Huawei SmartAX MA5672 Quick start guide

Brand: Huawei

Model: SmartAX MA5672

Type: Quick start guide

SmartAX MA5672

Multi-service Access Equipment

Quick Start

1 Precautions

To use the device properly and safely, read the precautions carefully before using the device and

strictly observe these precautions when using the device.

Security warning and Precautions:



Do not look directly into the optical port without eye protection.



Keep the device out of the reach of children as the components or accessories may be

swallowed.



Install the device in strict compliance with the requirements of the supplier. Reserve a

space of at least 10cm above and around the device for heat dissipation. During the

installation, keep the device away from electric appliances that generate strong magnetic

or electric fields, such as microwave ovens, refrigerators, and mobile phones.



The power supply voltage of the device must meet the requirements on the input voltage

of the device.



Do not use any power adapters that are not in the standard configuration. Otherwise, the

device may be abnormal or unsafe.



Dry your hands before connecting or disconnecting cables. Stop the device and switch

off the power before connecting or disconnecting cables.



Do not place any object on the device, so that the device will not be damaged due to

overheating or deformation.



Prevent objects, such as metal, from entering the device through the heat dissipation

hole.



Switch off the power and disconnect all cables, including the power cable, optical fiber,

and network cable, during periods of lightning activities.



Do not lead the strength member of the optical fiber or other metal parts indoors. Do not

install telephone lines, network cables, power adapters or power adapter cables outdoors.

Adopting these measures will help prevent device damage and bodily injuries which are

especially prone during thunderstorms.



If an abnormality occurs, for example, liquid entering the device, smoke, unusual sound,

and smell, stop the device immediately, switch off the power, disconnect all cables (such

as the power cable, optical cable, and network cable) to the device, and contact the

authorized service center.



Do not disassemble the device without permission. In the case of a device fault, contact

the authorized service center.



Dispose of the packing materials, expired batteries, and old or abandoned devices in

accordance to local laws and regulations (recycling them is strongly recommended).



Do not change the structure, safety design, or performance design of the device without

prior authorization.

Fire warning and Precautions:



The equipment needed to be far away from the large heat source, naked fire, and large

power equipment, such as electric heater, candles, hair dryer, avoid introducing safety

risk.



Near power lines - equipment or equipment, such as aging or aging cable plug board and

other facilities, please timely replacement, to avoid the introduction of safety risk.

2 Installing the MA5672

Horizontally placed on a workbench

The following figure shows the MA5672 horizontally placed on a workbench.

Mounted onto a wall

The MA5672 can be mounted horizontally or vertically onto the wall.

Step1

Mark the positions of two holes (with a spacing of 150mm) used for mounting the

MA5672.

Step2

Select a proper drill according to the outer diameter of the screws. Use a hammer drill to

drill the marked positions on the wall. Then clean the wall and install two expansion

bolts.

Step3

Use a screwdriver to fasten the screws (size: M3) into the expansion bolts, leaving the

heads of the screws 3mm over the wall. Then install the MA5672 to the screws.

Horizontal Installation Vertical Installation

1. Do not install MA5672 outdoors or on the outdoor cabinets.

2. The figures shown in this document may differ from the actual product, but the

difference does not affect the functions of the product.

3 Connecting Cables

Cable connections between the MA5672 and Other devices

USB

Optical port in the wall

TV-set

IP set-top box(STB)

Power adapter

Telephone set

Fax machine

Refer to the preceding cable connections of each product and select the

following corresponding steps to connect the MA5672.

Step1

Use an optical fiber to connect the OPTICAL port on the MA5672 to the optical port in

the wall.

The optical connector connected to the OPTICAL port is SC/APC.

Step2

Use a network cable to connect the LAN port to the Ethernet port of the PC or IP STB.

Step3

Use a telephone cable to connect the TEL port to the telephone set or fax machine.

Step4

Use a power cable to connect the POWER port to the power adapter.

Step5

The USB port can be inserted the data card.

Step6

Press the ON/OFF power button.

4 Description of LEDs

Table 4-1 LED status indications 1

LED

Status

Description

TEL1～TEL4

Always on

The connection to the voice server is

set up.

Blinks quickly (twice per

second)

The connection to the voice server is

set up and the telephone is in the

off-hook or ringing state.

Blinks slowly (once two

seconds)

The ONU is registering with the voice

server.

Off

The connection to the voice server is

not set up.

LAN1～LAN4

Always on

The Ethernet connection is in the

normal state.

Blinks

Data is being transmitted on the

Ethernet port.

Off

The Ethernet connection is not set up.

LOS

See Table 5-2.

PON

See Table 5-2.

USB

Always on

USB port is enabled.

Blinks

USB port data transmission.

Off

USB port is disabled.

POWER

Green: always on

The device is powered on.

Off

The power supply is cut off.

PON and LOS are GPON LEDs. The status of PON and LOS reflects the connection between

MA5672 and the optical line terminal (OLT). The following table describes the status of the PON

and LOS LEDs.

Table 4-2 LED status indications 2

No.

LED Status

Description

PON

LOS

Off

The MA5672 is disabled by the

OLT.

Off

The connection between the

MA5672 and the OLT is not set

up.

Blinks quickly

(twice per second)

The MA5672 is attempting to set

up a connection to the OLT.

Always on

The connection between the

MA5672 and the OLT is set up.

Off

The Rx optical power of the

MA5672 is normal.

Blinks slowly

(once two

seconds)

The Rx optical power of the

MA5672 is lower than the optical

receiver sensitivity.

Blinks quickly

(twice per second)

Blinks quickly

(twice per second)

The OLT detects that the device is

a rogue ONU.

5 FAQs

The LOS indicator is blinking.

 When the LOS indicator blinks slowly, check whether the pigtail fiber is connected normally

and whether the optical connector is contaminated.

 When the LOS indicator blinks quickly, check whether the MA5672 transmits optical signals

normally.

The PON indicator is off.

 Check whether the optical fiber is properly connected to the OPTICAL port.

 The MA5672 fails to register with the OLT. Contact the service provider for help.

How to reset the MA5672?

 Press the RESET button by using a needle-type object.

How can I restore factory defaults?

 Press RESET button by using a needle-type object for longer than 10s to restore factory

defaults and reset the MA5672. If the indicator is off and then is lit, the system restarts

successfully.

6 Technical Specifications

Item

Specifications

Dimensions (L x W x H)

260mm x 180mm x 30mm

Weight

0.843kg

Working temperature

-40ºC - +55ºC , the device can be started at -25 ° C.

The minimum temperature.

Working humidity

5% - 95% (non condensing)

Declaration on Hazardous Substances in Electronic

Information Products

Parts

Hazardous Substances

Cr6+

PBB

PBDE

Mechanical part

○

Board/circuit module

○

Signal cable

○

Cable connector

○

Power adapter

○

Auxiliary equipment

○

○: Indicates that the concentration of the hazardous substance contained in all the homogeneous

materials of this part is below the limit requirement of the SJ/T 11363−2006 standard.

×: Indicates that the concentration of the hazardous substance contained in all the homogeneous

materials of this part is above the limit requirement.

1. Shell and mechanical part: the steel, aluminum or copper lead.

2. Board / circuit module:

 PCB pad lead.

 Board ceramic / PEG / mica capacitor and inductance lead.

 The internal clock oscillator resistor lead.

 Lead - optical transceiver module internal optical glass and optical joints.

 Lead RF coaxial connector.

 With a high temperature solder used to lead content of more than 85% - transformer.

 Lead inductance, for optical glass.

 High temperature solders welding - use of a transistor chip lead solder.

 The use of ceramic resistors, ceramic lead.

 The board IC, power supply and other components such as lead pin and solder.

3. Signal lines: one of the steel, aluminum, copper and other alloy materials in lead.

4. Cable connector: most of the connector metal shell, terminal and other lead, lead, etc..

5. Power adapter: internal lead.

6. Supporting equipment in the circuit board lead, with the above first, second.

Warranty Card

Thank you for choosing Huawei Technologies Co., Ltd. To get better services, please

read this warranty card carefully, fill in the required information, and preserve this card

in good condition.

PERSONAL OR COMPANY

FULL NAME

Address/Postal Code

Telephone Number

Product Type

Product Serial Number

Purchase Date

Invoice Number

Dealer's Name

Dealer's Address

Dealer's Telephone

Preserve well. No reissue.

Dealer's Seal

Limited Warranty

Subject to the exclusions contained below, Huawei Technologies Co., Ltd.

(hereinafter referred to as Huawei) warrants its access terminals (“Products”) to

be free from defects in materials and workmanship under normal consumer usage

for one year from the date of purchase of the product ("Warranty period"). During

the warranty period, a Huawei authorized service partner shall remedy defects in

materials and workmanship free of charge.

Special Notice:

1. The warranty card shall be applicable only after being stamped by the dealer.

2. The warranty card must be preserved in good condition and free of any

scratch or alteration.

3. To claim such service for defects that are not included in the following

exclusion terms, the warranty card and the invoice that records the product

serial number shall be presented to a Huawei authorized service partner.

Exclusions:

In any of the following cases, the warranty card becomes unenforceable or

inapplicable without prior notice:

1. The defects are caused by improper handling in transportation and assembly.

2. The defects are caused by the fact that the product is dismantled or altered by

anyone that is not from a Huawei authorized service partner.

3. The defects are caused by the fact that the product is used in a harsh

environment that is not suitable for the operation of the product.

4. The defects are caused by any force majeure including but not limited to fire,

earthquake, lightning and tsunami.

5. The defects are caused by the fact that the product is used or handled

improperly, roughly or not as instructed in the applicable User Guide.

6. The normal wear and tear, including but not limited to the normal wear and

tear of the shell and the power module, shall not be covered by the limited

warranty.

7. The warranty card is altered or illegible, or the product serial number

recorded on the warranty card is inconsistent with the actual one imprinted or

labeled on the product.

In any case that is not covered by this limited warranty or should the warranty

expire, Huawei shall charge for the service(s) claimed for the products if the

product is still remediable. Huawei preserves the right for interpretation of this

limited warranty.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website: http://www.huawei.com

reserved.

No part of this document may be reproduced or transmitted in any form or by any means without

prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other

trademarks and trade names mentioned in this document are the property of their respective

holders.

Notice

The information in this document is subject to change without notice. Every effort has been made

in the preparation of this document to ensure accuracy of the contents, but all statements,

information, and recommendations in this document do not constitute a warranty of any kind,

express or implied.

Issue：01（20160112）

Huawei SmartAX MA5672 Quick start guide

Huawei SmartAX MA5672 Quick start guide

Huawei SmartAX MA5672 Quick start guide

Related papers

Other documents