LG UB2GVMS01P User manual

2

Before Using USB Drive

-----------------------------------------------------------------------------------------------------------

3

What is USB Drive?

-------------------------------------------------------------------------------------------------------------------

4

Installing/Using USB Drive

in Microsoft Windows ME/2000/XP

--------------------------

6

Installing/Using USB Drive in Microsoft Windows 98/98SE

--------------------------------

10

Installing/Using in MacOS ( MacOS 9.0 or later )

-----------------------------------------------------

12

Using the LG USB Drive Utility

------------------------------------------------------------------------------------------

13

USB Drive FAQs

--------------------------------------------------------------------------------------------------------------------------

23

Contents

3

Welcome to USB Drive.

This user guide is designed to help you use USB Drive correctly and safely. Please read this

information carefully before using USB Drive. Please pay special attention to the sections that

describe USB Drive operation for the Operating System being used by your computer.

Safety Instructions

These Safety Instructions include directions and precautions for you to follow when using USB

Drive. The instructions aim to secure your safety and to prevent any damage to your computer,

your USB Drive and your data.

Warning instructions indicate that failure to follow the directions could result in possible personal

injuries.

Caution instructions indicate that failure to follow the directions could result in damage to the USB

Drive or data.

Warning

- To reduce the possibility of electrical shock, do not use the USB Drive if wet with any liquids

such as water or chemicals.

- To reduce the possibility of an electrical short circuit, do not plug the USB Drive into your

computer’s USB port. Plugging a wet USB Drive in causes a danger of damaging the USB

Drive and/or your computer.

- If any smoke or strange smells or noise occurs when using USB Drive.

Be sure to turn off your computer and peripheral devices immediately and disconnect the power

cords.

Before Using USB Drive

4

Caution

- Do not disconnect the USB Drive from the computer’s USB port while transferring (reading or

writing) data. This will probably result in your data being corrupted

- Make sure that you follow the instructions given in this guide when using or removing the

product. Incorrect use of USB Drive may cause a malfunction of the product and/or loss of your

data.

- Be careful not to bend or twist the USB Drive. Do not place any heavy object on the product.

- Please do not attempt to disassemble or modify the product.

It can cause malfunction of the product. There are no user serviceable parts in the USB Drive.

- Do not use your USB Drive in any place exposed to the following conditions, as it may cause a

malfunction of the product : excessive vibration or shock; wetness, moisture or dust; heat

and/or high temperature variation; strong electrical discharge; strong magnetic interference.

- Be careful that any foreign material does not enter the insertion holes of USB Drive

LG Electronics Inc. assumes no responsibility for any corruption or loss of data and

accompanying results due to incorrect use of the product.

USB Drive is a removable, portable, flash memory based data storage device that works via your

computer’s Universal Serial Bus (USB) interface. USB Drive does not require a battery or any

external power because the USB Drive uses the power supplied by the computer or USB device it

is plugged into. USB Drive works with your computer’s plug-and-play system,

for most operating

systems, once it is plugged into the USB port of your computer.

It is ideal for mobile professionals, or

for anyone with a need to move data frequently and conveniently between devices or networks,

since it is very small and lightweight. Through Utility, you can make USB Drive security-enabled,

partition –enabled, bootable disk-enabled. The Security feature is currently compatible with

Microsoft Windows XP, 2000, ME, 98 and 98SE.

What is USB Drive?

5

Formatting USB Drive

USB Drive has already been formatted and initialized with the FAT file system before delivery and

is ready for immediate use.

Operating System Requirements

Operating Systems Driver Installation

1. Microsoft Windows Vista

2. Microsoft Windows ME/2000/XP

3. Mac OS 9.0 or later

4. Linux 2.4.0 or later

None required

1. Microsoft Windows 98/98SE Required

¾ When using Microsoft Windows ME/2000/XP/Vista, MAC 9.0 or later, Linux 2.4.0 or later, USB

Drive can be installed and removed without powering down your computer. When using

Microsoft Windows 98/98SE, you must install additional drivers before you can use the USB

Drive

¾ The additional Windows 98/98SE drivers can be downloaded from the www.lge.com

homepage.

¾ For Linux, it is required to mount SCSI.

Note:

6

1. Start Windows ME, Windows 2000 or Windows XP.

2. Remove the cover from your USB Drive and plug it into a USB port on your computer.

If it is the first time to use USB Drive, Windows will automatically recognize it and install all

required drivers.

3. The red Status LED will flash during the recognition and installation procedures. When

USB Drive

is ready to use, the Status LED will turn off.

4. Click My Computer on Windows Desktop. USB Drive is displayed as a removable disk, as is

shown in the following figure.

(The drive name may be different depending on the system you are using).

5. You can now read or write data using the installed USB Drive, the same as with any other hard

drive.

Removing USB Drive in Microsoft Windows ME/2000/XP

1. Close all files currently opened from USB Drive.

2. Click Safely Remove Hardware Icon on the Task Bar or the System Tray as shown in the

following figure.

Installin

g

/Usin

g

USB Drive in Microsoft Windows ME/2000/XP/Vista

7

3. Select to remove hardware.

4. When your computer indicates it is acceptable to remove hardware, then unplug the USB Drive

from the USB port.

Basic Information★

The USB Drive may be partitioned into three types of disk. We will use the following terms in this

guide:

1. Public Area There is no “Security” function at all. You can do any basic functions,

described in the “Basic Functions” section, in this area.

2. Security Area This area cannot be viewed without the application software. Once you do

the “Log In” action in the application software, you will switch view from

“Public Area” to “Security Area”. After successful switch, you can do any

basic functions, described in the “Basic Functions” section, in this area.

☞ You can only view either “Public Area” or “Security Area” at the same time

in the same disk logic unit number(LUN).

In USB Drive, you can select the following partition combinations:

1. Single Public Area: Make all the device area accessible by everybody.

2. Security Area:

Make the device area into two partitions in the same LUN, Public Area and Security Area.

Everybody can access the Public Area. The Security Area can be accessed “Only” with a

password.

3. Public Area Plus Security Area:

Make the device area into three partitions in two LUNs, Public Area and Security Area in LUN0

and Public Area in LUN1.

Partition Type

Caution: Never remove or unplug USB Drive while the Red Status LED is flashing. Doing this may

cause corruption of the data being transferred.

8

You can access these partitions by the multiple-LUN driver. The partition status was shown in the

following figure. The partitions in LUN 0 will perform as described in item 2. The partition in LUN 1

will perform as described in item1.

The figure shows detailed operations of single LUN.

This figure shows detailed operations of multiple LUNs.

Public

Area

Security

Area

Change View

Through

Login & Logout

LUN 0

Security

Area

Security

Area

Public

Area

Change View

Through

Login & Logout

LUN 0

LUN 1

9

Function Type Security Password

Disk Logical

Unit Number

Disk Letters

in OS

1. Public Area Only No No 1 (LUN0) 1

2. Security Area Yes Yes 1 (LUN0) 1

3. Public Area Plus Security Area Yes Yes 2 (LUN0 & LUN1) 2

This table describes the functions of the three partition type.

Using the Software

Installing/Uninstalling the Application Software:

Installing the software:

If you are installing the application software onto Windows OS, you must first log on as the

administrator and then install the application software.

Precaution about the USB Interface

¾ Please connect the device to the USB port of your computer when you install the

application software.

¾ If you do not connect the device to the USB port and install the application software in

the Microsoft Windows 2000, XP, you have to install the USB Drive driver again as you

plug in the device.

¾ In Windows 98 SE and Win ME, you need to unplug the USB Drive and plug again after

install the driver.

1. Find the “Utility” program.

2. Double-click the program icon.

3. Follow the on-screen instructions to proceed.

On the Windows Platform

10

Uninstalling the software:

To remove the installed software, you can click the windows [Start] menu and select [Setting],

[Control Panel] and [Add/Remove Programs]. The application software can also be uninstalled by

clicking the [Start] menu and selecting [Programs], [LG USB Drive], [Uninstall LG USB Drive].

¾ The USB driver will be required to install, as the device links the PC by the USB port at the fist

connection. After then, the drive installation is not required.

¾ Do not cancel the installation during the procedure. The LG USB Drive may not operate

correctly if the installation is incomplete.

¾ Read the “Troubleshooting” Section if the installation cancels itself during the procedure, if the

installation did not proceed as described, or if you feel that the driver are not properly installed.

Installing the USB Drive:

For some Windows system, users should log on as the Administrator before installation. Once you

have attached the USB Drive to the computer. The OS will find the appropriate driver or the “Add

New Hardware Wizard” dialog will appear after a moment. You can do the installation of the Driver

manually. Or just find out the “LG USB Drive.exe” program to do the driver installation.

During the installation procedure, if the “Digital Signature Not Found” message displays, just click

the [Yes] button in the showing window.

For Microsoft Windows 98/98SE, you can download it from http://www.lge.com/

.

Installin

g

/Usin

g

LG USB Drive in Microsoft Windows 98/98SE

Note:

11

Installing LG USB Driver

1. Start Windows 98 or Windows 98SE.

2. Click Windows 98/98SE Driver Installation

3.

When driver is successfully installed.

4.

Remove the cover from your USB Drive and plug it into an USB port of your computer.

5. After taking off the cap of the USB Drive and Insert it to USB port of your PC, then it is

recognized by the PC as a Removable Disk automatically.

※ For some Windows system, users should log on as the Administrator before installation.

Once you have attached the USB Drive to the computer. The OS will find the appropriate driver

or the “Add New Hardware Wizard” dialog will appear after a moment. You can do the

installation of the Driver manually. Or just find out the “LG USB Drive Win98Driver Setup.exe”

program to do the driver installation.

During the installation procedure, if the “Digital Signature Not Found” message displays, just click

the [Yes] button in the showing window.

Removing USB Drive in Microsoft Windows 98/98SE

1. Close all files currently opened from USB Drive.

2. Unplug USB Drive from the USB port.

Caution: Never remove or unplug USB Drive while the Red Status LED is flashing.

12

1. Start MacOS.

2. Remove the cover from your USB Drive and plug it into an USB port of your MAC. If it is the first

time to use USB Drive. MAC will automatically recognize it.

3. USB Drive is recognized as an [untitled] folder in MAC.

4. You can read or write data using USB Drive, just the same as with any other hard disk drive.

Removing USB Drive

1. Close all files currently opened from USB Drive.

2. Drag and drop the [untitled] folder to the Recycle Bin.

3. Unplug USB Drive from the USB port.

Caution: Never remove or unplug USB Drive while the Red Status LED is flashing.

Installin

g

/Usin

g

USB Drive in MacOS

(

MacOS 9.0 or later

)

13

Through LG USB Drive Utility, you can make USB Drive security-enable. Security feature is

currently compatible with only Windows XP/2000/ME/98SE/98.

1. Plug USB Drive directly into your computer’s USB port.

2. After your USB Drive is recognized, Double-click the program icon.

3. A pop-up menu will be displayed.

4. Click on the menu item named

[Using LG USB Drive.exe Program the First Time]

Warning: Due to the LG USB Drive.exe can only handle one USB Drive

device at the same time. If you will not use the function of the LG USB

Drive.exe, like “Resize”, “Change Password”, or “Log In”, etc., you can insert

more than two USB Drive devices. If you want to use the function of the

program, remove all other USB Drive device. Otherwise, the USB Drive.exe

may not perform properly or even cause data loss.

After you install the software and driver correctly, the USB Drive icon will appear at the notification

area automatically.

Or

The display will depend on the status of the device.

Using the LG USB Drive Utility

14

¾ You can use the right button of your mouse to pop up the selection menus as the following

figures. Then, you can select the functions you want.

¾ Or you can double click the icon in the notification window. The USB Drive manager window

will pop up as,

By default, the device is non-security. So, the “Resize” function will be active when you run this

software first time.

[USB Drive – Resize]

As described in the “Partition Type” section, you can do the “Resize” action to your USB Drive.

15

Warning: The “Resize” action will erase all the data or files existing in USB

Drive. The action is not reversible. You have to backup all the important files or

data. Also, please close all the active programs and windows on the screen of

your computer.

1. Click the Resize button in the USB Drive manager window. The following “Resize Partition”

windows pop up.

2. Select the partition type you want.

3. If you select the “Public Area Only”, then click the [OK] button. The “Confirmation” window will

pop up. Please make sure you already backup all the important files or data.

16

4. If you select the “Security Area”, then the following “Security Area Resize” window will pop up.

You can drag the scroll bar in the middle of the window to set the size of the “Public Area” and

“Security Area”. Or you can type in the size of each Zone you want in the “Size” window. You can

set the password for accessing the security area in the “New Password” window. The maximum

size of the password is 8 characters. You can key in the hint of your new password in the

“Password Hint” window. This hint will be displayed when you click the “Hint” button in the “Unlock

Protect” window. The maximum size of the Hint is 32 characters. After you finished the setting,

click the [OK] button. The “Confirmation” window will pop up. Please make sure you already

backup all the important files or data.

5. If you select the “Public Area + Security Area”, then the following “Public/Security Area Resize”

window will pop up. You can drag the scroll bar in the window to set the size of each area. First,

please set the size of the “Public Area” of LUN1. The minimum size for each area is 1MB. The

maximum size of the “Public Area” of LUN1 is 1/4 of the total size. Once the size of the “Public

Area” of LUN1 was set, the scroll bar of the “Public Area” and “Security Data Zone” of LUN0 will

be set in the middle automatically. Or you can type in the size of each Zone you want in the “Size”

window.

17

You can set the password for accessing the security area in the “New Password” window. The

maximum size of the password is 8 characters. You can key in the hint of your new password in

the “Password Hint” window. This hint will be displayed when you click the “Hint” button in the

“Unlock Protect” window. The maximum size of the Hint is 32 characters. After you finish the

setting, click the [OK] button. The “Confirmation” window will pop up. Please make sure you

already backup all the important files or data.

6. Once the resizing is finished, the following message will pop up.

18

7. After you finish the “Resize”, the “Setup.exe” program will be copied into the “Public Area” (in

LUN 0) automatically. It’s removable. However, it is needed when you insert your device into

another computer. It will install the USB Drive software for you in the computer.

[Login the Security Area]

If you partition the device with security, you can execute the following “Login” function to access the

security Area.

1. Double click the USB Drive icon in the notification window or click the [Login] button in the USB

Drive manager window. The “Unlock Protect” window will pop up.

Warning: When you do the login and logout action with the device please

make sure there is no application or program running or document unclosed on

the device. If so, it will cause data loss or damage.

19

2. Key in the password in the “Password” area.

¾ You can create the password hint in the “Resize” or “Change Password” functions. Once

you create the password hint, you can click on the “Hint” button in the “Unlock Protect”

window to prevent you from forgetting the password. The hint will be shown for three

seconds.

¾ If you key in the wrong password, the following message will be shown.

¾ You have three tries to input the password. After three tries, the following message will pop

up. And you have to unplug and plug the device in order to do future actions.

20

When you do the login or logout action, please make sure you close all the programs or

documents open connection on the device. If there is some application programs running or

documents unclosed on the device, the following message will pop up. In Win2000, even

the “file manager” has accessed the device it will be treated as “busy”. You have to close

the file manager in order to do the “Login”. However, not all the connection could be

checked in all kind of OS.

3. Click on the “OK” button.

4. Once the file manager window contains the “Security Area” pops up, you can do the operation

you want with the Security Area. The file manager window will be like the following figure. The

background is colorful.

Page is loading ...

LG UB2GVMS01P User manual

LG UB2GVMS01P User manual

Related papers

Other documents