Lorex CVC2532 Installation guide

Category
Security camera accessories
Type
Installation guide

Lorex CVC2532 is an indoor color dome camera with a polycarbonate housing that provides high impact protection against possible vandalism. Its smoked camera housing provides an unobtrusive appearance. The 1/4” CCD Color image sensor with a polycarbonate dome housing allows you to rotate the camera 360° and/or tilt it 90° for optimal angle selection. Built-in automatic back light compensation ensures optimal image quality in various lighting conditions.

Lorex CVC2532 is an indoor color dome camera with a polycarbonate housing that provides high impact protection against possible vandalism. Its smoked camera housing provides an unobtrusive appearance. The 1/4” CCD Color image sensor with a polycarbonate dome housing allows you to rotate the camera 360° and/or tilt it 90° for optimal angle selection. Built-in automatic back light compensation ensures optimal image quality in various lighting conditions.

CVC2532 INDOOR COLOR DOME CAMERA
Overview
Polycarbonate housing provides high impact
protection against possible vandalism
Smoked camera housing provides
unobtrusive appearance
• 1/4” CCD Color image sensor with
polycarbonate dome housing
Rotate camera 360 and/or Tilt camera 90
for optimal angle selection
• Built-in automatic back light compensation
Package Contents:
§ Check the package for the following contents
listed below.
Installation Instructions:
1. Open the dome by unscrewing the ring
counterclockwise
2. There are two mounting holes located on
the dome base. Use this to install the
dome on a wall, ceiling, etc
3. Apply power to the camera (using supplied
12V DC Adapter).
4. Connect the video cable to the BNC
connector (provided) if connecting to a
TV/Monitor or DVR with a BNC input.
5. Adjust the pan/tilt direction of the camera
for the desired picture view.
6. Close the dome by turning the ring
clockwise.
Note: If you are using the RCA video cable to
connect the camera to a TV you must tune your
television to an auxiliary (AUX), A/V or video
mode to view the camera (Note: Consult the TV’s
Owner’s Manual for setting the TV to an auxiliary,
A/V or video mode.)
CVC2532 INDOOR COLOR DOME CAMERA
Specifications
As our products are subject to continuous improvement,
SVII and its subsidiaries reserve the right to modify product
design, specifications and prices, without notice and without
incurring any obligation. E&OE
Image Sensor
1/4" Interline transfer type Col
CCD
Effective
Pixels 510H x 492V (250K)
Scanning
System
525 Lines 2:1 Interlace
Scanning
Frequency 15.734KHz (H), 59.94Hz (V)
Resolution
330 TV-Lines
Shutter Speed
1/60 ~ 1/100,000 sec.
S/N Ratio
More than 48dB (AGC off)
Sync. System
Internal
Min.
Illumination <1 LUX (F2.0)
White Balance
AWB
Video Output
1.0 Vp-p (75? load)
Lens
Fixed (3.6mm)
Power Supply
DC12V ± 10%
Power
Consumption
100mA (DC12V)
Operating
Temp
-10 to +45 C / 14 to 113F
Operating
Humidity 90% RH Max.
Diameter
125mm
Camera &
Bracket
Manual
Power
Supply
CVC2532
INDOOR COLOR DOME
CAMERA
Distributed By:
STRATEGIC VISTA
300 Alden Road, Markham,
Ontario Canada L3R 4C1
For more information, visit:
www.strategicvista.com
  • Page 1 1
  • Page 2 2

Lorex CVC2532 Installation guide

Category
Security camera accessories
Type
Installation guide

Lorex CVC2532 is an indoor color dome camera with a polycarbonate housing that provides high impact protection against possible vandalism. Its smoked camera housing provides an unobtrusive appearance. The 1/4” CCD Color image sensor with a polycarbonate dome housing allows you to rotate the camera 360° and/or tilt it 90° for optimal angle selection. Built-in automatic back light compensation ensures optimal image quality in various lighting conditions.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI