RCA J32530YX58CJ6 User manual

Brand: RCA

Model: J32530YX58CJ6

Type: User manual

This manual is also suitable for

WARNING

To reduce the risk of fire or shock

hazard, do not expose this TV to

rain or moisture.

RISK OF ELECTRICSHOCK

DO NOT OPEN

To reduce the risk of electric shock, do not remove cover

(or back). No user serviceable parts inside. Refer servicing

to qualified service personnel.

This symbol indicates "dangerous A

voltage" inside the product that

presents a risk of electric shock

or personal injury.

This symbol indicates

important instructions

accompanying the product.

Cautions

Note to Cable TV Installer

CAUTION: To prevent electric shock, match wide blade of plug to

wide slot, fully insert.

ATTENTION: Pour eviter les chocs electriques, introduire la lame la

plus large de la fiche dans la borne correspondante de la prise et

pousser jusq0 au fond.

Refer to the identificationlrating label located on the back panel of your product for its

proper operating voltage.

FCCRegulations state that unauthorized changes or modifications to this equipment

may void the user's authority to operate it.

Caution: If fixed (non-moving) images are left on the screen for long periods, they may

be permanently imprinted on the picture tube. Such images include network Iogos,

phone numbers, and video games. This damage is not covered by your warranty.

Extended viewing of channels displaying these images should be avoided.

This reminder is provided to call your attention to Article 820-40 of the National

Electrical Code (Section 54 of the Canadian Electrical Code, Part I) which provides

guidelines for proper grounding and, in particular, specifies that the cable ground shall

be connected to the grounding system of the building as close to the point of cable

entry as practical.

Product Registration

Please fill out the product registration card and return it immediately. Returning the card allows us to contact you if needed.

Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and

model numbers in case you need them. The numbers are located on the back of the television.

Model No.

Serial No.

Purchase Date:

DealedAddresgPhone:

QUICK GUIDE TO THE TV ........................................... 3

Startup .............................................................................................. 3

Understanding the Menus ............................................................... 6

Using Master and Basic Menus ................................................. 7

USING THE REMOTE .................................................... 9

Types of Remotes .............................................................................. 9

Master Remote Buttons (CRK17TD1) ............................................ 10

Universal Remote Buttons (CRK76TK1) ......................................... 12

Using the iNPUT Button ................................................................. 14

Using the SYSTEM Button .............................................................. 14

Universal Remote Features ............................................................ 15

Controlling Components ......................................................... 15

PIP(Picture-In-Picture) Operation ................................................. 16

Using the PIP Feature .............................................................. 16

MASTER MENUS .......................................................... 19

Audio Menu .................................................................................... 19

Picture Quality Menu ..................................................................... 21

Channel Menu ................................................................................ 22

Access& Power Options ................................................................. 24

Closed Captioning Menu ............................................................... 27

Time and Timers Menu ................................................................... 28

Parental Controls Menu ................................................................. 30

Locked/Unlocked ...................................................................... 30

V-Chip Movie Rating Limit ...................................................... 31

V-Chip TV Ratin9 Limit ............................................................ 32

TV Age-Based Ratings .............................................................. 33

V-Chip Unrated Program Block ............................................... 38

Channel Block .......................................................................... 38

Password ................................................................................... 39

Menu Language ............................................................................. 39

PCVideo Input Controls ................................................................. 40

Using the PCVideo Input Controls ......................................... 41

BASIC MENUS ............................................................. 43

Channel Guide ......................................................................... 43

Menu Language ....................................................................... 43

Closed Captioning Menu ......................................................... 44

Time and Timers Menu or Sleep Timer ................................... 44

Picture Presets Menu ............................................................... 45

Audio Processor Menu ............................................................. 45

Parental Controls Menu .......................................................... 45

PCVideo input Controls .......................................................... 46

CONNECTIONS ........................................................... 47

Back of TV Jacks ............................................................................. 47

PCINPUT Connection ..................................................................... 47

Antenna or Cable Connection ....................................................... 48

Cable Box Connections .................................................................. 49

Cable Box and VCR Basic Connection ........................................... 50

VCR Basic Connection .................................................................... 50

Cable Box and VCR Advanced Connection ................................... 51

VCR Intermediate Connection ....................................................... 51

VCR Advanced Connection ............................................................ 52

Audio Connection .......................................................................... 52

REFERENCE ................................................................... 53

Front Panel ..................................................................................... 53

Status Displays ................................................................................ 54

Troubleshooting ............................................................................. 55

FCCInformation ............................................................................. 58

Warranty ......................................................................................... 59

INDEX ......................................................................... 60

STARTUP

The steps below will get your TV connected and ready for watching. For

more details, refer to the sections listed.

CAUTION:

If you choose to use a stand with your TV, take precautions that the

stand or other furniture the TV is placed on is properly located and

of adequate size and strength to prevent the TV from accidentally

being tipped over, pushed off, or pulled off. This could cause

damage to the TV and/or personal injury.

1. Hook up Your TV

See the "Connections" section for details.

Hook up any antennas, cables or other equipment to your TV before you

follow the steps below.

2. Plug in the TV

Plug the cord into a properly grounded outlet. See the Safety

Information sheet packed with your TV for more information.

3. Obtain a Master Remote

A master remote (CRK17TD1) is required for setup of many of the TV's

features. Most of the operating instructions in this manual are

explained using the master remote. (A master remote can be purchased

from your distributor. See the "Using the Remote" section for details.)

4. Put Batteries in the Remote

1. Pull off the cover of the battery compartment.

2. Place the two AAA batteries into the remote as shown at right,

matching the + and- end of each battery in the compartment.

3. Replace the coven

5. Turn on the TV

Press POWER on the remote.

Press POWER on the TV.

Power

&Power

6. Use Point and Select

You only need to know one rule when using the remote to access on-

screen menus and control panels: point and select. The point and select

method has two steps.

1. Point to a menu item using the arrow buttons on the remote.

To point up or down, press the up or down arrows. To point left or

right, press the left or right arrows.

2. Select a menu item by pressing MENU or OK.

Selecting an item tells the TV's menu system to go ahead and make

the change or go to the place you have indicated. To quickly select a

numbered menu option, just press the corresponding digit button

on the remote control.

Arrow, OK

and MENU

buttons

Digit buttons __ ,0 _0,0

7. Place All Available Channels Into Memory

See the Channel Menu portion of the "Master Menus" section for

details.

1. Press MENU on the remote control, then select Channel, then Auto

Channel Search.

2. Select which channel list you'd like to find channels for (List A isthe

default).

8. Set the Time

To set the time, select automatic setting of the time, or to prevent

viewers from accessing the Current Time and Schedule functions, see the

Time and Timers Menu portion of the "Master Menus" section.

If the control panel is not set to the |

current time, use the arrow and digit J

buttons on the remote control to make

changes.

You can also enter numbers by using the

up and down arrows on the remote.

9. Use the Clone Box

If several TVs need to be programmed with the same menu settings, an

optional clone box can be used to copy all of the menu settings from

one TV into other TVs to reduce installation time. Information can be

both downloaded to and uploaded from the clone box using the DSCI

port on the TV's back panel or using the IR sensor. Refer to the clone

box owner's manual for operating instructions.

Your setup is complete! Please read the "Understanding the Menus" description that

follows before customizing menu options. Instructions on operating more advanced

features are given throughout the rest of this manual.

UNDERSTANDING THE MENUS

This television displays two levels of menu system: master and basic.

The master menus are accessible by pressing MENU on the master

remote (CRK17TD1). The master Main menus will always display the

eight choices shown below. A ninth choice, PCVideo Input Controls, will

appear if the PCinput is selected.

The master Main menu. If the PC input is not selected, the

ninth item wil! not appea_

The basic menus are accessible by pressing MENU on a basic remote

(CRK17TC1 or other remote) or the front panel. The choices available on

the basic menus and control panels will vary depending on limits set by

the master user and the input selected. For more information on the

effects of master user choices on the basic menu and basic user

functionality, see the "Basic Menus" section and the description of the

Access and Power Options menu in the "Master Menus" section.

The basic Main menu. The choices available in this menu

wil! change according to limits set by the master use_

USING MASTER AND BASIC MENUS

Menus and choice lists use the point and select rule to navigate, but

control panels use a variety of methods to adjust features on your TV.

The following pages detail how to use these controls to customize the

functions of your TV.

The first menu is called the Main menu. Press MENU on the remote

(master remote for master menu; basic or universal remote for basic

menu) or on the front panel (basic menu) to bring up the Main menu:

Menu choices take you to another menu or a control panel. There are

two ways to select a choice in a menu:

• Point with the arrows and then select with MENU or OK.

• Pressa number button on the remote. For example, in the master

Main menu press 3 to go straight to the Channel menu.

Exiting a menu

There are three ways to exit a menu. Not all methods work in all menus:

• Point to Exit and press MENU or OK.

• Press0 on the remote.

• PressCLEAR. The on-screen displays are cleared from the screen and

you return to TV viewing.

Sliders

Sliders are used to make adjustments to a particular control. To use a

Slider in a menu:

1. Pressthe up or down arrow to select the slider control for the

feature you want to adjust.

2. Pressthe right or left arrow to adjust the indicator line on the slider.

Arrow

and OK I I_ _

buttons O_

0°08'

MASTE_

Numeric Entry

A numeric entry control panel is used to enter numbers or letters. A

pointer appears underneath the column you are changing.

1. Use the digits to enter a number in the column above the pointer.

2. Pressthe right arrow to move to the next column, then use the

digits to enter a numben

3. When you have finished entering information, press MENU or OK.

Choice Lists

Choice lists are used to choose a particular setting from a list. When the

choice list appears, the highlighted item is the one that is currently

selected, or "in use."

Point to a choice on a menu and press MENU or OK to select that choice.

Pressthe corresponding digit button on the remote to highlight and

select in one step. You will then return to the previous screen.

Now that you know how to access the menus and adjust the control

panels, the rest of this manual provides explanations of master and basic

menu items, organized in order of their location on the Main menu.

TYPES OF REMOTES

Master setup remote controls and universal remotes are available from

your RCA distributor. Descriptions of the remote buttons and how they

work are on the next pages. Except as otherwise specified, the master

remote is the remote described throughout the manual for operating

the TV and setting up the TV's features.

Master Setup Remotes

The master remote (CRK17TD1) allows control of all of the TV's menus.

It is used to customize the TV's functionality for specific users or specific

situations. These remotes are available from your RCA distributor.

Universal Remotes

These remote controls offer basic control of the television within the

limits specified through the master remote. In addition, they can be

programmed to control other components (such asVCRs). Extra remotes

are available from your RCA distributor.

o°0 S

MASTER

Master Remote CRK17TD 1

DD k Tpc

q C>

9_9

,0,0 _0

40 O 60

O o0 o0

8:) {i]_ !]D

OOOO

Universa! Remote CRK76TK1

If you cannot locate your remote you can |

use the front panel of your TV to operate J

the TV's basic features. See the

"References" section for more information.

MASTER REMOTE BUTTONS (CRK17TD1)

CC (Closed Captioning)

Brings up the Closed Caption Display. Subsequent presses change the

display mode.

POWER

Turns the TV on or off.

SLEEP

Displays the Sleep Timer control panel, which allows the user to set a

time for the TV to turn itself off.

MOL

(Volume up or down)

Raisesand towers sound (untess Volume Hotd ison) and displays the

Volume Control slider.

SYSTEM

This button allows the remote to change between TVl and TV2 mode. It

also allows access to system-defined functionality, when available. See

the description later in this section for more details.

CHAN

(Channel up or down)

Scans up and down through channels in the TV's memory.

MUTE

Turns the TV sound to its minimal level.

GO BACK

Selects the last selected channel or video input and displays the Status

Display.

GUIDE

Displays or clears the Channel Guide (when not in the menu system).

Arrow buttons and OK

Use the arrow buttons to highlight your choices and navigate within the

menu system. Use the OK button to select your choice.

INFO

Displays or clears the Status Display.

Brings menus to the screen and moves from menu to menu.

CLEAR

Clears menus and displays from the screen.

CC POWER SLEEP

/1 GUIDE INFO

MENU CLEAR

INPUT RESET

MASTER

Digit Buttons (0-9)

Selects an available channel number or numbered menu option.

Two digits must be pressed for each channel. Press0 then 6 for channel 6.

For three digit channels, press and hold 1 until 1-- appears on the screen.

Then press the other two digits.

INPUT

Selects between TV (channels 01-125) and other available inputs. See the

description later in this section for more details.

RESET

Returns the picture to the original settings and displays the Picture Presets

choice list.

UN IVERSAL REMOTE BUTTONS (CRK76TK1) LED

ON-OFF Turns the device you are controlling on or off. When pressed

twice within two seconds, all devices that are on will be turned off (this

feature only works with most RCA, GE, and PROSCAN products). You can

also use the ON.OFF button on the front panel of the TV to turn it on

or off.

VCR1 When programmed, tells the remote to control the VCR.

TVI Tells the remote to control TVI. See the description under Access

& Power Options in the "Master Menus" section for more information.

DVD Tells the remote to control the DVD player. Note that this button

is only functional with RCA, GE, and PROSCAN DVD players.

VCR2 When programmed, tells the remote to control a second VCR.

LED This light turns red at each valid button press. When

programming the remote control, it flashes or turns on or off to indicate

programming status.

TV2 Tells the remote to control TV2. See the description under Access

& Power Options in the "Master Menus" section for more information.

SAT-CABLE When programmed, tells the remote to control a digital

satellite receiver or cable box.

MUTE Reduces the TV's volume to its minimum level. Press again to

restore the volume.

SKIP (Commercial Skip) If you press this button before you change

the channel, the TV waits 30 seconds then takes you back to the original

channel. Each press adds 30 seconds to the skip time. Press CLEAR to

cancel. Also functions as RESETin some menus.

CH + (up) I- (down) Use to scan up and down through the channels in

the current channel list. You can also use the CH +/- buttons on the TV's

front panel to change the channel.

VOL <(down) and >(up) Adjusts the audio volume of the TV.

CC (Closed Captioning) Brings up the Closed Caption Display.

Subsequent presses change the display mode.

SYSTEM This button allows access to system-defined functionality,

when available. See the description later in this section for more details.

GO BACK Selects between the last two selected channels or inputs. In

the menu system, returns you to the previous screen.

GUIDE Displays or clears the Channel Guide (when not in the menu

system).

INFO Displays or clears the Status Display.

Arrows Use the navigation arrows to move the on-screen highlight

up, down, left, or right. Using the arrows to highlight a menu item is

also called "pointing."

CC _j GO BACK

GUEDE INFO

MENU CLEAR

WHO(_JT00 ANTENNA

R[VERSE PLAY FORWARD

R_CORD STOP PAUSE

P_P SWA_ CHCTRL R_SET

u n I V e _ s _ I

OK Selects the highlighted choice.

MENU Displays the basic Main menu. If you are already in the menu

system, press OK or MENU to select a highlighted choice. When you are

using the remote control to operate an RCA, GE, or PROSCAN VCR (and

the remote is in VCR mode), the MENU button functions as a PROGRAM

button.

CLEAR Removes the on-screen displays and returns you to normal

viewing.

Digit Buttons (0 - 9) Selects an available channel number or

numbered menu option. Two digits must be pressed for each channel.

Press0 then 6 for channel 6. For three digit channels, press and hold 1

until 1-- appears on the screen. Then press the other two digits.

WHO*INPUT Selects among the possible input choices. See the "Using

the Input Button" description later in this section for more information.

ANTENNA In VCR mode, functions as a TV/VCR input button.

Transport Buttons (REVERSE, PLAY, FORWARD, RECORD, STOP,

PAUSE) When programmed, these buttons are used to control an

auxiliary device, such as a VCR or laserdisc player. Some of these buttons

are also used when viewing the PC input.

PIP (Picture-In-Picture) Brings up the PiP (Picture-In-Picture) window.

PressPiPagain to remove the window. When Alternate with PIPhas

been selected in PIP Closed-Caption Display, the TV will display closed

captioning in the PIP window at the second press of the PIP button.

SWAP Switches, or "swaps," the video from the PIPwindow with the

main picture.

CH CTRL (Channel Control) Lets you switch channel control between the

PIPwindow and the main picture. To determine whether you are

controlling he PIP window or the main picture, bring up the Status

Display by pressing INFO. The yellow channel number is the one you are

controlling.

RESET Displays the Picture Presets choice list. See the description of the

Picture Quality menu in the "Master Menus" section for more

information.

Entering certain channel numbers

automatically selects specific inputs:

Channel Input

126 VID

127 S-VID

128 PC

ISee the description of the PIP feature |

later in this manual for more information J

about using PIR

USING THE INPUT BUTTON

In addition to a cable or antenna signal, you might have VCR, DVD, PC,

Laserdisc, or other signals coming in to your TV (not all inputs available

on all models). Use the INPUT or WHO.INPUT button to select the

desired signal source.

1. Make sure that the component you want to view is turned on. If

you are using a remote control with component buttons (TV, VCR,

etc.) press TV to place the remote in TV mode.

2. Press INPUT until you have selected the desired input source.

Inputs and On-screen Displays

The Status Display shows which input signal(s) is selected. The following

table shows which display term usually corresponds with which input.

See Auto Tuning under the Channel Menu description in the "Master

Menus" section for more information on naming inputs.

Input Signal I"V Display

ANTENNA/CABLE jack (channel number)

A/V jacks VID

S-VIDEO jack SVID

PC INPUT PC

<3©D

INPUT button -- '_ 0O _'

USING THE SYSTEM BUTTON

When the television isconnected to an interactive system or similar

device, the SYSTEM button allows you to access system programming or

other special functionality through the DSCl jack (formerly called

"Smartplug").

When using a master remote, the SYSTEM button can also allow

independent remote control of two TVs. Once you have specified TVl or

TV2 status for the TVs (see the Access and Power Options description in

the "Master Menus" section), follow these steps to tell the remote

which TV you want to operate:

1. Simultaneously press and hold the SYSTEM button and 1 (for TVl)

or 2 (for TV2).

2. After three seconds, release the buttons. The specified TV should

now respond to that remote.

3. To control the other TV, simply repeat the process using the other

(1 or 2) button.

SYSTEM button --

1and 2

buttons

q©D

000 S

MASTER

UN IVERSAL REMOTE FEATURES

The CRK76TKI remote can be programmed to control most brands of

remote controllable components. The remote is already programmed to

control most RCA, GE and PROSCAN components; it may need to be

programmed to control other manufacturers' components.

You do not have to program the remote to control two TVs,

simply use the TV1 and W2 buttons. See Access & Power Options

in the "Master Menus" section for more information.

Testing the Universal Remote

To determine whether the universal remote control needs to be

programmed, turn a component on, such as a VCR, point the remote at

the VCR, and press the VCR button. Then press ON.OFF or CH ^Iv to see

if the VCR responds to the remote commands. If not, the remote needs

to be programmed.

Programming the Universal Remote

I. Turn on the component to be programmed.

2. At the end of this section, look up the code list that corresponds to

the component type and brand.

3. On your remote control, press and hold the component button you

want to program.

4. Enter one four-digit code from the code list.

5. Release the component button, and then press ON,OFF to see if the

component responds to the remote control commands. If it doesn't,

try pressing the component button and then ON,OFF again.

6, If you get no response, repeat these steps using the next code listed

for your brand, until the component responds to the remote

control. If it does respond, you are ready to control that component

with your universal remote.

CONTROLLI NG COMPONENTS

Once the remote has been programmed successfully, you are ready to

use it to control your components. To operate the component:

1. Pressthe component button (TVl, VCR1, DVD, VCR2, TV2, or

SAT.CABLE) to put the remote into that component's mode.

2. PressON.OFF to turn the component on or off.

3. Use the remote control buttons that apply to that component.

• If your remote is programmed to control a VCR, you only need to

press the RECORD button to begin recording from video.

(This remote control may not operate all

models of all brands.

ON,OFF

_¢ _ GO BACK

o0 o0

REV_RS_ PAY ORW&_D

R_CORD _ @gA SE

PP SW&_ CHC1RL RISE1

000{3

_n_versal

(

)

The RESETbutton on this remote |

functions the same as the Master remote

RESETor Basic remote SKiP button.

Modes of Operation

Because this universal remote can control

several different components (PC, VCR,

cable box, etc.), it uses operational modes

triggered by the component buttons. If

you want the remote to control TV1, you

must press the TV1 button to put the

remote into TV1 mode first.

PIP (PICTURE-IN-PICTURE) OPERATION

The PIP(Picture-In-Picture) feature lets you display a second, smaller

picture on top of the main picture.

Your TV is equipped with asingle tuner that can select one cable or off-

air television signal. The PIP feature on your TV requires asecond video

source (like a VCR, PC, or satellite receiver), to supply the second picture

to the screen. The second video source must be connected to the TV

through the video, S-Video, or PC INPUT jack. Remember to also

connect audio cables if necessary. See the connections on the next page,

or in the "Connections" section for examples of PIP-capable connections.

Main picture

Main picture input display

PIP window

PIP input display

USING THE PIP FEATURE f

Although PIP can be used in different ways, this basic PIP scenario should |

get you started. While watching the TV, follow these steps to use your LVCR to supply the picture for PIR

Pressthe PIP button on the remote. The PIP window appears on the

screen, showing the same image as the main picture.

Turn on the VCR (make sure it is properly connected).

Pressthe TV button, then press CH CTRL until the PIP input display is

selected (yellow).

PressWHOalNPUT until you see the VCR signal (usually VID)

displayed in the PIP input display. The PIPwindow should display the

channel selected on the VCR.

To select the PIP window's channel, you need to select the channel

on the VCR because that is the signal source for the PIP picture.

Select the channels using the VCR front panel, VCR remote, or by

pressing the VCR button on the remote to get into VCR mode, then

use the remote to select channels. (This last method requires that

the remote be programmed, see the instructions earlier in this

section.)

Use the CH CTRL button, the WHOalNPUT button, and the Arrow

and SWAP buttons to adjust the two pictures.

Refer to the description of the PIP,SWAP |

and CH CTRL buttons, earlier in this J

section, for more information.

IAny rating limits that are set will apply to |

both the PIP window and the main J

window.

You can program the TV to automatically

tune to a signal input when you press a

component button. This isa quick way to

select the correct video input channel for

the PIP window. See the descriptions of

Auto Tuning (in the "Main Menus"

section) and Programming the Remote,

earlier in this section.

PIP Problems?

PIPrequires that a second video source, like a VCR, PC,or satellite receiver, be connected to the TV with a second

connection (other than the primary cable or antenna connection). An example connection is pictured below. See the

"Connections" section for illustrations of other PIP-capable connections.

......... First video input source

_ Second video input source

VCR=

First video input source

....... Second video input source

1@@@],.

Connection with VCR Connection with PC

Remote not responding Make sure the remote is in the right mode. For example, once you turn on the VCR with the

VCR1 button, you can't swap the pictures until you put the remote in TV mode by pressing the TV button.

No signal or bad reception Most VCRs and satelEte receivers have an antenna or TV/VCR button. If your cable or

off-air antenna goes into your VCR or satellite receiver then into your TV, try pressing the antenna or TV/VCR button on

the front of the component.

Tip: If programmed to control your VCR, the ANTENNA button on the remote acts as a TV/VCR button in VCR mode.

PIP window and main window show same image Check the connections. If you use a cable box, you may need

extra equipment. Contact you cable company for more information.

When I change channels, both windows change Make sure the input you want to change is active before trying

to change it. See also "The component button doesn't work" below for more tips.

Closed Captioning is in wrong window (main vs. PiP) Closed Captioning is set for the window (main or PIP), not

the image source. When you swap, Closed Captioning will remain in the same window although the signals swap.

The component button doesn't work Your remote may need to be programmed to control components (see

description in the "Using the Remote" section).

If your remote is programmed, make sure that A/V signals are set to auto tune to the VID channel, S-Video signals are

set to auto tune to the SVlD channel, and PC signals are set to auto tune to the PCchannel. Setting them to CH3 or CH4

may cause problems.

That component's switch may be set for the wrong channel. Check to make sure the input source setting matches the

switch setting on the component (usually on the back panel).

kv£eJ,'| Motorola ........................................................................2021,2131

MTC .....................................................................2002, 2013, 2026

Admiral .....................................................................................2131 Multitech ............................2002, 2013, 2016, 2026, 2063, 2061

Adventura .................................................................................2026 NEC ...............................................2009, 2010, 2011,2016, 2018,

Aiko ...........................................................................................2027 ..................................2068,2064,2076,2078,2079,2111,2123

Aiwa ................................................................................2002, 2026

Akai ................2003, 2004, 200& 2007, 2008, 2111,2112, 2113

American High ........................................................................2021

Asha ...........................................................................................2013

Audio Dynamics ..........................................................2009, 2010

Audiovox ..................................................................................2014

Bell & Howell ...........................................................................2011

Beaumark .................................................................................2013

Broksonic ......................................................................2012, 2026

Calix ..........................................................................................2014

Candle ......................2013, 2014,2015, 2016, 2017,2018, 2019

Canon ..................................................................2021, 2022, 2114

Capehart ........................................................................2020, 2110

Carver .......................................................................................2062

CCE ................................................................................2027, 2061

Citizen ...........2013, 2014, 2016, 2016, 2017, 2018,2019,2027

Colortyme ...............................................................................2009

Colt ............................................................................................2061

Craig .........................................................2013, 2014, 2023, 2061

Curtls-Mathes ........................................2000,2002, 2009, 2013,

..............................................2016,2018, 2021, 2022, 2024, 2116

Cybernex ..................................................................................2013

Nikko ..........................................................................................2014

Noblex .......................................................................................2013

Olympus ....................................................................................2021

Optimus ..........................................................................2014, 2131

Optonica ....................................................................................2096

Orion .........................................................................................2035

Panasonic ............................2021,2022, 2109, 2126, 2126, 2127

Pentax ............................................2016, 2066, 2066, 2107, 2120

Pentex Research ......................................................................2018

Philco .........................................................2021, 2022, 2062, 2063

Philips ........................................................2021, 2062, 2096, 2124

Pilot ............................................................................................2014

Pioneer ...........................................2010, 2065, 2080, 2081, 2123

Portland ....................................................2016, 2017, 2019, 2110

PROSCAN .....................................................................2000, 2001

Protec .........................................................................................2061

Pulsar ..........................................................................................2104

Quarter .....................................................................................2011

Quartz ........................................................................................2011

Quasar .................................................................2021, 2022, 2125

RCA ...............................................2000, 2001, 2003,2013, 2021,

.........................2056, 2056, 2082, 2083,2084,2085, 2086,2087,

Daewoo ...... 2015, 2017, 2019,2026, 2026, 2027, 2028, 2110 ........................2088, 2089, 2090,2091, 2107, 2116, 2120, 2125

Daytron .....................................................................................2110

Dbx .................................................................................2009, 2010

Dimensia ...................................................................................2000

Dynatech .......................................................................2002, 2026

Electrohome .................................................................2014, 2029

Electrophonic ..........................................................................2014

Emerson .............................................................2002, 2012,2014,

.........................2015, 2021, 2024, 2025,2026,2029, 2030,2032,

............2033, 2034, 2035,2036, 2037, 2038, 2039, 2040, 2041,

• 2042, 2044,2046, 2047, 2066, 2105, 2113, 2116,2117, 2130

Fisher .............201I, 2023, 2048, 2049, 2060, 2051, 2052,2118

Fuji ..................................................................................2021, 2119

Radioshack/Realistic ...............................2002,2011,2013,2014

............2021,2022,2023,2026,2029,2049,2050,2096,2131

Radix ...........................................................................................2014

Randex .......................................................................................2014

Ricoh ..........................................................................................2128

Runco .........................................................................................2104

Samsung..............................2006,2013,2015,2033,2063,2112

Sanky ...............................................................................2131, 2104

Sansui ........................................................2010,2092,2111,2123

Sanyo ....................................................................2011, 2013, 2023

Sco_ •••2012,2015,2025,2032,2035,2038,2065,2093,2116

Sears ..............................................2011,2014,2021,2023,2048,

Funai ...............................................................................2002,2026 ...................................2049,2050,2051,2056,2056,2107,2118

Garrard .....................................................................................2026

GE ..................2000,2001,2013,2021,2022,2053,2116,2120

Goldstar ........................................2009,2014,2018,2054,2121

Gradiente .................................................................................2026

Harley Davidson .....................................................................2026

Harman Kmdon ......................................................................2009

Harwood ..................................................................................2061

Headquarter ............................................................................2011

Hitachi ...........2002,2055,2056,2057,2107,2111,2120,2122

HI-Q ..........................................................................................2023

Instant Replay ..........................................................................2021

ICE .............................................................................................2021

]C Penney ..........................2009,2010,2011,2013,2014,2021,

......................2022,2055,2056,2058,2059,2060,2107,2118

Jensen..................................................................2056,2056,2111

]VC ............................2009,2010,2011,2018,2058,2111,2123

Kenwood ,... 2009,2010,2011,2016,2018,2068,2111,2123

KLH ...........................................................................................2061

Kodak .............................................................................2014,2021

Lloyd ...............................................................................2002,2026

Logik ..........................................................................................2061

LX( .............................................................................................2014

Magnavox .................2021,2022,2062,2063,2104,2106,2124

Magnin .......................................................................................2013

Marantz ..............................................................2009,2010,2011,

..............................................2016,2018,2021,2058,2062,2064

Marta .........................................................................................2014

Masushita ..................................................................................2021

MEI .............................................................................................2021

Memorex ...........................................................2002,2011,2013,

............................................2014,2021,2023,2026,2104,2131

MGA ....................................................................2029,2066,2113

MGNTechnology ....................................................................2013

Midland .....................................................................................2053

Minolta ................................................................2056,2056,2107

Mitsubishi ...............2029,2065,2066,2065,2066,2067,2069,

......................2070,2071,2072,2073,2074,2106,2113,2123

MontgomeryWard ......................................................2075,2131

Sharp ........................2002,2017,2029,2094, 2096,2096,2131

Shintom .....................................................2004,2056,2061,2098

Shogun .......................................................................................2013

Signature .......................................................................2002, 2131

Singer ....................................................................2021,2061,2128

Sony .....................................2002,2004,2098,2099,2119,2128

STS ...................................................................................2021,2107

Sylvania ..........2002, 2021, 2022,2026, 2062, 2063, 2065, 2124

Symphonic ......................................................................2002,2026

Tandy ...............................................................................2002,2011

Tashiko .......................................................................................2014

Tatung ..............................................................................2058,2111

TEAC ..............................................2002,2026,2068,2085,2111

Technics ..........................................................................2021,2109

Teknika ................................2002,2014,2021,2026,2100,2129

TMK ......................................................................2013,2024,2047

Toshiba .....................2015, 2049,2051, 2055, 2066, 2093, 2116

ToteVision ......................................................................2013, 2014

Unitech ......................................................................................2013

Vector Research .....................................2009, 2010, 2015, 2016

Victor .........................................................................................2010

Video Concepts ...........................2009,2010,2016,2016,2113

Videosonic ................................................................................2013

Wards .......... 2002,2013,2014,2015,2021,2023,2026,2029,

.2056,2066,2061,2096,2101,2102,2103,2107,2116,2131

XR-IO00 ..............................................................2021,2026,2061

Yamaha ................................2009,2010,2011,2018,2068,2111

Zenith .............................................2004,2098,2104,2119,2128

Ir.,Y_Ift_l

ABC ..........................5002, 5003,5004, 5005, 6006, 5007, 5053

Antronix .........................................................................6008, 6009

Archer .......................................................5008,5009,5010,5011

Cabletenna ................................................................................6008

Cableview ..................................................................................5008

Century .....................................................................................5011

Citizen .......................................................................................5011

Colour Voice .................................................................5012, 5013

Comtronics ...................................................................6014, 5015

Contec ......................................................................................5016

]asco ..........................................................................................5011

Jerrold ...........5003,5005,5007,5018,6023,5024,5046,5063

Magnavox ..................................................................................5025

Memorex ..................................................................................5026

MovieTime ........................................................5002,5027,5028

NSC .....................................................................5002,5027,5028

Oak .......................................................................6002,6016,5029

Panasonic.......................................................................6048,6052

Paragon .....................................................................................5026

Philips ............5011,5012,5013,6019,6026,5030,5031,5032

Pioneer ...........................................................................6033,5034

Pulsar.........................................................................................5026

RCA .....................................................................5047, 5049, 5052

Realistic ..........................................................................6009, 5048

Regal ...............................................................................6022,5035

Regency ....................................................................................5017

Rembrandt ...............................................................................5003

Runco ........................................................................................5026

5amsung .........................................................................6014,6034

5cientificAt]anta .....................................5006,5036,5037,5038

Signal...............................................................................6014,5018

Signature ...................................................................................5003

5L Marx .....................................................................................5014

Sprucer .....................................................................................5052

5tarcom ...............................................................5007,5018,5053

5targate ..........................................................................6014,5018

Starquest ...................................................................................5018

Tandy .........................................................................................5046

Teleview ....................................................................................5014

]ocom .................................................................5004,5023,5041

]oshJba ......................................................................................5026

]_sa ............................................................................................5018

TV86 ..........................................................................................5027

Unika ...................................................................5008,5009,5011

United Artists ..........................................................................5002

United Cab]e ...........................................................................5053

Universal ..................................................5008,5009,5010,5011

Videoway ..................................................................................5044

Viewstar ...................................................5016,5025,5027,5040

Zenith ..................................................................5026,5050,5051

Chapparal ......................................................................6056, 5057

Drake .............................................................................6068, 5059

GE ...................................................................................6000, 5001

General Instruments ........................................5060, 5061, 5062

Panasonic..................................................................................5076

Primestar ..................................................................................5076

PROSCAN ....................................................................6000, 5001

RCA ................................................................................6000, 6001

Realistic .....................................................................................5063

Sony ...........................................................................................5072

STS1...........................................................................................5064

STS2...........................................................................................5065

STS3...........................................................................................5066

STS4...........................................................................................5067

loshJba ......................................................................................5068

Toshiba ......................................................................................5073

Uniden .......................................................................................5069

(_r RCA and Dimensia brands one)

AM/FM ......................................................................................4003

Aux ............................................................................................4004

Phono ........................................................................................4006

CD .............................................................................................4007

Tape ...........................................................................................4006

RCA, GE,PROSCAN ............................................................2001

Page is loading ...

RCA J32530YX58CJ6 User manual

Brand: RCA

Model: J32530YX58CJ6

Type: User manual

This manual is also suitable for

Download PDF

report

RCA J32530YX58CJ6 User manual

This manual is also suitable for

RCA J32530YX58CJ6 User manual

Related papers

Other documents