Sharp ANWS350 Operating instructions

Brand: Sharp

Model: ANWS350

Type: Operating instructions

This manual is also suitable for

AN-WS350

Sharp ANWS350 is a TV stand with a metal base and a center bar, that can be assembled to different heights, from 1030 mm to 1250 mm. The stand is adjustable according to the size of the TV, it is suitable for 32" to 46" LCD TVs and has a maximum load of 10 kg. It can be secured to the wall with a safety wire or chain to prevent it from toppling over. The stand also has two glass shelves and a sound bar support, which can be used to enhance the sound of the TV. The stand is easy to assemble and comes with all the necessary parts.

RACK SOPORTE DE PIE

WALL ASIDE STAND

AN-WS350

AN-WS350R

MODELO

MODEL

Please refer to pages E-1 to E-14.

ENGLISH

Consulte las páginas S-1 a S-14

ESPAÑOL

MANUAL DE MANEJO

OPERATION MANUAL

...

AN-WS350_OM_FRONT.indd 1 2009-08-15 10:37:50

E-1

ENGLISH

Thank you for purchasing this SHARP product. Before using the product, please be sure to

read this operation manual carefully. In particular, be sure to read the section “To Ensure

Safe and Correct Use”. After reading the manual, keep it in a convenient location where it

can be accessed at any time.

Parts

Please conrm that the following parts are included.

WU V

METAL BASE x 1

LCD TV

SUPPORT (A) x 2

LCD TV

SUPPORT (B) x 2

LCD

U BRACKET x 1

CENTRE BAR x 1

LCD TV HOOK

x 2

SOUND BAR

SUPPORT x 1

SOUND BAR U

BRACKET x 1

SUPPORT

PLATE x 1

SCREWS

M8 [50mm] x 4

ALLEN KEY M6

x 1

ALLEN KEY M8

x 1

SOUND BAR

SPACER x 8

GLASS SHELF

SUPPORT

TV SPACER

x 4

SCREWS

M8 [16mm] x 4

SCREWS

M6 [35mm] x 6

SCREWS

M6 [16mm] x 53

SCREWS

M4 [12 mm] x 6

FLANGE

NUT x 20

SPRING

WASHER

Ø6 x 4

SPRING

WASHER

Ø8 x 8

GLASS x 2

CABLE COVER

x 1

BACK COVER

x 1

CABLE BAND x 2

LEFT x 2

RIGHT x 2

4 mm

5 mm

GLASS PROTECTOR x 4

SCREWS

M6 [45mm] x 4

SCREWS

M8 [45mm] x 4

AN-WS350_OM_EN.indd 1 2009-08-19 23:00:03

E-2

To Ensure Safe and Correct Use

This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays

and labels and incorrectly using the product could have results as classied below. Please read the following warning

symbol information before reading the rest of this section, and be sure to strictly observe all instructions.

Warning:

Not following these instructions could result in death or serious injury.

Caution:

Not following these instructions could result in injury or property damage.

Meaning of symbol

The symbol means something that should not be done.

Special Precautions for Safety

Warning:

z Follow the instructions in this manual regarding the installation method and installation orientation. Not following

these instructions could result in injury or damage from falling parts.

z Accurate work is required for the installation work, so please have it done by the dealer or qualied contractor.

z During installation, be careful not to pinch your ngers in the xture, etc.

z Do not apply any other loads to the installation xtures. Doing so could cause the TV to fall causing injury and

damage.

z Do not modify or change the installation parts. Doing so could cause the TV or sound bar system to fall causing

injury and damage.

z Be sure to install the stand on a solid and level oor. When assembling, lay the packing material on the oor to

avoid damage to the oor.

z Do not use a stand if it has sustained any cracks.

z Do not climb on the stand and do not use the stand as a footstool.

z Do not move the stand with the TV attached or with connected equipment inside.

z When using an electric screwdriver, set the torque setting to approximately 2.0 N-m (20 kgf-cm).

z This unit is suitable for SHARP LCD TV with sizes ranging from 32” to 46”.

z Do not use chemicals for cleaning (petrol, paint thinner, etc.). It may damage the cabinet nish. Periodically wipe

it with a soft cloth.

z Do not let children play around the TV stand as this might cause injury or the stand might fall on them.

z Do not step, stand or sit on the glass shelf.

z Maximum load on the glass shelf is 10 kg.

Caution:

Install in a location with low humidity and little dust. Install in a well-ventilated area.

z Do not install the LCD colour TV in a location

with high humidity and much dust. Doing so

could result in re or electric shock.

z Do not place the LCD colour TV where it will

come into contact with oily smoke or steam,

such as near a cooking range or humidi-

er. Doing so could result in re or electric

shock.

z Do not plug the air passage holes in the LCD

colour TV cabinet. Plugging the air passage

holes could trap heat inside the cabinet,

causing a re.

z Do not use the cabinet as follows. Do not

place the cabinet in a place with poor air cir-

culation, such as in a closet or bookcase. Do

not place a drop cloth, etc., on the installed

LCD colour TV.

Please strictly observe the following.

Special skill is required to install the LCD colour TV and Wall Aside Stand, so please have them installed by a

contractor specializing in such installation. The customer should not attempt to install the TV. Sharp shall not be

responsible for improper installation or any accidents, damage, or injury resulting from improper installation.

AN-WS350_OM_EN.indd 2 2009-08-19 23:00:05

E-3

Assembling the Centre Bar and Metal Base

Note:

Installation of this unit requires 2 or more

persons.

x 2

Step 1

Screw the Support Plate (G) to the Metal

Base with 2 pieces of M6 [16mm] screws

(K) rst, using the M6 Allen key (P).

Step 2

Flip the Metal Base upside down. You can

see the “SHARP” logo is facing upwards.

AN-WS350_OM_EN.indd 3 2009-08-19 23:00:05

E-4

Step 3

Place the Centre Bar next to the Metal Base, on top of the

Support Plate (G).

Step 4

From under the Metal Base, place 4 pieces of M8 [50mm]

screws (H) with Spring Washers Ø8 (O).

Step 5

Slowly lift the xture upwards and let it stand on the

oor.

Side view

Ensure that the specication label

is facing the oor when combining

the Centre Bar and Metal Base.

The screws should be tightened using Allen key M8 (Q)

according to the sequence A → B → C →D as shown

above.

AN-WS350_OM_EN.indd 4 2009-08-19 23:00:06

E-5

Assembling the Centre Bar and Metal Base (continued)

Step 6

Fasten another 4 pieces of M6 [16 mm]

screws (K) using M6 Allen key (P) to the

Support plate as shown.

Step 7

Before peeling off the masking tape securing the legs, hold the

legs rmly and be careful not to be hit by them. After peeling off

the tape, release the leg slowly until it fully opens out.

Be careful not to pinch your ngers

in the xtures.

Caution:

Note:

When pushing the stand against the

wall, the legs will bend inwards.

Note:

This product is designed to be located

against the wall. However, if the user

wishes to locate it further away from

the wall or at the centre of a room,

do ensure that the unit’s legs are fully

opened.

Specication label

Assembling the LCD Support Frame

Step 1

Fix the LCD Support Bar (A) with LCD U Bracket (C) using 4

pieces of M6 [16mm] screws (K) and 4 pieces of Flange Nuts

(M). Use M6 Allen key (P) to fasten the screws.

AN-WS350_OM_EN.indd 5 2009-08-19 23:00:12

E-6

Step 2

Slot in the LCD support frame to the Centre Bar as

shown.

Step 3

Fix the LCD Support Bar (A) with LCD U Bracket

pieces of Flange Nuts (M). Use M6 Allen key (P) to

fasten the screws.

Step 4

Fix the LCD Support Bar (B) using 8 pieces of M6

[16mm] screws (K) and 8 pieces of Flange Nuts

(M) as shown. Use M6 Allen key (P) to fasten the

screws.

Step 5

Screw the Support Frame to the Centre Bar using 6

pieces of M6 [16mm] screws (K). Fasten them with

M6 Allen key (P).

Do not hold the Support Frame at the

centre while inserting it to the Centre

Bar as this will cause injury.

Caution:

AN-WS350_OM_EN.indd 6 2009-08-19 23:01:04

E-7

Assembling the LCD Support Frame (continued)

Notes:

z The LCD Support Bar is adjustable to different heights.

Maximum height is 1250 mm. Minimum height is 1030 mm.

z When xing the frame, make sure that all the 6 pieces of M6

[16mm] screws are fastened to it.

z If adjusting to maximum height, make sure that you

do not exceed the stopper.

z When xing the frame to maximum height, make

sure that all the 6 pieces of M6 [16mm] screws are

fastened to it.

Stopper

Caution:

Minimum height = 1030 mm

Maximum height = 1250 mm

AN-WS350_OM_EN.indd 7 2009-08-19 23:01:26

E-8

Assembling the glass shelf

Falling prevention (optional)

Fix the safety wire or

chain to the wall using

a wall anchor bracket

which is commercially

available.

It is recommended to secure the xture to the

wall with a safety wire or chain before attach-

ing the TV to prevent it from toppling over in

case of earthquake occurrence.

Screw

Washer

Safety wire

(commercially

available)

surface

Step 1

Fix the left (S) and right (T) Glass Shelf Supports to the Centre

Bar using 4 pieces of M6 [16mm] screws (K) as shown. Fas-

ten them with Allen key M6 (P).

Step 2

Remove the transparent glass protective sheet at the bottom

surface of the glass. Top surface has a label afxed on it.

Peel off the separator of the double sided tape on the Glass

Protectors. Slot in 2 pieces of Glass Protector at the corners

of the glass as shown below.

Step 3

Peel off the separator of the double sided tape on the

left and right Glass Shelf Supports.

Double sided tape

Double

sided

tape

Label

Top surface

Glass protective

sheet

AN-WS350_OM_EN.indd 8 2009-08-19 23:01:34

E-9

Assembling the glass shelf (continued)

Step 4

Place the glass on the Glass Shelf Supports as shown.

Make sure all the Glass Protector guides are inserted

perfectly into the holes of the left and right Glass Shelf

Supports.

Notes:

z The glass is made of reinforced glass, but dropping

pointed objects on it or strongly hitting the surface may

cause it to break.

z The glass shelf is not fastened to the unit. Avoid han-

dling the glass when transporting the unit, otherwise it

may fall off and there is a risk of damage and injury.

Hole

Glass protector

guide

Assembling the Sound bar Support (optional)

Step 1

Fix the wall mount angle (comes with Sound bar

unit) to the Sound bar Support (E) using 4 pieces

of M4 [12mm] screws (L). Fasten them with a “+”

screw driver.

Step 2

Screw the Sound bar Support (E) to the Sound bar U Bracket

(F) using 4 pieces of M6 [35mm] screws (J) with 4 pieces of

Flange Nuts (M). Insert 8 pieces of Sound bar Spacers (R) as

shown below. Fasten them with M6 Allen key (P).

Notes:

You can omit the Sound bar Spacers (R) if you like but when

you do this, make sure that the screw type is changed from

M6 [35mm] (J) to M6 [16mm] (K)

You can include your Sound bar system to this unit to enhance the sound of your LCD TV.

WALL MOUNT ANGLE

(not supplied)

Label

AN-WS350_OM_EN.indd 9 2009-08-19 23:01:37

E-10

Assembling the Sound bar Support (optional) (continued)

Step 3

x 4

x 2

Step 3

Fasten the xture to the Centre Bar using 4 pieces

of M6 [16mm] screws (K) with M6 Allen key (P).

Step 4

Hook the sound bar to the Sound bar Support at

both sides.

Step 5

Fasten 2 pieces of M4 [12 mm] screws (L) to the

Sound bar Support as shown using a “+” screw

driver.

Step 6

Use the supplied Cable Band to tie the AC adaptor

of the Sound bar to the Sound bar Support.

AC adaptor

AN-WS350_OM_EN.indd 10 2009-08-19 23:01:51

E-11

Attaching the LCD TV Hook to the LCD TV

For lowerside TV Spacer xing:

turn the spacer guide upwards.

x 4

x 2

x 4

Step 1

Screw the LCD TV hooks to the

back of the LCD TV using 4 pieces

of M6 [16 mm] screws (K) with 4

pieces of Spring Washers Ø6 (N)

or 4 pieces of M8 [16 mm] screws

(I) with 4 pieces of Spring Washers

Ø8 (O), depending on the TV nut

size as shown. Fasten them using

M6 Allen key (P) or M8 Allen key

(Q).

Sharp shall not bear any responsibility

for damages, etc., caused by the LCD

colour TV falling due to insufcient in-

stallation strength or improper installa-

tion.

Caution:

LCD TV

Max. = 400 mm

Note:

The screw holes distance on the

TV for the LCD TV hook should

not exceed 400 mm by 400 mm.

Screw the LCD TV hooks to the

back of the LCD TV using 4 pieces

of M6 [45mm] screws (V) with 4

pieces of Spring Washers Ø6 (N) or

4 pieces of M8 [45mm] screws (W)

with 4 pieces of Spring Washers Ø8

(O), depending on the TV nut size

as shown. Fasten them using M6

Allen keys (P) or M8 Allen keys (Q).

Use below TV Spacer to x the LCD TV hooks.

For upperside TV Spacer xing:

turn the spacer guide downwards.

Spacer guide

Blu-Ray

Compartment

If using a Blu-Ray LCD TV (Optional)

AN-WS350_OM_EN.indd 11 2009-08-19 23:02:08

E-12

Wire arrangement

You can arrange and hide the cables at the back by using the sup-

plied Cable Cover.

Fix the Cable Cover to the Centre Bar using 3 pieces of M6 [16 mm]

screws (K) as shown. Fasten them using M6 Allen key (P).

Lift up the Cable Cover and insert all the cables neatly as shown.

Attaching the LCD TV Hook to the LCD TV (continued)

Step 2

Hook the TV to the LCD Support as shown.

Note:

LCD colour TVs have a viewing angle (range in which

the image can be viewed correctly). The best viewing

position is from directly in front of the screen. Deter-

mine the TV installation location after taking into con-

sideration the viewing posture, line of sight, and the

visual and aural ranges.

Step 3

Fasten 2 pieces of M6 [35 mm] screws (J) as

shown to x the TV position to prevent it from slid-

ing sideways. Use the M6 Allen key (P) to fasten

them.

AN-WS350_OM_EN.indd 12 2009-08-19 23:02:14

E-13

Specied products

The following products are subject to change without notice.

Certain models may not be available in certain regions.

There may be other models that can be used with this stand. For these models, refer to their operating instructions,

or the supplied leaet to verify that the stand can be used.

SHARP LCD colour TV SHARP Sound bar system

HT-SB200

HT-SB300

HT-SB400

HT-SB500

37XL8E

37D65E/DH65E

37X20E

37D44E

32LE700E

32LE600E

32DH77E

32SH7E/S7E

32XL8E

32D65E/DH65E

32X20E

32RD8E

32SB25E

32DH57D

32D44E

32A47E

46LE700E

46LE600E

46HD1E

46DH77E

46XL2E

46D65E/DH65E

46X20E

46X8E

42DH77E

42XL2E

42X20E

42SB55E

42SH7E

40LE700E

40LE600E

AN-WS350

AN-WS350R

Cleaning the stand

To remove any stain from the stand, wipe the surface with soft cloth. Do not use chemicals as it may damage the

surface nish.

Attaching the Back Cover

You can cover the wires at the back by attaching the Back Cover.

Slot in the Back Cover hooks (4 portions) into the LCD Support as

shown.

Peel off the protection sheet at both

sides of the Back Cover.

AN-WS350_OM_EN.indd 13 2009-08-19 23:02:16

E-14

Specication

(e)

100 mm

1021.7 mm (40 - 7/32”)

675 mm (26 - 9/16”)

470 mm (18 - 1/2”)

176 mm (6 - 15/16”)

100 mm (3 - 15/16”)

27 kg (59.52 lbs.)

60 kg (132.3 lbs.)

Dimensions

500 mm

380 mm

1021.7 mm

(a)

Weight

Stand maximum

load

10 kg (22.05 lbs.)

Glass shelf

maximum load

(b) (c) (d)

470 mm 176 mm 675 mm

Front view

Side view

AN-WS350_OM_EN.indd 14 2009-08-19 23:02:16

Sharp ANWS350 Operating instructions

Brand: Sharp

Model: ANWS350

Type: Operating instructions

This manual is also suitable for

AN-WS350

Download PDF

report

Sharp ANWS350 Operating instructions

This manual is also suitable for

Sharp ANWS350 Operating instructions

Related papers

Other documents