Polycom EF2241 User manual

Vortex EF2241

Reference Manual

VORTEX EF2241 REFERENCE MANUAL

Introduction....................................................................................................2

Product Features .................................................................................................... 3

Pre-Installation...............................................................................................5

EF2241 Front and Rear Panels.............................................................................. 6

Installation .....................................................................................................8

Mounting the EF2241 ............................................................................................. 8

Connecting the EF2241 to Other Equipment ......................................................... 8

Device IDs on the EF Bus....................................................................................... 10

Connecting Multiple Vortex Devices ...................................................................... 10

Factory Default Settings (Preset 0) ........................................................................ 11

Check Surrounding Equipment............................................................................... 13

Integrating the EF2241 Into Your System.....................................................15

Input Settings .......................................................................................................... 15

Calibration.............................................................................................................. 15

Set up the Phone Interface...................................................................................... 17

Build Your Echo Canceller Reference.................................................................... 17

Echo Canceller Reference for Multiple Vortex Devices......................................... 17

Configure the Automatic Microphone Mixer.......................................................... 19

Automixer Settings for Multiple Vortex Devices .................................................... 21

Configure the Matrix Mixer.................................................................................... 22

Building Your System with Multiple Vortex Devices.............................................. 22

The EF Bus ....................................................................................................24

Presets..................................................................................................................... 25

Other EF2241 Features.......................................................................................... 25

LCD Menu Structure .....................................................................................26

System Menu ........................................................................................................... 28

Phone Control......................................................................................................... 29

Inputs ...................................................................................................................... 30

Outputs.................................................................................................................... 31

Automixer Menu...................................................................................................... 31

Matrix Menu ........................................................................................................... 34

Parametric EQ Menu.............................................................................................. 35

Presets..................................................................................................................... 36

Macros .................................................................................................................... 36

Troubleshooting .............................................................................................37

Automatic Microphone Mixer................................................................................. 37

Matrix Mixer........................................................................................................... 38

Echo Canceller Reference ...................................................................................... 38

Residual Echo ......................................................................................................... 38

Contacting Technical Support ................................................................................ 43

Technical Specifications ................................................................................44

Compliance............................................................................................................. 45

Conference System Design............................................................................49

EF2241 Block Diagram .................................................................................50

Connector Pinouts..........................................................................................51

Connecting Unbalanced RCA to Balanced Mini Phoenix...................................... 53

Making an EF Bus Terminator............................................................................... 53

Additional Notes ..................................................................................................... 54

Warranty Information ....................................................................................55

Definition of Terms .......................................................................................57

Index ..............................................................................................................60

INTRODUCTION

VORTEX EF2241 Reference Manual 2 Technical Support: 800.932.2774

I

NTRODUCTION

Welcome Congratulations on your purchase of the Vortex EF2241!

How to Use This

Manual

This is a reference manual for your EF2241. It is structured to provide the informa-

tion you need quickly and conveniently. The following is an overview of each sec-

tion:

• Introduction

• Pre-Installation includes information about the contents of the box, tools needed

for installation and front and rear panel descriptions.

• Installation covers connections of inputs/outputs and calibration of inputs of the

EF2241.

• Integrating the EF2241 Into Your System describes adjustments to take into con-

sideration when integrating the EF2241 with surrounding equipment in your sys-

tem.

•LCD Menu Structure describes an overview of the LCD menu structure and also

gives a system overview of features and options available.

• Troubleshooting helps to debug problems with installation.

• Technical Specifications provides the technical specifications of the EF2241.

• Conference System Design gives suggestions on topics to consider when design-

ing your system.

• EF2241 Block Diagram shows the inside of the EF2241.

• Connector Pinouts shows pinout diagrams for EF2241 input and output connec-

tors.

• Warranty Information

• Definition of Terms explains terms used in this manual, as well as terms used in

our technology of echo cancellation, noise cancellation, and audio conferencing.

About the EF2241 The Vortex EF2241 is a companion to the Vortex EF2280, or a stand-alone solution

for audio conferencing. It automatically mixes four microphones and other audio

while cancelling acoustic echoes and annoying background noise, and features a

built-in “phone add” to bring telephone calls into the conference. A total of 8 Vortex

devices can be linked together (for instance, 8 EF2280s, or 2 EF2241s and 6

EF2280s).

The EF2241 has 4 mic/line inputs, 4 line inputs and 8 line outputs with 4 channels of

acoustic echo and noise cancellation. It has matrix mixing and automatic microphone

mixing capabilities, a single telephone line interface, and a single channel power amp.

It includes a total of 8 analog inputs (4 mic/line level inputs and 4 line level inputs), 8

analog outputs, and 5 digital expansion busses (one being dedicated to phone).

Acoustic echo cancellation (AEC) and noise cancellation can be applied to each of the

4 mic/line level inputs, and each of these inputs can then be sent to one of the two

internal automatic microphone mixers.

The system also contains a 23 x 17 main matrix, four 7 x 3 submatrices, and one 7 x 2

submatrix for transporting audio from the phone line. The 23 x 17 main matrix has

the following inputs: Input channels 1-4 (gated or ungated), Input channels A-D, the

internal signal generator, 3 mixes of each of the four digital busses (3 mixes times 4

INTRODUCTION

busses equals 12 inputs), and 2 mixes of the P Bus for the telephone. The 23 x 17

main matrix has the following outputs: Outputs 1-4 and A-D, AEC Reference 1 and 2,

W, X, Y, and Z outputs to the digital expansion bus, P output to the digital expansion

bus, output to the power amplifier, and output to the phone line. The EF2241 has 24

bit resolution, 32-bit floating point computation, and a 48 kHz sampling rate.

Polycom’s proprietary noise cancellation on each of the 4 mic/line inputs and the tele-

phone line helps to keep overall ambient noise to a minimum. Polycom echo cancel-

lers are the only ones on the market to feature this patented technology. Noise

cancellation filters out ambient background noise such as noise from heating, venti-

lating and air conditioning (HVAC), LCD projectors, and road noise. Our noise can-

cellation technology is not a noise gate. It actually removes noise. Therefore, it

enhances the operation and improves the sound quality of an automixer, for example,

by preventing it from bringing the noise level up and down when microphones are

gated on and off. By cancelling the noise picked up by each microphone, the overall

signal to noise ratio (SNR) is preserved. The result is crystal clear speech over a

greater decibel range than any other echo canceller. That means reduced listener

fatigue and a higher quality audio conference.

Product

Registration

Please take a moment to fill out and return your registration card. This information

will help us to provide you with better customer support and will allow us to notify

you with updated product features and software.

P

RODUCT

F

EATURES

Product • Front panel LCD for controlling and configuring the product without a computer

• 5-band equalizer on all Inputs and Outputs

• Echo cancellation on Inputs 1-4

• Noise cancellation up to 15 dB

• Two internal automatic microphone mixers for Inputs 1-4

• 23 x 17 full cross point matrix mixer with expansion bus

• Internal signal generator for calibration mode and noise masking applications

• 2 year warranty

AEC • 24 bit resolution

• 48 kHz sampling rate, >20 kHz bandwidth

• 270 ms AEC tail length

• 40 dB/sec convergence rate

• Can function in rooms with more than 10 dB of room gain

LEC • 32 ms LEC tail length

• 40 dB/sec convergence rate

• > 65 dB total cancellation

INTRODUCTION

VORTEX EF2241 Reference Manual 4 Technical Support: 800.932.2774

Inputs and

Outputs

• 4 microphone/line level inputs with phantom power on each input

• 24 VDC Phantom Power

• 4 line level auxiliary inputs with nominal level of 0 dBu

• 8 line level outputs with default nominal level of 0 dBu

• Automatic Gain Control (AGC) on Inputs 1-4.

Remote Control • RS-232 port for remote control

• Reconfigurable parallel logic input/output

• EF bus for linking multiple Vortex devices

• Digital bus with 5 audio busses, 48 kHz sampling rate

• Up to 8 Vortex devices can be linked, each device providing 4 audio signals on

the bus and each EF2241 providing 1 phone audio signal on the bus

PRE-INSTALLATION

P

RE

-I

NSTALLATION

What’s Included The Vortex EF2241 product package includes the following items:

• Vortex EF2241 Reference Manual

• Vortex EF2241

• External power supply

• Cat 5 cable for EF Bus

• Telephone cable

• Rack mount screws (4)

• Phoenix connectors (16)

• Cable clamp and screw

• CDROM containing other manuals and Conference Composer software

• Product Registration Card

What’s Not

Included

The following equipment is not included with the EF2241 product package, but may

be necessary to create a completely functional system:

• Microphones

• Loudspeakers

• Audio cables

• Videoconferencing codec or other four-wire interface (optional)

• RS-232 remote control device (optional)

Tools Needed for

Installation

• Screwdriver to mount the EF2241 in your rack.

• Phoenix connector screwdriver

Figure 1. What’s Included with your Vortex EF2241.

x

Vortex

®

EF2241

Rackmount

Screws (4)

Cable Clamp

and screw

CDROM with

control software and manuals

External

Power Supply

Vortex EF2241 Reference Manual

Vortex

®

EF2241

Reference Manual

Phoenix

Connectors (16)

1-Cat 5 cable

for EF

Bus

1-Telephone cable

PRE-INSTALLATION

VORTEX EF2241 Reference Manual 6 Technical Support: 800.932.2774

EF2241 F

RONT

AND

R

EAR

P

ANELS

1. LCD DISPLAY. Displays menu instructions for configuration and operation of the

EF2241.

2. D

OWN BUTTON. Scrolls backward through menu items at a particular level or

decreases the value of a parameter.

3. U

P BUTTON. Scrolls forward through menu items at a particular level or increases

the value of a parameter.

4. E

NTER. Enters the menu and allows you to select and change parameter values.

5. E

SC. Returns to the next highest level of menus.

6. H

OME. Returns to the top of the menu structure.

7. L

EVEL INDICATOR. Indicates the level of the selected channel or parameter.

8. P

HONE CONNECT. Takes the phone line on or off hook. If you have an analog

handset connected to the P

HONE jack on the back panel, pushing this button will

disable the P

HONE jack while enabling the LINE jack (see Item 17).

9. C

HANNEL ACTIVITY LEDS. Indicates gating activity of the 4 mic/line channel

inputs.

Figure 2. EF2241 Front and Rear Panels

3 4 5612 7 9

11 1310 12 14 15

16

18

20

17

19

8

PRE-INSTALLATION

10. INPUT PARALLEL PORT. Parallel logic input.

11. O

UTPUT PARALLEL PORT. Parallel logic output.

12. EF B

US IN. Connects to EF BUS OUT of another Vortex device.

13. EF B

US OUT. Connects to the EF BUS IN of another Vortex device.

14. RS-232 S

ERIAL PORT. Connect this to an optional RS-232 remote control device,

such as a touch panel or personal computer COM port.

15. P

OWER SUPPLY INPUT. Connects to the external power supply provided with the

EF2241.

16. P

OWER AMPLIFIER OUTPUT. Drives up to 10 W into 4-16 Ohm speakers.

17. P

HONE/LINE JACKS. Use the PHONE jack for connecting an analog handset to the

system. Use the L

INE jack for connecting to an analog telephone line.

18. M

IC/LINE INPUTS. Connects to microphone at either mic or line level, with or

without phantom power.

19. L

INE INPUTS. Inputs A-D at line level.

20. L

INE OUTPUTS. Outputs 1-4 and Outputs A-D at line level.

Figure 3. Parallel remote control, EF B

US, serial remote control, power supply

input, and power amplifier output on back panel of the EF2241.

11 1310 12 14 15

16

Figure 4. Inputs and outputs on back panel of the EF2241.

18

20

17

19

INSTALLATION

VORTEX EF2241 Reference Manual 8 Technical Support: 800.932.2774

I

NSTALLATION

This equipment is intended to only be installed by qualified service personnel. The

equipment shall be connected to a socket-outlet that provides a protective earthing

connection.

North American

Requirement

CAUTION-To reduce the risk of fire, use only No. 26 AWG or larger telecommunica-

tion line cord.

M

OUNTING

THE

EF2241

The EF2241 can be mounted in a rack enclosure using four large screws (10-32x1/2”)

included with the unit. One EF2241 fits in a single rack space.

Recommendation

For Easy Access

While not required, leave a single rack space in between the EF2241 and other units

in your rack. This gives you easier access to the back panel.

Instructions for

Securing Power

Supply to Back of

EF2241

• Locate the cable clamp on the back panel of the EF2241 above the power con-

nector.

• Remove the screw and thread the power cord through the cable clamp.

• Attach the cable clamp to the back panel of the EF2241 and tighten the screw.

Align the clamp so that the power cable does not interfere with the connectors on

the EF2241 back panel.

• Plug in the power supply.

• We recommend that you also Ty-wrap the power supply to the rack. The purpose

of securing the power supply to the back panel is so that if the power supply were

to drop, it would pull where the cord is attached with the cable clamp and not pull

the plug out of the EF2241.

C

ONNECTING

THE

EF2241

TO

O

THER

E

QUIPMENT

Grounding The EF2241 has 4 mic/line inputs plus 4 line level inputs and 8 line level outputs.

Each input/output is “Pin 1 compatible” — this means that the ground pin of each

input/output is tied to chassis ground. Chassis ground is connected to the input power

ground.

Caution! Do not use any other power supply other than the one pro-

vided with this unit.

INSTALLATION

Typical EF2241

Connections

The EF2241 will typically be connected to other equipment in a single room setup as

shown below in Figure 5 and Figure 6.

The following steps are typically used to set up the EF2241:

• Connect a microphone to each of the 4 mic/line level inputs. The mic/line input

accepts mini-Phoenix connectors. See “Connector Pinouts” on page 51 for

pinouts of Phoenix connectors.

Figure 5. Block diagram of typical EF2241 connections: a single room using one EF2241.

Figure 6. Typical EF2241 connections.

Vortex

®

EF2241

In 1

In 2

In 3

In 4

Out 1

Out 2

Out 3

Out 4

Spk Out

Phone

EFBus Out

In A

In D

In C

In B

Out A

Out D

Out C

Out B

EFBus In

Polycom Video

CODEC

Line In Line Out

PSTN

Line

PSTN

Polycom Video Codec, 4-wire Connection

Vortex

®

EF2241

POLYCOM CODEC

TX RX

INSTALLATION

VORTEX EF2241 Reference Manual 10 Technical Support: 800.932.2774

• Connect speaker output to loudspeaker.

• If RS-232 remote control is desired, connect the RS-232 R

EMOTE CONTROL port

of the EF2241 to the remote control device, such as an RS-232 interface to a

touch panel or a COM port on a personal computer.

• Connect the L

INE RJ11 jack to an analog telephone line.

• Connect the P

HONE RJ11 jack to an analog telephone set (optional).

• Connect the external power supply to the P

OWER SUPPLY INPUT jack of the

EF2241.

• Set the country code on the EF2241. By default the phone interface will be dis-

abled until you select a country code for the telephony interface. This can either

be done with the front panel LCD menu, or the RS-232 interface. The country

code only needs to be selected the first time or when the country of the installa-

tion is changed.

D

EVICE

ID

S

ON

THE

EF B

US

When considering which Device IDs can be used for which Vortex device, decide

how many devices have the ability to transmit on the W, X, Y, and Z busses, and how

many have the ability to transmit on the P Bus. The EF2280, for example can only

transmit on the W, X, Y, and Z busses while the EF2241 can transmit on the W, X, Y,

and Z busses as well as the P bus. Up to 8 devices can transmit on the W, X, Y, and Z

busses. Similarly, up to 8 devices can transmit on the P bus. Note that the EF2241

counts as one of both types. All devices that can transmit on W, X, Y, and Z must

have unique device IDs. Vortex devices of the same type must have unique device

IDs. If the device IDs of linked Vortex devices are the same, the front panel LCD

screen will display “EFBus Error: Dev. ID Conflict”.

C

ONNECTING

M

ULTIPLE

V

ORTEX

D

EVICES

Up to 8 Vortex devices in combination can be linked together at one time (See Device

IDs on the EF Bus above). Each unit in the chain must have a unique Device ID. Use

the EF Bus to link multiple Vortex devices together.

The following steps should be followed to connect the EF Bus:

1. Set a unique Device ID for each Vortex device. The Device IDs range from 00 to

07.

2. Power off all units.

3. Connect the RS-232 remote control device to any Vortex device in the chain.

4. Connect the provided Cat-5 cable between the EF B

US OUT of the first device,

and the EF B

US IN of the second device.

5. Connect another Cat-5 cable between the EF B

US OUT of the second device and

the EF B

US IN of the third device, and so on.

6. Power on all units at the same time.

Note. The EF Bus must be connected so that the EF Bus In of one

box is connected to the EF Bus Out of another. Connecting

the EF Bus In to another EF Bus In (or Out to Out) will not

work.

INSTALLATION

Terminating the

EF2241

The EF2241 is self-terminating so if you are connecting multiple EF2241s, the EF

Bus does NOT need to be terminated. However, if you are linking the EF2241 to

EF2280s, terminate the EF Bus link.

F

ACTORY

D

EFAULT

S

ETTINGS

(P

RESET

0)

The following is a list of the factory default settings of the EF2241. Since the micro-

phones and other equipment in your application may have different nominal levels,

you can start with a F

ACTORY PRESET (Presets 0-15), change it to match your envi-

ronment and then save it within the EF2241 as a U

SER PRESET (Presets 16-47). Once

you’ve saved a U

SER PRESET, set the POWER ON PRESET to that USER PRESET (or

Figure 7. Only the EF2280 needs to be terminated when linked together with

EF2241s.

Vortex EF2280

EF Bus Terminator

...

Cat-5 cable

Vortex EF2280

Vortex EF2241

No Terminator Needed

INSTALLATION

VORTEX EF2241 Reference Manual 12 Technical Support: 800.932.2774

whichever preset you want to come up after power up). The unit will need to be con-

figured for your system.

PROGRAM PARAMETERS FACTORY DEFAULT PRESET VALUE

SYSTEM PARAMETERS

Preset 0

Device ID 0

AUTOMIX PARAMETERS

Chairman Mode Off

Decay Time 1000 ms

Hold Time 500 ms

Last Mic On Mode On (on Automixer 1)

Max NOM per Automixer 4

Off Attenuation -15 dB

INPUT CHANNELS

Acoustic Echo Cancellation On

Automatic Gain Control (AGC) On

AGC Rate 1 dB/s

AGC Max Gain 3 dB

AGC Min Gain -3 dB

Automixer 1

Echo Canceller Reference Ref1

Filtering Off

Gate Priority 1

Adaptive Threshold 10 dB

Gate Threshold Adaptive

Gating Auto

INSTALLATION

Presets and

Multiple Vortex

Devices

PRESET 0 is preconfigured for a system with multiple Vortex devices. In Preset 0,

microphones are bussed out to other units on the W Bus. Microphones are also input

into each device on the W Bus (I

NPUT WM0 in the Matrix).

If you have multiple devices in your system, save settings to a user preset (Presets 16-

47) on each device. Saving a preset will only save the preset on that particular unit.

Also, remember to set the P

OWER ON PRESET to the User Preset that you have saved

your settings to otherwise the device will revert back to Preset 0 (factory default) if

power is lost.

C

HECK

S

URROUNDING

E

QUIPMENT

Now that the physical connections to the EF2241 are set up, it may be necessary to

check the surrounding equipment to make sure levels are set correctly. The following

suggestions may be helpful in integrating the EF2241 into your system:

Pick a Standard

Signal Level

A standard nominal signal level should be used throughout the audio system. Any

equipment that does not operate at this standard level should be compensated for as

close to the piece of equipment as possible. A 0 dB nominal level is a good standard

signal level. For example, a consumer VCR will probably generate a -8 dBu level.

As soon as the VCR signal arrives at an input with some gain control, the input gain

should be adjusted so that you get a 0 dB level, i.e. adding 8 dB of gain.

Check Levels to

the Codec

Configure the matrix mixer output to the codec input. The output

gain of the matrix mixer should be set to match the nominal input level of the codec.

For example, if the codec accepts -10 dBV (-8 dBu) inputs, 8 dB of attenuation should

be applied at the matrix mixer output to the codec.

Input Gains Mic Mode + 15 dB = 48 dB for Inputs 1-4

0 dB for Inputs A-D

Manual Threshold 60 dB

Mute Off

Noise Cancellation On

Noise Cancellation Level 10 dB

Phantom Power On

OUTPUT CHANNELS

Mute Off

NOM Attenuation On for Outputs 1-4

On for Outputs A-D

Output Gain 0 dB

P

ROGRAM PARAMETERS FACTORY DEFAULT PRESET VALUE

INSTALLATION

VORTEX EF2241 Reference Manual 14 Technical Support: 800.932.2774

Configure the matrix mixer input from the codec output. The input

gain of the matrix mixer should be set to match the nominal output level of the codec.

For example, if the codec outputs a -10 dBV (-8 dBu) level, 8 dB of gain should be

applied on the matrix mixer input. This will bring the codec level up to 0 dBu inside

the matrix.

Verify Room Gain After adjusting the loudspeaker level, verify the room gain in your system using the

R

OOM GAIN meter on the DIAGNOSTICS page of Conference Composer. The Room

Gain measurement is only accurate when just the remote talkers are speaking. If local

talkers are speaking too, the room gain meters are not accurate. See Figure 8 below.

The meter shows the room gain, which is the relative level of the output level and the

input level. While the EF2241 will operate in positive room gain conditions, the

room gain should be around 0 dB or a negative value. If you have a positive room

gain, make adjustments in the following areas:

1. Decrease the Input Gain of the microphone.

2. Decrease the Output Gain of the microphone.

3. OR adjust the placement of the microphone relative to the loudspeaker.

Configure

Program Audio

Sources

Set the gains on the matrix mixer inputs from the program audio sources so that pro-

gram audio is played into the room at a level similar to that of speech from the remote

site. This should also ensure that the program audio levels are good when sent to the

remote site.

Figure 8. Room Gain Meter on the Diagnostics page of the Conference Composer

control software.

Room Gain Meter

Read Room Gain

from here

INTEGRATING THE EF2241 INTO YOUR SYSTEM

I

NTEGRATING

THE

EF2241

I

NTO

Y

OUR

S

YSTEM

Operating the

EF2241

The EF2241 can be operated in two ways: through the LCD menu on the front panel

or through RS-232. For control via RS-232, please refer to the EF2241 Programming

Guide, which includes programming tips as well as the EF2241 RS-232 commands.

For operation using the PC control software, Conference Composer, please refer to

the Conference Composer User Guide.

Use Conference Composer software to easily configure the EF2241 with a PC, or

refer to the Applications Guide for different configurations that are already pro-

grammed into factory presets.

I

NPUT

S

ETTINGS

Set Inputs 1-4 for

Mic or Line Level

Configure Inputs 1-4 for mic or line level using the LCD menu (See “Level” on

page 30) or Conference Composer Control Software (See the Conference Composer

User Guide).

Select Phantom

Power for Inputs

1-4

Turn phantom power On or Off for Inputs 1-4 using the LCD menu (See “Phantom

Power” on page 30) or Conference Composer Control Software (See the Conference

Composer User Guide). Phantom power should be turned On for condenser and elec-

tret microphones.

C

ALIBRATION

When using the factory default, Preset 0, the following calibration can be used.

Set Mic/Line

Input Channel

Gains

In Preset 0, Automatic Gain Control (AGC) is On and the microphone gains on Inputs

1-4 are set to 15 dB. The AGC will compensate for the microphone gain. If you are

using ceiling microphones, set the microphone gain to 28 dB.

Fine tune the Input Gain using the Automatic Gain Control (AGC)

meter on Conference Composer Software.

In the Conference Composer

Software, go to the D

IAGNOSTICS page. Watch the meter labelled AGC while someone

is talking into the particular channel that you are adjusting. Watch the number in the

box at the bottom of the AGC meter (See Figure 9 below). This is the amount of gain

that the AGC is applying. The goal is to have the AGC meter on average staying

around 0. If the level that you see in the box is negative, decrease the input gain by

the average number that you see in the box because the AGC is attenuating the chan-

nel’s input gain because the level is too high. If the number in the box is positive,

increase the input gain on that channel because the AGC is boosting the signal

because it is too low. For example, if the meter is showing an average gain of -15 dB,

INTEGRATING THE EF2241 INTO YOUR SYSTEM

VORTEX EF2241 Reference Manual 16 Technical Support: 800.932.2774

you should increase your input gain by 15 dB. If the meter shows an average gain of

+10 dB, you should decrease your input gain by 10 dB.

Set Levels on Line

Input Channels

Set the line input channel gains (Channels A-D) to match the nominal level of the

incoming equipment. The line inputs have a maximum nominal level of 0 dBu. If

your incoming line level inputs have a higher nominal level than 0 dBu you will want

to use a pad to remove the level.

If you are connecting from equipment that has RCA plugs, you will most likely need

8 dB of gain on the Input and -8 dB of gain on the Output.

Figure 9. AGC Meter on the Diagnostics page of the Conference Composer soft-

ware. The gain adjustment is the same gain control on the Mic/Line Inputs page in

Conference Composer.

I

F THE AGC METER SHOWS... ADJUST THE INPUT GAIN IN THIS WAY.

positive gain Increase gain by the level

shown in the box.

negative gain Decrease gain by the level

shown in the box.

an average level of 0 dB You’ve set the Input Gain

to a good level!

Table 1: How to set the Input Gain using the AGC meter on the Conference

Composer Diagnostics page.

AGC Level Meter

Read AGC level

Adjust Input Gain here

INTEGRATING THE EF2241 INTO YOUR SYSTEM

Customize

Setting for Your

Particular

Application

The following sections will describe customizing parameters on the EF2241 for your

particular application if you are not using Preset 0.

S

ET

UP

THE

P

HONE

I

NTERFACE

The echo canceller reference of the EF2241 is by default set up with the phone input

already assigned to it.

By default the phone interface will be disabled until you select a country code for the

telephony interface. This can either be done with the front panel LCD menu, or the

RS-232 interface. The country code only needs to be selected the first time or when

the country of the installation is changed.

Send audio from the phone to the outputs on the same device by unmuting the cross-

point of Input T on that output. Send audio from the phone to other linked devices by

using the P bus output in the EF Bus. The linked devices can take the phone signal

off the bus from the P Bus input.

B

UILD

Y

OUR

E

CHO

C

ANCELLER

R

EFERENCE

The acoustic echo canceller (AEC) reference should generally contain exactly the

same audio signals as what is coming out of your loudspeaker(s), since the signal out-

put from the loudspeaker is what is then picked up by the room’s microphones caus-

ing acoustic echo. Note that this statement is a general statement. Conditions for this

being true follow:

If your system

does NOT have

sound

reinforcement,

• The AEC reference should contain exactly the same audio as the loudspeaker

output: all far end audio, audio from the phone add, program audio, etc.

• If your system contains stereo inputs and outputs, the reference must contain a

mix of both stereo inputs. For example, if your VCR audio is in stereo, the refer-

ence should contain both the left and right signals each attenuated by 3 dB, as

well as any other audio that is going to your loudspeaker.

• If you are using crosspoint gains in the loudspeaker mix, apply the same gains to

the signals in your reference.

If your system

has sound

reinforcement,

• Do NOT mix your room microphones into the reference, but include all other

audio (program audio, remote audio, phone audio, etc.).

E

CHO

C

ANCELLER

R

EFERENCE

FOR

M

ULTIPLE

V

ORTEX

D

EVICES

In a system with multiple devices, we recommend that one device be designated as

the unit that provides the EF bus reference for the acoustic echo cancellers. This unit

takes one of its reference signals (either Ref 1 or Ref 2) and places it on the EF bus.

All other units that are linked together may use the EF bus reference as the reference

INTEGRATING THE EF2241 INTO YOUR SYSTEM

VORTEX EF2241 Reference Manual 18 Technical Support: 800.932.2774

for their echo canceller, or they can use their own internal references. The references

may include a mix of any input, with crosspoint gains, including W, X, Y, and Z bus-

ses. Set the EF Bus Reference in the System Menu of the LCD Menu (See “EF Bus

Reference” on page 28).

Setting up the

Bus Reference

If all far end audio and program audio sources are on the same

Vortex device,

1. Assign far end audio and program audio sources to Reference 1 on the originat-

ing device.

2. On the EF Bus page in Conference Composer for the originating device, set the

Exported Signals to R

EFERENCE 1. Only one device can put an echo canceller

reference on the EF Bus as the Bus Reference.

3. On all linked devices, set the echo canceller reference to B

US.

For example, a system uses 1 EF2241, 1 EF2280, and 1 Polycom VS4000 video

codec. The Reference 1 is set up on EF2280 with ID 0. The Matrix for this EF2280

in Conference Composer is shown in Figure 10 and the EF Bus page in Figure 11.

Conference Composer will not allow more than one device assign their echo canceller

reference as the Bus Reference. Notice that the phone audio and VS4000 inputs are

both assigned to Reference 1 on the originating EF2280. The Matrix for any linked

devices is shown in Figure 12.

Figure 10. Matrix page of origin EF2280 (ID 00) Figure 11. EF Bus page of origin EF2280 (ID 00)

Page is loading ...

Polycom EF2241 User manual

This manual is also suitable for

Polycom EF2241 User manual

Related papers

Other documents