zortrax M200 User manual

M200
Brand
zortrax
Model
M200
Type
User manual

This manual is also suitable for

Zortrax M200 is a robust and reliable 3D printer equipped with a heated bed capable of reaching up to 100°C, ensuring excellent adhesion and high-quality prints. Its user-friendly design, featuring a touchscreen interface, intuitive software, and automatic bed leveling, makes it accessible to both beginners and experienced users. With a build volume of 200 x 200 x 180 mm, Zortrax M200 accommodates various print sizes, allowing you to bring your ideas to life.

Zortrax M200 is a robust and reliable 3D printer equipped with a heated bed capable of reaching up to 100°C, ensuring excellent adhesion and high-quality prints. Its user-friendly design, featuring a touchscreen interface, intuitive software, and automatic bed leveling, makes it accessible to both beginners and experienced users. With a build volume of 200 x 200 x 180 mm, Zortrax M200 accommodates various print sizes, allowing you to bring your ideas to life.

Extruder Motor Replacement
SOURCE:
https://support.zortrax.com/extruder-motor-replacement/
page 1 / 22
Table Of Content
Unloading the Material 4
Unplugging the Power Cable 5
Material Guide Removal 6
Unplugging the Extruder Cable 7
Unplugging all Cables from the Extruder PCB 8
Unscrewing the Extruder PCB 9
Extruder Lower Printed Cover Removal 10
Unscrewing the Aluminum Extruder Cover 11
Unscrewing the Extruder Motor 12
Extruder Motor Removal 13
Extruder Motor Assembly, part 1 14
Extruder Motor Assembly, part 2 15
Extruder Aluminum Cover Assembly 16
Extruder Lower Printed Cover Assembly 17
Extruder PCB Assembly 18
Plugging all Cables to the Extruder PCB 19
Plugging the Extruder Cable 20
Material Guide Installation 21
Plugging the Power Cable 22
page 2 / 22
The extruder motor is responsible for loading the material into the hotend.
Therefore, if you can hear a clicking sound coming from the extruder motor during
the material loading or printing, or if the material gets blocked in the duct in the
extruder, at first you should carry out extruder motor maintenance. The
instructions are available in the manual: extruder motor maintenance.
If the maintenance work does not help, follow the steps from this manual to replace the
extruder motor.
The following manual shows the M200 repair work. For the M300, these procedures are
the same.
page 3 / 22
Unloading the Material
From the menu choose “Material” and then “Unload the material” option. The extruder
should start to heat up automatically. Once the extruder is hot, the motor will start to
unload the material.
page 4 / 22
Unplugging the Power Cable
Turn off the printer and unplug the power cable.
page 5 / 22
Material Guide Removal
Detach the material guide from the extruder cover. Next, separate the guide from the
extruder cable.
page 6 / 22
Unplugging the Extruder Cable
Detach the extruder upper printed cover and unplug the extruder cable.
page 7 / 22
Unplugging all Cables from the Extruder PCB
Unplug all the cables from the extruder PCB.
page 8 / 22
Unscrewing the Extruder PCB
Unscrew the two screws that secure the extruder PCB using a 2mm Allen key. Remove
the PCB from the extruder.
page 9 / 22
Extruder Lower Printed Cover Removal
Remove the extruder lower printed cover.
page 10 / 22
Unscrewing the Aluminum Extruder Cover
Unscrew the screws that securing the extruder aluminum cover on both sides of the
extruder. Separate the cover from the extruder motor.
page 11 / 22
Unscrewing the Extruder Motor
Unscrew the four screws that secure the extruder motor.
page 12 / 22
Extruder Motor Removal
Separate the extruder motor from the extruder block.
page 13 / 22
Extruder Motor Assembly, part 1
Reattach the extruder motor to the extruder block.
page 14 / 22
Extruder Motor Assembly, part 2
Secure the motor with the screws. Press the motor to the right side so that the bearing
rack is as close to the bearing as possible. Tighten the screws crosswise in the following
order: 1-4, 2-3.
page 15 / 22
Extruder Aluminum Cover Assembly
Reattach the extruder aluminum cover to the extruder and secure it with the screws.
page 16 / 22
Extruder Lower Printed Cover Assembly
Attach the extruder lower printed cover to the extruder.
page 17 / 22
Extruder PCB Assembly
Place the extruder PCB in its place and secure it with the two screws.
page 18 / 22
Plugging all Cables to the Extruder PCB
Plug all the cables in. Remember to arrange the cables so that they don’t get damaged,
e.g. by wrapping against each other.
page 19 / 22
Plugging the Extruder Cable
Plug the extruder cable in, and then attach the extruder upper cover to the lower cover.
MAKE SURE THE EXTRUDER CABLE IS PROPERLY PLUGGED IN.
page 20 / 22
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

zortrax M200 User manual

M200
Brand
zortrax
Model
M200
Type
User manual
This manual is also suitable for

Zortrax M200 is a robust and reliable 3D printer equipped with a heated bed capable of reaching up to 100°C, ensuring excellent adhesion and high-quality prints. Its user-friendly design, featuring a touchscreen interface, intuitive software, and automatic bed leveling, makes it accessible to both beginners and experienced users. With a build volume of 200 x 200 x 180 mm, Zortrax M200 accommodates various print sizes, allowing you to bring your ideas to life.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents