X-cam Sight 2 User manual

Brand: X-cam

Model: Sight 2

Type: User manual

Mini-USB

Instructions Manual

LED Indicator

Phone compatibility

Pitch axis angle range

Horizontal shaft angle

Pitch axis control angle

Bluetooth

Battery

Charging time

Maximum power

Working duration

Material

Size

Weight

Smart phone with screen size less than 5.5”

± 175 degrees

± 55 degrees

± 45 degrees

1,000 mAh Li-Po

2-3 hours

<= 10w

2-5 hours constantly (depending on phone weight)

PC engineering plastic

150(L) x 48(W) x 54(MH)

189g

Need to charge when red LED slowly flashes

Ready for auto turn off when red LED rapidly flashes

Bluetooth connection is available when blue light

dimly flashes (Bluetooth version only)

Works normally when blue LED lights up constantly

1.PRODUCT PARAMETERS

Low consumption International Bluetooth 4.0 standard

2.PACKAGING COMPONENTS

Handheld gimbal

Charging cord Hex allen wrench Velvet bag

Instructions manual

Certificate of quality

EVA thickening pads

(only needed for small-sized smart phone)

Certificate of quality

3.STRUCTURES OF HANDHELD GIMBAL

Green LED light is on when charging.

LED light is off when charging has completed.

Power switch

(press and hold for two

seconds to turn on/off)

LED indicator

(5V Power Adaptor)

Charging port

TILT knob

(Center is photo

/video button

- Bluetooth

version only

ATTENTION

This gimbals is motor-lock protective. When

bumped or obstructed, the gimbals will

automatically shut off in 10-15 seconds.

The packaging and user manual contain important

information and should be kept for future reference.

Safety Instructions

1)Keep the device away from flammable materials and heat sources

when charging. Do not cover either the device or the charger.

Make sure to charge under safe and ventilated circumstances.

2)Never leave the charging process unattended.

3)Keep the device away from water, oil and other corrosive liquids

or gases to avoid short circuit that might damage the electronic

system or lead to battery explosion.

4)Charge the device regularly when not in use for long periods of

time.

5)Turn off the device and stop charging immediately when there is

a burning smell, deformation or other abnormal cases occur. Be

sure to handle the device properly.

Instructions for disposal of WEEE by users in the European

Union

This product must not be disposed of with other wastes. Instead, it

is the user’s responsibility to dispose of their waste equipment by

handing it over to a designated point of collection for the recycling

of waste electrical and electronic equipment. The separate

collection and recycling of your waste equipment at the time of

disposal will help to conserve natural resources and ensure that it is

recycled in a manner that protects human health and the

environment. For more information about where you can drop off

your waste equipment for recycling, please contact your local city

office, your household waste disposal service or where you

purchased the product.

Disclaimer

Misoperation of charging might lead to fire and personal injury or

property damage. User of this device agrees to acknowledge all

risks in using the device.

Other device:

This device complies with part 15 of the FCC Rules. Operation is

subject tothe following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

ATTENTION

2axis stabilizing system

Bluetooth connection

Foldable structure

RoHS

Warning

“Shanghai RUIPAI Intelligent technology Co.Ltd.", the

manufacturers, wholesalers and dealers do not bear any legal

responsibility for any accidents the user might incur that was not

caused by the quality of the product. Please read the instruction,

especially the caring part carefully. If you are unsure how to charge

the device, please consult your local dealer

before use.

Class B device:

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for

help.

Any changes or modifications to this unit not expressly approved

by the party responsible for compliance could void the user's

authority to operate the equipment.

90°

Take out the X-CAM sight 2 from the gift box, put

your smart phone into the phone holder. Do not turn on

the gimbal before the your phone has been mounted

balanced on the gimbal. If power button of your phone

is on the side of your phone, make sure not to press it

when you mount the phone to the phone holder.

Now adjust gravity of the roller. The phone is

tilted to the left in the above photo, you need

to push the phone to the right.

The phone is tilted to the right in the above

photo. To adjust gravity of the roller you need

to push the phone to the left.

Shake the X-CAM sight2 lightly, if your phone

remains balanced, congratulations that

adjustment of gravity of the roll is completed.

Fold the machine arm 90 degrees

perpendicular to the body, until the hexagon

screw hole reaches against the silver metal

part .

Hold X-CAM sight2 with your right hand.

Rotate the machine arm until screen of your

phone faces you. Now check gravity of the tilt.

Shake X-CAM sight 2 lightly. If the phone remains

balanced vertically, gravity of the tilt is OK, so no further

adjustment to gravity of the tilt needed. You can use

your X-CAM sight 2 now. Gravity of the tilt is fixed once

and for all.

If phone screen faces down as shown in above photo,

you need to adjust gravity of the tilt. Turn the hex allen

wrench counterclockwise as shown on Photo 10. Fold up

the roller arm to check tilt gravity again.

If phone screen faces up as shown in above photo, you

need to adjust gravity of the tilt. Turn the hex allen

wrench clockwise as shown on Photo 10. Fold up the

roller arm to check tilt gravity again.

Use the hex allen wrench packed in the

package to adjust protrusion of the nut.

Range of adjustment is within 360 degree

clockwise or counterclockwise.

Press the power switch for 2 seconds to turn on your

X-CAM sight 2. Congratulations! You could now use your

X-CAM sight2. If your sight 2 is Bluetooth version, please

refer to "Paring Bluetooth" on next page to connect your

phone to X-CAM sight 2.

Turn the tilt knob to control the tilt angel of

your phone. Press center of tilt knob to take

photos and videos (Only available for

Bluetooth version)

It is very important to install your phone balanced

on the gimbal. Unbalanced gravity of the phone will

lead to auto-power-off of the gimbal. Please scan

the QR code on the right for a quick guidelines on

how to install your phone and adjust gravity.

6. BLUETOOTH PARING:

Starting up1) - Please activate Bluetooth in your phone after you

have installed your phone balanced on X-CAM SIGHT 2.

2) - Press power button 2 seconds to turn on X-CAM Power on

SIGHT2. Blue light beside the power button flashes dimly,

indicating the gimbal is searching for Bluetooth devices.

3) -Normally, it takes the phone 3 seconds to search forSearch

available Bluetooth devices. Now you will find 'X-CAM SIGHT2'

in devices list. (For 1st time connection, it might read as EFF...)

4) -Select 'X-CAM SIGHT2' and follow the onscreen promptsPAIR

to pair your phone with X-CAM SIGHT 2. Blue LED on the

gimbal lights up constantly if your phone is successfully

connected with X-CAM SIGHT 2.

ATTENTION

X-CAM SIGHT2

Bluetooth Pairing Request

"X-CAM SIGHT2"would

like to pairwith your iphone.

Cancel Pair

X-CAM SIGHT2

1.Gravity of the phone is not

balanced on the tilt or roll

direction. Poor balance leads to

too large current and triggers

overload protection.

2.There is obstruction to the gimbal,

maybe from your phone or collision

while you are shooting. Obstruction

leads to excess resistance and

triggers overload protection.

3.You turn on the gimbal without

phone installed.

4.The handle of the gimbal (the

panel with silver printing logo) is

placed horizontally.

1.Adjust gravity of your phone on

the gimbal before turn on the

gimbal. Make sure your phone

does not tilt to the left or the right,

leans to the front or the back.

2.Properly install your phone to the

gimbal, make sure the phone will

not touch any part of the gimbal

except the phone clipper when

you use it. Do not bump into any

obstruction when you use the

gimbal.

3.You should properly install your

phone on the gimbal before turn

on the gimbal. Otherwise, the

gimbal will activate overload

protection and automatically

shut off.

4.Never place the handle of the

gimbal (the panel with printed

logo) horizontally, or the gimbal

will activate overload protection

and automatically shut off.

1.Power of your gimbal is full.

2.Something is wrong with your

USB charging cable.

1.Your gimbal is non Bluetooth

version, which does not have

Bluetooth function.

2.Your phone has been connected

to other device.

3.Bluetooth version of your phone

is too low.

1.Please buy gimbal equipped

with Bluetooth.

2.Disconnect your phone to

other device first and pair it

with X-CAM SIGHT 2.

3.Make sure Bluetooth version

of your phone is 4.0 or up and

Android version of your phone

is 4.3 or up.

1.Power of your gimbal is full. If

you are still unable to turn on the

gimbal, the reason must be that

gravity of your phone on the

gimbal is still not balanced.

2.Charging cable of the gimbal is

the same with most of the Android

phones. Please compare if the

plugging end is the same, you

could use your Android phone's

charging cable.

I'm

unable

charge

the

gimbal.

phone

can not

pair with

the

gimbal.

4. TROUBLE SHOOTING

Problem

Cause

Solution

The

gimbal

is auto

power

off.

5. QUICK START:

X-cam Sight 2 User manual

Brand: X-cam

Model: Sight 2

Type: User manual

Download PDF

report

X-cam Sight 2 User manual

X-cam Sight 2 User manual

Other documents