Marantz SR7500/A1B User manual

SR7500 / SR8500

PS7500 / PS8500

Please use this service manual with referring to the user guide ( D.F.U. ) without fail.

Service

Manual

SR7500 / SR8500

PS7500 / PS8500

AV Surround Receiver

SR7500 /A1B/A1S/K1G/L1G

/N1B/N1G/N1S/U1B

PS7500 /F1N

AV Surround Ampliﬁ er

Part no. 90M10BW855012

2nd Issue 2004.11

MJI

TABLE OF CONTENTS

SECTION PAGE

1. TECH NI CAL SPEC I FI CA TIONS ........................................................................................... 1

2. TECHNICAL DESCRIPTION ................................................................................................ 4

3. POWER AMPLIFIER AD JUST MENT ................................................................................... 8

4. SERVICE MODE................................................................................................................... 9

5. SYSTEM ERROR ...............................................................................................................11

6. UPDATE FIRMWARE.......................................................................................................... 12

7. WIRING DI A GRAM ............................................................................................................. 19

8. BLOCK DIAGRAM ..............................................................................................................21

9. SCHEMATIC DIAGRAM...................................................................................................... 23

10. PARTS LOCATION..............................................................................................................45

11. IC DATA............................................................................................................................... 61

12. EXPLODED VIEW AND PARTS LIST................................................................................. 85

13. ELECTRICAL PARTS LIST................................................................................................. 97

SR8500 /A1B/A1S/L1G/N1B

/N1G/N1S/U1B

PS8500 /F1N

AV SURROUND RECEIVER SR7500

POWER ON/OFF PHONES

STANDBY

L

C

R

SL S SR

LFE

DIGITAL

SURROUND

DISP MULTI AUTO TUNED ST SPKR A B V-O FF

NIGHT

PEAK ANALOG

DIGITAL

ATT

SLEEP SURR DIRECT

AUTO DISC 6.1 MTX 6.1

PCM

AAC

AUX 1 INPUT

AUDIOS-VIDEODIGITAL VIDEO L R

DOWN

UP

VOLUME

ENTER

INPUT SELECTOR

2nd EDITION

• 1, 25 and 27 pages were changed.

MARANTZ DESIGN AND SERVICE

Using superior design and selected high grade components, MARANTZ company has created the ultimate in stereo sound.

Only original MARANTZ parts can insure that your MARANTZ product will continue to perform to the speciﬁ cations for which

it is famous.

Parts for your MARANTZ equipment are generally available to our National Marantz Subsidiary or Agent.

ORDERING PARTS :

Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be speciﬁ ed.

The following information must be supplied to eliminate delays in processing your order :

1. Complete address

2. Complete part numbers and quantities required

3. Description of parts

4. Model number for which part is required

5. Way of shipment

6. Signature : any order form or Fax. must be signed, otherwise such part order will be considered as null and void.

SHOCK, FIRE HAZARD SERVICE TEST :

CAUTION : After servicing this appliance and prior to returning to customer, measure the resistance between either primary AC

cord connector pins ( with unit NOT connected to AC mains and its Power switch ON ), and the face or Front Panel of product and

controls and chassis bottom.

Any resistance measurement less than 1 Megohms should cause unit to be repaired or corrected before AC power is applied, and

veriﬁ ed before it is return to the user/customer.

Ref. UL Standard No. 1492.

In case of difﬁ culties, do not hesitate to contact the Technical

Department at above mentioned address.

041015MJI

USA

MARANTZ AMERICA, INC

1100 MAPLEWOOD DRIVE

ITASCA, IL. 60143

USA

PHONE : 630 - 741 - 0300

FAX : 630 - 741 - 0301

JAPAN

Technical

MARANTZ JAPAN, INC.

35- 1, 7- CHOME, SAGAMIONO

SAGAMIHARA - SHI, KANAGAWA

JAPAN 228-8505

PHONE : +81 42 748 1013

FAX : +81 42 741 9190

EUROPE / TRADING

MARANTZ EUROPE B.V.

P. O. BOX 8744, BUILDING SILVERPOINT

BEEMDSTRAAT 11, 5653 MA EINDHOVEN

THE NETHERLANDS

PHONE : +31 - 40 - 2507844

FAX : +31 - 40 - 2507860

AUSTRALIA

QualiFi Pty Ltd,

24 LIONEL ROAD,

MT. WAVERLEY VIC 3149

AUSTRALIA

PHONE : +61 - (0)3 - 9543 - 1522

FAX : +61 - (0)3 - 9543 - 3677

NEW ZEALAND

WILDASH AUDIO SYSTEMS NZ

14 MALVERN ROAD MT ALBERT

AUCKLAND NEW ZEALAND

PHONE : +64 - 9 - 8451958

FAX : +64 - 9 - 8463554

THAILAND

MRZ STANDARD CO., LTD

746 - 754 MAHACHAI ROAD.,

WANGBURAPAPIROM, PHRANAKORN,

BANGKOK, 10200 THAILAND

PHONE : +66 - 2 - 222 9181

FAX : +66 - 2 - 224 6795

TAIWAN

PAI- YUING CO., LTD.

6 TH FL NO, 148 SUNG KIANG ROAD,

TAIPEI, 10429, TAIWAN R.O.C.

PHONE : +886 - 2 - 25221304

FAX : +886 - 2 - 25630415

MALAYSIA

WO KEE HONG ELECTRONICS SDN. BHD.

2ND FLOOR BANGUNAN INFINITE CENTRE

LOT 1, JALAN 13/6, 46200 PETALING JAYA

SELANGOR DARUL EHSAN, MALAYSIA

PHONE : +60 - 3 - 7954 8088

FAX : +60 - 3 - 7954 7088

KOREA

MK ENTERPRISES LTD.

ROOM 604/605, ELECTRO-OFFICETEL, 16-58,

3GA, HANGANG-RO, YONGSAN-KU, SEOUL

KOREA

PHONE : +822 - 3232 - 155

FAX : +822 - 3232 - 154

SINGAPORE

WO KEE HONG DISTRIBUTION PTE LTD

No.1 JALAN KILANG TIMOR

#08-03 PACIFIC TECH CENTRE

SINGAPORE 159303

PHONE : +65 6376 0338

FAX : +65 6376 0166

CANADA

MARANTZ CANADA INC.

5-505 APPLE CREEK BLVD.

MARKHAM, ONTARIO L3R 5B1

CANADA

PHONE : 905 - 415 - 9292

FAX : 905 - 475 - 4159

1

1. TECHNICAL SPECIFICATIONS

FM TUNER SECTION [SR7500/SR8500]

Frequency Range.............................................87.5 - 108.0 MHz

Usable Sensitivity ........................................IHF 1.8 µV/16.4 dBf

Signal to Noise Ratio............................... Mono/Stereo 75/70 dB

Distortion.................................................Mono/Stereo 0.2/0.3 %

Stereo Separation ....................................................1 kHz 45 dB

Alternate Channel Selectivity ............................± 300 kHz 60 dB

Image Rejection ....................................................98 MHz 70 dB

Tuner Output Level ....................... 1 kHz, ± 75 kHz Dev 800 mV

AM TUNER SECTION [SR7500/SR8500]

Frequency Range...................................531 - 1602 kHz [/A/K/N]

...................................... 520 - 1710 kHz [/L/U]

Signal to Noise Ratio.......................................................... 50 dB

Usable Sensitivity.....................................................Loop 400µV

Distortion.............................................400 Hz, 30 % Mod. 0.5 %

Selectivity............................................................± 20 kHz 70 dB

AUDIO SECTION

[SR7500/PS7500]

Power Output (20 Hz - 20 kHz/THD=0.08%)

Front L&R................................................8 ohms 105 W / Ch

Center .....................................................8 ohms 105 W / Ch

Surround L&R .........................................8 ohms 105 W / Ch

Surround Back ........................................8 ohms 105 W / Ch

Front L&R................................................6 ohms 130 W / Ch

Center .....................................................6 ohms 130 W / Ch

Surround L&R .........................................6 ohms 130 W / Ch

Surround Back ........................................6 ohms 130 W / Ch

[SR8500/SR7500]

Power Output (20 Hz - 20 kHz/THD=0.08%)

Front L&R................................................8 ohms 110 W / Ch

Center .....................................................8 ohms 110 W / Ch

Surround L&R .........................................8 ohms 110 W / Ch

Surround Back ........................................8 ohms 110 W / Ch

Front L&R................................................6 ohms 145 W / Ch

Center .....................................................6 ohms 145 W / Ch

Surround L&R .........................................6 ohms 145 W / Ch

Surround Back ........................................6 ohms 145 W / Ch

Input Sensitivity/Impedance .......................... 168 mV/ 47 kohms

Signal to Noise Ratio

Analog Input / Source Direct.........................................105 dB

Frequency Response

Analog Input / Source Direct............8 Hz - 100 kHz (± 3 dB)

Digital Input / 96 kHz PCM................ 8 Hz - 45 kHz (± 3 dB)

VIDEO

Television Format ....................................................... NTSC/PAL

Input Level/Impedance....................................... 1 Vp-p/75 ohms

Output Level/Impedance .................................... 1 Vp-p/75 ohms

Video Frequency Response ....................5 Hz to 8 MHz (- 1 dB)

Video Frequency (Component) ..............5 Hz to 80 MHz (- 1 dB)

S/N .....................................................................................60 dB

GENERAL

Power Requirement.................................AC 240 V 50/60 Hz [/A]

.................................AC 100 V 50/60 Hz [/F]

......................................AC 220 V 50 Hz [/K]

......................................AC 110 V 60 Hz [/L]

..................................... AC 230 V 50 Hz [/N]

..................................... AC 120 V 60 Hz [/U]

Power Consumption............................ 600 W [SR7500/PS7500]

............................ 620 W [SR8500/PS8500]

Weight ...............................14.8 kg (32.6 Ibs) [SR7500/PS7500]

...............................15.0 kg (33.1 Ibs) [SR8500/PS8500]

ACCESSORIES

Remote Control Unit RC8500SR .............................................. 1

AAA-size batteries.................................................................... 3

Microphone MC-10................................................................... 1

Front AUX Jack Cover.............................................................. 1

AC cable................................................................................... 1

FM Antenna [SR7500/SR8500]................................................. 1

AM Loop Antenna [SR7500/SR8500] ....................................... 1

2

Output Channel Front information display

Surround Mode Input Signal Decoding L/R C SL SBL

SubW

Signal format indicators Channel status

SR SBR

AUTO Dolby Surr. EX Dolby Digital EX

OOOOO

2

DIGITAL EX L, C, R, SL, SR, S, LFE

Dolby D (5.1ch) Dolby Digital 5.1

OOO

-

O

2

DIGITAL L, C, R, SL, SR, LFE

Dolby D(2ch) Dolby Digital 2.0

O

-- - -

2

DIGITAL L, R

Dolby D (2ch Surr) Pro Logic

II

x movie

OOOO

-

2

DIGITAL ,

2

SURROUND L, R, S

DTS-ES DTS-ES

OOOOO

dts, ES L, C, R, SL, SR, S, LFE

DTS 96/24 DTS 96/24

OOO

-

O

dts 96/24 L, C, R, SL, SR, LFE

DTS (5.1ch) DTS 5.1

OOO

-

O

dts L, C, R, SL, SR, LFE

PCM(Audio) PCM (Stereo)

O

- - - - PCM L, R

PCM 96kHz PCM (96kHz Stereo)

O

- - - - PCM L, R

HDCD*Stereo

O

- - - - PCM, HDCD L, R

Analog Stereo

O

- - - - ANALOG -

PURE DIRECT Dolby D Surr. EX Dolby Digital EX

OOOOO

2

DIGITAL EX L, C, R, SL, SR, S, LFE

Dolby D (5.1ch) Dolby Digital 5.1

OOO

-

O

2

DIGITAL L, C, R, SL, SR, LFE

Dolby D (2ch) Dolby Digital 2.0

O

-- - -

2

DIGITAL L, R

Dolby D (2ch Surr) Pro Logic

II

x movie

OOOO

-

2

DIGITAL ,

2

SURROUND L, R, S

DTS-ES DTS-ES

OOOOO

dts, ES L, C, R, SL, SR, S, LFE

DTS 96/24 DTS 96/24

OOO

-

O

dts 96/24 L, C, R, SL, SR, LFE

DTS (5.1ch) DTS 5.1

OOO

-

O

dts L, C, R, SL, SR, LFE

PCM (Audio) PCM (Stereo)

O

- - - - PCM L, R

PCM 96kHz PCM (96kHz Stereo)

O

- - - - PCM L, R

HDCD*Stereo

O

- - - - PCM, HDCD L, R

Analog Stereo

O

- - - - ANALOG -

EX/ES Dolby D Surr. EX Dolby Digital EX

OOOOO

2

DIGITAL EX L, C, R, SL, SR, S, LFE

Dolby D (5.1ch) Dolby Digital EX

OOOOO

2

DIGITAL L, C, R, SL, SR, LFE

DTS-ES DTS-ES

OOOOO

dts , ES L, C, R, SL, SR, S, LFE

DTS 96/24 DTS-ES

OOOOO

dts 96/24 L, C, R, SL, SR, LFE

DTS(5.1ch) DTS-ES

OOOOO

dts L, C, R, SL, SR, LFE

DOLBY Dolby D Surr. EX Dolby Digital 5.1

OOOOO

2

DIGITAL EX L, C, R, SL, SR, S, LFE

(PL

II

x movie) Dolby D (5.1ch) Dolby Digital 5.1

OOOOO

2

DIGITAL L, C, R, SL, SR, LFE

(PL

II

x music) Dolby D (2ch) Pro Logic

II

x

OOOO

-

2

DIGITAL L, R

(PL

II

x game) Dolby D (2ch Surr) Pro Logic

II

x

OOOO

-

2

DIGITAL ,

2

SURROUND L, R, S

PCM (Audio) Pro Logic

II

x

OOOO

- PCM L, R

HDCD*Pro Logic

II

x

OOOO

- PCM, HDCD L, R

Analog Pro Logic

II

x

OOOO

- ANALOG -

DTS DTS-ES DTS 5.1

OOO

-

O

dts, ES L, C, R, SL, SR, S, LFE

(Neo:6 Cinema) DTS 96/24 DTS 96/24

OOO

-

O

dts 96/24 L, C, R, SL, SR, LFE

(Neo:6 Music) DTS (5.1ch) DTS 5.1

OOO

-

O

dts L, C, R, SL, SR, LFE

PCM (Audio) Neo:6

OOOO

- PCM L, R

Analog Neo:6

OOOO

- ANALOG -

Dolby D (2ch) Neo:6

OOOO

-

2

DIGITAL L, R

Dolby D (2ch Surr) Neo:6

OOOO

-

2

DIGITAL ,

2

SURROUND L, R, S

CS

II

Cinema PCM (Audio) CS

II

OOOOO

PCM L, R

CS

II

Music HDCD*CS

II

OOOOO

PCM, HDCD L, R

CS

II

Mono Analog CS

II

OOOOO

ANALOG -

Dolby D (2ch) CS

II

OOOOO

2

DIGITAL L, R

Dolby D (2ch Surr) CS

II

OOOOO

2

DIGITAL ,

2

SURROUND L, R, S

STEREO Dolby Surr. EX Stereo

O

-- -

O

2

DIGITAL EX L, C, R, SL, SR, S, LFE

Dolby D (5.1ch) Stereo

O

-- -

O

2

DIGITAL L, C, R, SL, SR, LFE

Dolby D (2ch) Stereo

O

-- - -

2

DIGITAL L, R

Dolby D (2ch Surr) Stereo

O

-- -

O

2

DIGITAL ,

2

SURROUND L, R, S

DTS-ES Stereo

O

-- -

O

dts, ES L, C, R, SL, SR, S, LFE

DTS 96/24 Stereo

O

-- -

O

dts 96/24 L, C, R, SL, SR, LFE

DTS (5.1ch) Stereo

O

-- -

O

dts L, C, R, SL, SR, LFE

PCM (Audio) Stereo

O

- - - - PCM L, R

PCM 96kHz Stereo

O

- - - - PCM L, R

HDCD*Stereo

O

- - - - PCM, HDCD L, R

Analog Stereo

O

- - - - ANALOG -

*: SR8500 only

*: PS8500 only

The relation between the selected surround mode and the input signal

The surround mode is selected with the surround mode buttons on SR7500/SR8500/PS7500/PS8500 or the remote control

unit. However, the sound you hear is subject to the relationship between the selected surround mode and input signal. That

relationship is as follows;

3

Note:

• Dolby Digital (2 ch: Lt/Rt): signal with Dolby

Surround flag Speakers are full set.

• No sound outputs from the surround speaker,

center speaker and subwoofer if the DVD disc has

no surround data.

Abbreviations

L/R : Front speakers

C : Center speaker

SL/SR : Surround speakers

SBL/SBR : Surround Back speakers

SubW : Sub woofer speaker

*

*: SR8500 only

Output Channel Front information display

Surround Mode Input Signal Decoding L/R C SL SBL

SubW

Signal format indicators Channel status

SR SBR

Virtual Dolby Surr. EX Virtual

O

-- - -

2

DIGITAL EX L, C, R, SL, SR, S, LFE

Dolby D (5.1ch) Virtual

O

-- - -

2

DIGITAL L, C, R, SL, SR, LFE

Dolby D (2ch) Virtual

O

-- - -

2

DIGITAL L, R

Dolby D (2ch Surr) Virtual

O

-- - -

2

DIGITAL ,

2

SURROUND L, R, S

DTS-ES Virtual

O

- - - - dts, ES L, C, R, SL, SR, LFE

DTS (5.1ch) Virtual

O

- - - - dts L, C, R, SL, SR, LFE

PCM (Audio) Virtual

O

- - - - PCM L, R

HDCD*Virtual

O

- - - - PCM, HDCD L, R

Analog Virtual

O

- - - - ANALOG -

Multi Ch. Dolby Surr. EX Multi Channel Stereo

OOOOO

2

DIGITAL EX L, C, R, SL, SR, S, LFE

Stereo Dolby D (5.1ch) Multi Channel Stereo

OOO

-

O

2

DIGITAL L, C, R, SL, SR, LFE

Dolby D (2ch) Multi Channel Stereo

OOOO

-

2

DIGITAL L, R

Dolby D (2ch Surr) Multi Channel Stereo

OOOO

-

2

DIGITAL ,

2

SURROUND L, R, S

DTS-ES DTS-ES

OOOOO

dts, ES L, C, R, SL, SR, S, LFE

DTS (5.1ch) DTS 5.1

OOO

-

O

dts L, C, R, SL, SR, LFE

PCM (Audio) Multi Channel Stereo

OOOO

- PCM L, R

HDCD*Multi Channel Stereo

OOOO

- PCM, HDCD L, R

Analog Multi Channel Stereo

OOOO

- ANALOG -

THX Dolby Surr. EX THX Surround EX + Dolby Digital

OOOOO

2

DIGITAL EX L, C, R, SL, SR, S, LFE

Dolby D (5.1ch) THX + Dolby Digital

OOO

-

O

2

DIGITAL L, C, R, SL, SR, LFE

Dolby D (2ch) THX + Pro Logic

II

x

OOOO

-

2

DIGITAL L, R

Dolby D (2ch Surr) THX + Pro Logic

II

x

OOOO

-

2

DIGITAL ,

2

SURROUND L, R, S

DTS-ES THX + DTS-ES

OOOOO

dts, ES L, C, R, SL, SR, S, LFE

DTS 96/24 THX + DTS

OOO

-

O

dts 96/24 L, C, R, SL, SR, LFE

DTS (5.1ch) THX + DTS

OOO

-

O

dts L, C, R, SL, SR, LFE

PCM (Audio) THX + Pro Logic

II

x

OOOO

- PCM L, R

HDCD*THX + Pro Logic

II

x

OOOO

- PCM, HDCD L, R

Analog THX + Pro Logic

II

x

OOOO

- ANALOG -

*: PS8500 only

4

2. TECHNICAL DESCRIPTION

THX® is an exclusive set of standards and

technologies established by the world-renowned

film production company, Lucasfilm Ltd. THX

resulted from George Lucas’ desire to reproduce

the movie soundtrack as faithfully as possible both

in the movie theater and in the home theater.

THX engineers developed patented technologies

to accurately translate the sound from a movie

theater environment into the home, correcting the

tonal and spatial errors that occur.

When the THX mode of the SR7500 is on, three

distinct THX technologies are automatically

added:

Re-Equalization-restores the correct tonal balance

for watching a movie in a home environment.

These sounds are otherwise mixed to be brighter

for a large movie theater. Re-EQ compensates for

this and prevents the soundtracks from being

overly bright and harsh when played in a home

theater.

Timbre Matching-filters the information going to

the surround speakers so they more closely match

the tonal characteristics of the sound coming from

the front speakers.

This ensures seamless panning between the front

and surround speakers.

Adaptive Decorrelation-slightly changes one

surround channel’s time and phase relationship

with respect to the other surround channel.

This expands the listening position and creates

with only two surround speakers the same

spacious surround experience as in a movie

theater with multiple surround speakers.

The Marantz SR7500 was required to pass a

rigorous series of quality and performance tests, in

addition to incorporating the technologies

explained above, in order to be THX certified by

Lucasfilm Ltd.

THX requirements cover every aspect of

performance including pre-amplifier and power

amplifier performance and operation, and

hundreds of other parameters in both the digital

and analog domain.

Movies which have been encoded in Dolby Digital,

DTS, Dolby Pro Logic, stereo and Mono will all

benefit from the THX mode when being viewed.

The THX mode should only be activated when

watching movies which were originally produced

for a movie theater environment.

This is because they were originally mixed for a

small room environment.

THX is a trademark or registered trademark of THX

Ltd. Surround EX is a jointly developed technology

of THX and Dolby Laboratories, Inc. and is a

trademark of Dolby Laboratories, Inc. Used under

THX Surround EX—Dolby DIgital Surround EX is a

joint development of Dolby Laboratories and THX

Ltd.

In a movie theater, film soundtracks that have been

encoded with Dolby Digital Surround EX

technology are able to reproduce an extra channel

which has been added during the mixing of the

program. This channel, called Surround Back,

places sounds behind the listener in addition to the

currently available front left, front center, front

right, surround right, surround left and subwoofer

channels. This additional channel provides the

opportunity for more detailed imaging behind the

listener and brings more depth, spacious

ambience and sound localization than ever before.

Movies that were created using the Dolby Digital

Surround EX technology, when released into the

home consumer market may exhibit wording to that

effect on the packaging. A list of movies created

using this technology can be found on the Dolby

web site at www.dolby.com. A list of available

DVD software titles encoded with this technology

an be found at www.thx.com.

Only receiver and controller products bearing the

THX Surround EX logo, when in the THX Surround

EX mode, faithfully reproduce this new technology

in the home. This product may also engage the

THX Surround EX mode during the playback of 5.1

channel material that is not Dolby Digital Surround

EX eocnded. In such case, the information

delivered to the Surround Back channel will be

program dependent and may or may not be very

pleasing depending on the particular soundtrack

and the tastes of the individual listener.

“SURROUND EX™” is a trademark of Dolby

Laboratories. Used under authorization.

5

DTS was introduced in 1994 to provide 5.1

channels of discrete digital audio into home theater

systems.

DTS brings you premium quality discrete

multichannel digital sound to both movies and

music.

DTS is a multichannel sound system designed to

create full range digital sound reproduction.

The no compromise DTS digital process sets the

standard of quality for cinema sound by delivering

an exact copy of the studio master recordings to

neighborhood and home theaters.

Now, every moviegoer can hear the sound exactly

as the moviemaker intended.

DTS can be enjoyed in the home for either movies

or music on of DVD’s, LD’s, and CD’s.

“DTS” and “DTS Digital Surround” are registered

trademarks of Digital Theater Systems, Inc.

The advantages of discrete multichannel systems

over matrix are well known.

But even in homes equipped for discrete

multichannel, there remains a need for high-quality

matrix decoding. This is because of the large

library of matrix surround motion pictures available

on disc and on VHS tape; and analog television

broadcasts.

The typical matrix decoder of today derives a

center channel and a mono surround channel from

two-channel matrix stereo material. It is better than

a simple matrix in that it includes steering logic to

improve separation, but because of its mono,

band-limited surround it can be disappointing to

users accustomed to discrete multichannel.

Neo:6 offers several important improvements as

follow,

• Neo:6 provides up to six full-band channels of

matrix decoding from stereo matrix material.

Users with 6.1 and 5.1 systems will derive six

and five separate channels, respectively,

corresponding to the standard home-theater

speaker layouts.

• Neo:6 technology allows various sound

elements within a channel or channels to be

steered separately, and in a way which follows

naturally from the original presentation.

the subtlety and integrity of the original stereo

recording.

DTS-ES Extended Surround is a new multichannel

digital signal format developed by Digital Theater

Systems Inc. While offering high compatibility with

the conventional DTS Digital Surround format,

DTS-ES Extended Surround greatly improves the

360-degree surround impression and space

expression thanks to further expanded surround

signals. This format has been used professionally

in movie theaters since 1999.

In addition to the 5.1 surround channels (FL, FR,

C, SL, SR and LFE), DTS-ES Extended Surround

also offers the SB (Surround Back) channel for

surround playback with a total of 6.1 channels.

DTS-ES Extended Surround includes two signal

formats with different surround signal recording

methods, as DTS-ES Discrete 6.1 and DTS-ES

Matrix 6.1.

“DTS”, “DTS-ES and “Neo:6” are trademarks of

Digital Theater Systems, Inc.

The stereo CD is a 16-bit medium with sampling at

44.1 kHz. Professional audio has been 20- or 24-

bit for some time, and there is increasing interest in

higher sampling rates both for recording and for

delivery into the home. Greater bit depths provide

extended dynamic range. Higher sampling rates

allow wider frequency response and the use of

anti-alias and reconstruction filters with more

favorable aural characteristics.

DTS 96/24 allows for 5.1channel sound tracks to

be encoded at a rate of 96kHz/24bits on DVD-

Video titles.

When DVD-video appeared, it became possible to

deliver 24-bit, 96 kHz audio into the home, but only

in two channels, and with serious limitations on

picture. This capability has had little use.

DVD-audio allows 96/24 in six channels, but a new

player is needed, and only analog outputs are

provided, necessitating the use of the D/A

converters and analog electronics provided in the

player.

6

DTS 96/24 offers the following:

1. Sound quality transparent to the original 96/24

master.

2. Full backward compatibility with all existing

decoders. (Existing decoders will output a 48

kHz signal)

3. No new player required: DTS 96/24 can be

carried on DVD-video, or in the video zone of

DVD-audio, accessible to all DVD players.

4. 96/24 5.1-channel sound with full-quality full-

motion video, for music programs and motion

picture soundtracks on DVD-video.

“DTS” and “DTS 96/24” are trademarks of Digital

Theater Systems, Inc.

Dolby Digital identifies the use of Dolby Digital

audio coding for such consumer formats as DVD

and DTV. As with film sound, Dolby Digital can

provide up to five full-range channels for left,

center, and right screen channels, independent left

and right surround channels, and a sixth (“.1”)

channel for low-frequency effects.

Dolby Surround Pro Logic

II

is an improved matrix

decoding technology that provides better spatiality

and directionality on Dolby Surround program

material; provides a convincing three-dimensional

soundfield on conventional stereo music

recordings; and is ideally suited to bring the

surround experience to automotive sound. While

conventional surround programming is fully

compatible with Dolby Surround Pro Logic

II

decoders, soundtracks will be able to be encoded

specifically to take full advantage of Pro Logic

II

playback, including separate left and right

surround channels. (Such material is also

compatible with conventional Pro Logic decoders.)

Dolby Digital EX creates six full-bandwidth output

channels from 5.1-channel sources. This is done

using a matrix decoder that derives three surround

channels from the two in the original recording.

For best results, Dolby Digital EX should be used

with movies soundtracks recorded with Dolby

Digital Surround EX.

About Dolby Pro Logic

II

x

Dolby Pro Logic IIx technology delivers a natural

and immersing 7.1-channel listening experience to

the home theater environment. A product of

Dolby's expertise in surround sound and matrix

decoding technologies, Dolby Pro Logic II x is a

complete surround sound solution that maximizes

the entertainment experience from stereo as well

as 5.1-channel encoded sources.

Dolby Pro Logic IIx is fully compatible with Dolby

Surround Pro Logic technology and can optimally

decode the thousands of commercially available

Dolby Surround encoded video cassettes and

television programs with enhanced depth and

spatiality. It can also process any high-quality

stereo or Advanced Resolution 5.1-channel music

content into a seamless 6.1- or 7.1-channel

listening experience.

The Dolby Headphone technology provides a

surround sound listening experience over headphones.

When listening to multichannel content such as

DVD movies over headphones, the listening

experience is fundamentally different than

listening to speakers. Since the headphone

speaker drivers are covering the pinna of the ear,

the listening experience differs greatly from

traditional speaker playback. Dolby utilizes

patented headphone perspective curves to solve

this problem and provides a non-fatiguing,

immersive, home theater listening experience.

Dolby Headphone also delivers exceptional 3D

audio from stereo material.

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic”, and the double-

D symbol are trademarks of Dolby Laboratories.

7

Circle Surround II (CS-II) is a powerful and

versatile multichannel technology. CS-II is

designed to enable up to 6.1 multichannel surround

sound playback from mono, stereo, CS encoded

sources and other matrix encoded sources. In all

cases the decoder extends it into 6 channels of

surround audio and a LFE/subwoofer signal. The

CS-II decoder creates a listening environment that

places the listener “inside” music performances

and dramatically improves both hi-fi audio

conventional surround-encoded video material.

CS-II provides composite stereo rear channels to

greatly improve separation and image positioning–

adding a heightened sense of realism to both audio

and A/V productions.

CS-II is packed with other useful feature like dialog

clarity (SRS Dialog) for movies and cinema-like

bass enrichment (TruBass). CS-II can enable the

dialog to become clearer and more discernable in

movies and it enables the bass frequencies

contained in the original programming to more

closely achieve low frequencies–overcoming the

low frequency limitations of the speakers by full

octave.

Circle Surround II , Dialog Clarity, TruBass, SRS

and symbol are trademarks of SRS Labs, Inc.

Circle Surround II, Dialog Clarity and TruBass

technology are incorporated under license from

SRS Labs, Inc.

(SR8500 only)

HDCD® (High Definition Compatible Digital ®) is a

patented process for delivering on Compact Disc

the full richness and details of the original

microphone feed.

HDCD encoded CDs sound better because they

are encoded with 20-bits of real musical

information as compared to 16-bits for all other

CDs.

HDCD overcomes the limitation of the 16-bit CD

format by using a sophisticated system to encode

the additional four bits onto the CD while remaining

completely compatible with the CD format.

When listening to HDCD recordings, you hear

more dynamic range, a focused 3-D sound stage,

and extremely natural vocal and musical timbre.

With HDCD, you get the body, depth and emotion

of the original performance not a flat, digital

imitation.

HDCD system manufactured under license from

Microsoft. This product is covered by one or more

of the following: In the United States 5,479,168

5,638,074 5,640,161 5,808,574 5,838,274

5,854,600 5,864,311 5,872,531 and in Australia

669,114 with other patents pending.

8

3. POWER AMPLIFIER ADJUSTMENT

Idling Current Alignment

1. Each of the measurement points are provided with the

two test points. Set a digital Voltage meter to DC voltage

input, connect the meter to the test points at both con-

tact points.

2. After the setup above, turn on the main switch.

3. Adjust variable resistors (VR41, VR42…VR71) accord-

ing to the digital voltmeter readings. The target setting

value is the following table for each channel.

Settings: Master Volume — Minimum

Speaker out — No Load

Top lid — OPEN

Channel Alignment Point Measurement Point

Front L VR41 CN41

Center VR61 CN61

Front R VR51 CN51

Surround L VR42 CN42

Surround R VR52 CN52

Surround Back L VR62 CN62

Surround Back R VR71 CN71

Time Table of Idling Current Rise

After Turning ON

Ambient temperature

20 to 30 degrees centigrade

Measurement Voltage

10 min. 2.4 mV ± 0.3 mV

20 min. 2.4 mV ± 0.3 mV

30 min. 2.4 mV ± 0.3 mV

9

SERV I CE MODE

SR8500

V040805 1U

Month Date Dest.

(Dest. : Destination)

Year

CODE TYPEXXXX

(XXXX is displayed in Hex)

CD01 01020101

SIGDev. TYP Ver.No.

No. : DISP CODE ID Dev. : Device ID SIG. : CODE SIG ID

TYP. : CODE TYPE ID Ver. : Version

SOFT TYPE XX

(XX is displayed in Hex)

4. SERVICE MODE

Microprocessor (IC36), DSP(IC20 )Version and FLD Seg-

ment Check Mode.

1. While the power is on, PURE DIRECT, MRAC and 7.1CH

INPUT buttons simultaneously more than 3 seconds.

The FL display shows “SERVICE MODE” for 2 seconds

then shows the model name.

2. Press ENTER button, The software version of the micro-

processor (IC36) is displayed in the format below.

3. Press ENTER button again, The software Serial Number

that is wirtten in the factory is displayed.

4. Press ENTER button again, The software Type Number

is displayed.

5. Press ENTER button again, The Code Group Type

Number is displayed.

6. Press ENTER button again, The left half, right half and

center of the label area in the FLD light on and off each

other.

7. Press ENTER button again, The segments of the char-

acter area in the FLD ﬂ ick in checker pattern.

8. Press ENTER button again, All the FL segments turns

off.

9. Press ENTER button again. Every time ENTER button

is pressed, DSP code is indicated in turn from NO.1 to

NO.28.

MZXXXXXXXXXXX

10. Press ENTER button again to quit this mode. 10 ENTER ȜǿȳǛ਀ƠǇƢŵǵȸȓǹȢȸȉƸᚐᨊƞǕ

ǇƢŵ

MZXXXXXXXXXXX

6. ENTER ȜǿȳǛ਀ƠǇƢŵFL ᘙᅆƷӫŴ߼Ŵɶځᢿ

Ўƕʩʝƴໜ༔ǛጮǓᡉƠǇƢŵ

7. ENTER ȜǿȳǛ਀ƠǇƢŵFL ƷCharacter ᢿЎƕໜ

๒ƠǇƢŵ

8. ENTER ȜǿȳǛ਀ƠǇƢŵFL ƕμෞ໊ƠǇƢŵ

9. ENTER ȜǿȳǛ਀ƠǇƢŵENTER ȜǿȳǛ਀Ƣࡇƴ

DSP Code ID ƕNO.1 Ɣǒ NO.28 Ǉư᪯ƴᘙᅆƞǕǇ

Ƣŵ

5. ENTER ȜǿȳǛ਀ƠǇƢŵCode Group Type ƕᘙᅆƞ

ǕǇƢŵ

4. ENTER ȜǿȳǛ਀ƠǇƢŵȞǤǳȳᲢ

IC36ᲣƷ

Soft ware Type ƕᘙᅆƞǕǇƢŵ

3. ENTER ȜǿȳǛ਀ƠǇƢŵ߻ئư୿ƖᡂǈฎǈƷ

Software Serial No. ƕᘙᅆƞǕǇƢ

2. ENTER ȜǿȳǛ਀ƠǇƢŵȞǤǳȳᲢIC36ᲣƷȐȸǸȧ

ȳƕഏƷǑƏƴᘙᅆƞǕǇƢŵ

4. SERVICE MODE

Microprocessor (IC36), DSP(IC20 ) ƷVersion ᘙᅆӏƼ FL

ໜ༔ǛᄩᛐƢǔȢȸȉưƢŵ

1. ǻȃȈƷᩓเǛλǕǇƢŵPURE DIRECT Ŵ

MRAC Ŵ

7.1CH IN PUT ƷȜǿȳǛӷ଺ƴኖ 3ᅺˌɥ਀ƠǇƢŵ

“SERVICE MODE” ƱᘙᅆƕЈǇƢŵ୼ƴኖ 2ᅺࢸƴೞ

ᆔӸƕᘙᅆƞǕǇƢŵ

SERV I CE MODE

SR8500

CD01 01020101

SIGDev. TYP Ver.No.

No. : DISP CODE ID Dev. : Device ID SIG. : CODE SIG ID

TYP. : CODE TYPE ID Ver. : Version

CODE TYPEXXXX

(XXXX: Hex )

SOFT TYPE XX

(XX: Hex )

V040805 1U

Month Date Dest.

Year

10

Note: Step4, 5 is to check if CPU software is capable of

DSP code. “Software Type No” is to show what “DSP

Code Group” CPU is capable of. And vice versa.

Step 9 is to manage the 40 codes for DSP.

• When the unit is once turned into Service Mode, the

unit keeps this mode until the main power is turned

off. (Turning into stand-by mode does not make it

quit from Service Mode.) When the unit quits from

Service Mode, Information in the memory is also

cleared and the unit returns to the status when it is

out from the factory.

Product Reset

To reset the back up memory of the unit into the default sta-

tus, follow the procedure below.

1. Turn of the unit and press SPEAKERS A/B and MULTI

button simultaneously more than 1.5 seconds.

2. After “DEFAULT” is displayed on FLD, power is turned

off once and turned of again, EEPROM is cleared to

the default status, µ-com is reset and the unit returns to

the normal status. (Software Serial Number will not be

cleared.)

Note: When the unit is shipped from the factory, the proce-

dure above must be done to set the unit to initial sta-

Personal notes:

11

5. SYSTEM ERROR

When the microcomputer detects a trouble, the following in-

formation is displayed on the FLD.

• After the error contents indication, Surround Mode is

initialized and returned Factory mode.

• The contents of the ERROR indication are the followings.

1. Trouble in DSP

If communication with DSP is troubled more than 2

seconds.

2. Trouble in DSP Code

The trouble of DSP Code was found.

3. Trouble in EEP-ROM

If data from EEPROM does not match.

4. Trouble in EEP-ROM IF

If communication with EEPROM is troubled more than 2

seconds.

5. Trouble in RS-232C

If communication of Panja with RS232C is troubled more

than 2 seconds.

6. Trouble in 5V Supply

If 5V supply to DATA DIR is troubled.

7. Trouble in Protection

CPU turns off the speaker output.

Indication is keep and sound is mute.

CHECK DSP ROM

CHECK E2P I F

CHECK E2P

CHECK 2 32C

CHECK POW5

PROTECT

CHECK DSP ROM

 ᘙᅆཞ७ƸƦƷǇǇư᪦٣Ƹ /WVG ཞ७

5. SYSTEM ERROR

ᙌԼϋᢿưƷီࠝႆဃ଺ƴϼྸŴᘙᅆǛᘍƍǇƢŵɼƴӲ

Device ƱƷᡫ̮ီࠝǛ౨ЈƠǇƢŵ

᳽ ERROR ᘙᅆࢸŴSurroundMode ƸИ஖҄ƞǕ߻ئЈᒵ

Ʒཞ७ƴ৏ǓǇƢŵ

᳽ ERROR ᘙᅆƷϋܾƸɦᚡưƢŵ

1. DSP

ီࠝ౨Јᘙᅆŵ

 DSP ƱƷᡫ̮ɥƷɧφӳǛኖ  ᅺ౨ЈƠƨ଺ŵ

2. DSP Code

ီࠝ౨Јᘙᅆŵ

 DSPCode ƷီࠝǛ౨ЈƠƨ଺ŵ

3. EEP-ROM

ီࠝ౨Јᘙᅆŵ

 EEPROMData ƷɧૢӳǛ౨ЈƠƨ଺ŵ

4. EEP-ROM IF

ီࠝ౨Јᘙᅆŵ

 EEPROM ƱƷᡫ̮ɧφӳƕኖ  ᅺˌɥဃơƨ଺ŵ



5. RS-232C

ီࠝ౨Јᘙᅆŵ

 Panja ᡫ̮଺ƴ RSCƱƷᡫ̮ɧφӳǛኖ  ᅺˌ

ɥ౨ЈƠƨ଺ŵ

6. 5V

ီࠝ౨Јᘙᅆŵ

 DATADIR ƷီࠝǛ౨ЈƠƨ଺ŵ

7. Protection

̮ӭီࠝ౨Јᘙᅆŵ

 Speaker ƔǒǛЈщǛഥǊǇƢŵ

CHECK DSP ROM

CHECK E2P I F

CHECK E2P

CHECK 2 32C

CHECK POW5

PROTECT

CHECK DSP ROM

12

6. UPDATE FIRMWARE

Software for CPU and DSP can be updated.

Have update application software. (“UpgradeDSP.exe” and

“H8Download.exe”)

There are two mode of download, regarding to the target of

software as bellow.

Mode 1: Update DSP’s software to Flash-ROM.

This mode is to update the software for DSP.

The target devise is Flash-ROM (IC20) on CUP11762Z

(DSP PCB).

The Unit needs to be set update condition, by three front

keys.

Mode 2: Update CPU’s software to internal Flash-ROM.

This mode is to update the software for DSP.

The target devise is internal ﬂ ash ROM of CPU (IC36) on

CUP11762Z (DSP PCB).

The Unit needs to be set to writing condition, by pushing

internal switch from back-panel.

The following items are required for updating.

RS232C Dsub-9 pin cable (female to female/Straight type)

Windows PC (98, NT, ME, 2000) with RS-232C port.

Update software to CPU.

Update software to DSP.

Use RS232C Dsub-9 pin cable (female to female/Straight

type) to connect PC and the unit.

COM port on PC needs to be set by dialog box for each pro-

gram. COM port can be set from COM1 to COM5.

Download Firmware for DSP (Mode 1)

1. Put the “DSP upgrade” folder into anywhere on your PC’

s hard disc.

2. Connect PC and the unit with the RS-232C cable.

3. Turn on the unit.

6. UPDATE FIRMWARE

CPU ƓǑƼ DSP ǽȕȈǦǧǢƷǢȃȗȇȸȈǛᘍƍǇƢ 

ǽȕȈǦǧǢƷǢȃȗȇȸȈƴƸUpgradeDSP.exe Ʊ

H8Download.exe ƕ࣏ᙲưƢŵ

ǢȃȗȇȸȈƴƸഏƷʚƭƷȢȸȉƕƋǓǇƢŵ

Mode 1:DSP ဇFlash-ROM ƷǢȃȗȇȸȈ

ƜƷȢȸȉƸ DSP ƷǽȕȈǦǧǢǛǢȃȗȇȸȈƢǔȢȸ

ȉưƢŵ

CUP11762(DSP PCB) ƷؕெɥƴƋǔ Flash-ROM (IC20)

ƷǽȕȈǦǧǢǛǢȃȗȇȸȈƠǇƢŵ

ஜೞ [PS7500 / PS8500] ƷȕȭȳȈȑȍȫƴƋǔ 3ƭƷȜ

ǿȳǛ਀ƠƯǢȃȗȇȸȈȢȸȉƴƠǇƢŵ

Mode 2:CPU Ʒϋᢿ Flash-ROM ƷǢȃȗȇȸȈ

ƜƷȢȸȉƸ CPU ƷǽȕȈǦǧǢǛǢȃȗȇȸȈƢǔȢȸ

ȉưƢŵ

CUP11762(DSP PCB) ƷؕெɥƴƋǔ CPU(IC36) Ʒϋᢿ

Flash-ROM ƷǽȕȈǦǧǢǛǢȃȗȇȸȈƠǇƢŵ

ஜೞ [PS7500 / PS8500] ƷȪǢȑȍȫƔǒϋᢿǹǤȃȁǛ

਀ƠƯǢȃȗȇȸȈȢȸȉƴƠǇƢŵ

ǢȃȗȇȸȈƴƸɦᚡƷೞ֥ƕ࣏ᙲưƢŵ(࣏ᙲೞ֥ )

RS-232C ǹȈȬȸȈǱȸȖȫ (9Pin ȡǹ -9Pin ȡǹ )

Windows PC Serial Port ˄Ɩ (OS: 98,NT,ME,2000)

CPU ဇǢȃȗȇȸȈǽȕȈǦǧǢ

DSP ဇǢȃȗȇȸȈǽȕȈǦǧǢ

RS-232C ǱȸȖȫưஜೞƱ੗ዓƢǔ PC ƷCOM ȝȸȈဪӭ

ǛᚨܭƠƯƘƩƞƍŵ

COM ȝȸȈဪӭƸ COM1 Ɣǒ COM5 ǇưᚨܭưƖǇƢŵ

DSP

ƷǢȃȗȇȸȈ૾ඥ

ƷǢȃȗȇȸȈ૾ඥ (Mode 1)

1. "DSP upgrade" ȕǩȫȀǛ PC ƷȏȸȉȇǣǹǯƴǳȔȸ

ƠǇƢŵ

2. ஜೞƱPC ǛRS-232C ư੗ዓƠǇƢŵ

3. ஜೞƷᩓเǛλǕǇƢŵ

13

4. [SR7500 / SR8500]

Press ENTER, SURROUND MODE and T-MODE

buttons simultaneously more than 5 seconds to turn the

unit into Loading Mode.

[PS7500 / PS8500]

Press ENTER, SURROUND MODE and SLEEP buttons

simultaneously more than 5 seconds to turn the unit into

Loading Mode.

5. “LOADING MODE” will be shown on FLD.

6. Launch “UpgradeDSP.exe” on PC.

Note: yy_mm_dd is release date of software.

7. Click Port setting, and select the COM Port No.

4. ENTER, SURROUND MODE, SLEEP Ʒ3ƭƷȜǿȳǛӷ

଺ƴ 5ᅺˌɥ਀ƠዓƚƯ Loading Mode ƴƠǇƢŵ [PS7500

/ PS8500]

5. FL ȇǣǹȗȬǤƴ "LOADING MODE" ƱᘙᅆƞǕǇƢŵ

6. PC Ɣǒ "UpgradeDSP.exe" ǛȀȖȫǯȪȃǯƠƯឪѣƠǇ

Ƣŵ

දᚡ

දᚡ :ȕǡǤȫӸƷ yy_mm_dd ƸǽȕȈǦǧǢƷႆᘍଐǛ

ƋǒǘƠǇƢŵ

7. Port setting ǛǯȪȃǯƠŴCOM ȝȸȈဪӭǛᢠ৸ƠǇƢŵ

14

9. If the connection is made successfully, a dialog box say-

ing “Success to connect” appears and “CONNECTED” is

displayed on FLD.

10. Click Send the DSP codes button on the dialog box.

Progress status of updating will be shown on PC and

LOADING is displayed on FLD.

11. If updating is completed successfully, “COMPLETED” is

displayed on FLD. And a dialog box saying “Finished the

DSP code transmitting” appears.

12. Click OK and then Application is closed automatically.

13. Turn off the unit.

8. Set the Baud rate to 38400 then click Start communi-

cation button.

8. Baud rate Ǜ38400 ƴᚨܭƠŴStart communication Ǜǯ

ȪȃǯƠǇƢŵ

9. ᡫ̮੗ዓƴ঺ыƢǔƱɦᚡƷȀǤǢȭǰȜȃǯǹƕᘙᅆƞ

ǕŴFL ȇǣǹȗȬǤƴƸ "CONNECTED" ƕᘙᅆƞǕǇƢŵ

10. Send the DSP codes ǛǯȪȃǯƠǇƢŵǢȃȗȇȸ

ȈƷǹȆȸǿǹȐȸƕᘙᅆƞǕŴ

FL ȇǣǹȗȬǤƴƸ

"LOADING" ƕᘙᅆƞǕǇƢŵ

11. ǢȃȗȇȸȈƕ঺ыƢǔƱFL ȇǣǹȗȬǤƴ

"COMPLETED" ƱᘙᅆƞǕǇƢŵӷ଺ƴ"Finished the

DSP code transmitting" ƷȀǤǢȭǰȜȃǯǹƕᘙᅆƞǕ

ǇƢŵ

12. OK ǛǯȪȃǯƢǔƱᐯѣႎƴǢȗȪǱȸǷȧȳƕ᧍ơǇ

Ƣŵ

13. ஜೞƷᩓเǛЏǓǇƢŵ

15

Download Firmware for CPU (Mode 2)

1. Put the “CPU update” folder into anywhere on your PC’s

hard disc.

2. Connect PC and the unit with the RS-232C cable.

3. Insert a thin rot to the hole and push the switch (SW10)

inside to turn on the switch.

4. Turn on the power of the unit.

Note: When the unit is into boot mode, stand-by LED is

not lights up.

Hole of rear panel

SW10

CPU

ƷǢȃȗȇȸȈ૾ඥ

ƷǢȃȗȇȸȈ૾ඥ (Mode 2)

1. "CPU update" ȕǩȫȀǛ PC ƷȏȸȉȇǣǹǯƴǳȔȸƠ

ǇƢŵ

2. ஜೞƱPC ǛRS-232C ư੗ዓƠǇƢŵ

3. ኬƍొǛ̅ƍஜೞƷȪǢȑȍȫƴƋǔᆭƔǒǹǤȃȁ

(SW10) Ǜ਀ƠǇƢŵ

4. ஜೞƷᩓเǛλǕǇƢŵ

දᚡ

දᚡ : ஜೞƸȖȸȈȢȸȉƴƳǓŴStand-by LED Ƹໜ໊Ơ

ǇƤǜŵ

ȪǢȑȍȫƴƋǔᆭ

16

7. Click other ﬁ les... button in the dialog box to specify the

ﬁ le (SR8500_yymmdd.mot) to be uploading. yymmdd in

ﬁ lename is release date of software.

6. Click Set Ports, and select the COM Port No.

5. Launch "H8Download.exe" on PC.

H8FW2505

SR8500_yymmdd.mot

H8FW2505

5. PC Ɣǒ "H8Download.exe" ǛȀȖȫǯȪȃǯƠƯឪѣƠǇ

Ƣŵ

6. Set Ports ǛǯȪȃǯƠŴCOM ȝȸȈဪӭǛᢠ৸ƠǇƢŵ

7. other ﬁ les… ǛǯȪȃǯƠƯŴǢȃȗȇȸȈȕǡǤȫ

(SR8500_yymmdd.mot) Ǜᢠ৸Ơ᧏ƖǇƢŵ

17

8. Click Connect button. If the connection with the H8 µ-P

is successfully made, a dialogue box saying "Success to

the H8 micro processor connection" appears. (If the con-

nection fails, error message will appear.)

9. Click Send button to start update.

10. If the ﬁ rmware is updated successfully, a dialog box say-

ing "Finished the ﬁ rmware program sending” appears.

h82505_38400.inf

8. Connect ǛǯȪȃǯƠǇƢŵH8 u-P Ʊᡫ̮੗ዓƴ঺ыƢǔ

Ʊ"Success to the H8 micro processor connection" ƷȀǤ

ǢȭǰƕᘙᅆƞǕǇƢŵ ᡫ̮ƴڂ૗ƢǔƱǨȩȸȡȃǻȸ

ǸƕᘙᅆƞǕǇƢŵ

9. Send ǛǯȪȃǯƠǢȃȗȇȸȈǛ᧏ڼƠǇƢŵ

10. ǽȕȈǦǧǢƷǢȃȗȇȸȈƕ঺ыƢǔƱŴ"Finished the

ﬁ rmware program sending" ƷȀǤǢȭǰȜȃǯǹƕᘙᅆ

ƞǕǇƢŵ

18

11. Click Close button to close the application.

12. Disconnect Mains power cord.

13. Turn off the internal switch that has been turned on at

step 3.

14. Turn on the unit.

Firmware Version Check

To check the versions of the ﬁ rmware, see "Microprocessor

(CPU), DSP Version and FLD Segment Check Mode" in

"SERVICE MODE" section.

h82505_38400.inf

11. Close ǛǯȪȃǯƠƯǢȗȪǱȸǷȧȳǛ᧍ơǇƢŵ

12. ஜೞƷᩓเǛЏǓǇƢŵ

13. ৖᪯ 3ƷǹǤȃȁᲢSW10ᲣǛ਀ƠƯȖȸȈȢȸȉǛᚐᨊƠ

ǇƢŵ

14. ᩓเǛλǕǇƢŵ

ȐȸǸȧȳƷᄩᛐ

ǽȕȈǦǧǢƷȐȸǸȧȳǛᄩᛐƠǇƢŵᄩᛐ૾ඥƸ

"SERVICE MODE" ϋƷ"Microprocessor (CPU), DSP

Version and FLD Segment Check Mode"ǛӋༀƠƯƘƩƞƍŵ

Page is loading ...

Marantz SR7500/A1B User manual

This manual is also suitable for

Marantz SR7500/A1B User manual

Related papers

Other documents