation of the exhaust
Ventilation Requirements:
Regardless if you are using a combustible or non-combustible building material, you must include at least two vents within
the island.
These vents must be at least 20 sq. in. each and allow fresh air to move from the grill cabinet to the exterior environment.
For a propane setup, the vents should be installed lower as propane is heavier than air.
For a natural gas setup, the vents should be located higher in the island, as natural gas is lighter than air.
Do not locate the two vents on the same wall of the island. Cross ventilation is key to allow any excess heat or trapped
gas to dissipate.
1
1
/2"
1
5
/8"
1
1
/2"
22
1
/8"
1
1
/2" MIN
COMBUSTIBLE CONSTRUCTION
Insulated Jacket Required - Model # CJAKTCC2
7
/8"
11"
INCLUDING
COUNTERTOP
28
1
/4"
1
3
/4"
2
1
/2"
2
1
/2"
2"
G
GAS
CONNECTION
G
4
1
/8"
4
1
/8"
G
GAS
CONNECTION
4
1
/8"
2
3
/4"
Important Note to Installer: This file is not intended to replace your Owners' Manual which contains specific safety
requirements and consumer guidelines. Please refer to your Owners' Manual prior to installing or operating your built-in grill.
-
1
-
2
Coyote CJAKTCC2 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Coyote C1P36-FS Installation guide
-
Coyote C1C28NG Owner's manual
-
-
Coyote C1P28 Installation guide
-
-
-
-
-
-
Coyote C1CH36 User guide
Other documents
-
Lynx L500PS-LP Owner's manual
-
Lynx Pro Models User guide
-
-
Dynamic Cooking Systems BH1-48RGI-N Installation guide
-
Lynx Grills L500RLP User manual
-
Lynx All Trident Models Owner's manual
-
Lynx Grills L36TRLP Owner's manual
-
Blaze BLZ5LTE2NG Owner's manual
-
Broilmaster BSG262N Owner's manual
-