Zeta PBTA-200 User manual

Brand: Zeta

Model: PBTA-200

Type: User manual

Zeta PBTA-200 is a battery-powered temporary fire alarm that can be activated manually by pressing the button on the front of the device. Once activated, the unit will sound an alarm and flash a strobe light. It can be used as a standalone alarm or interconnected with up to 32 other units, so that when one alarm is activated, all of the connected alarms will sound. The Zeta PBTA-200 is easy to install and can be mounted on a wall, ceiling, or any other surface. It is also weatherproof and can be used both indoors and outdoors.

Zeta PBTA-200 is a battery-powered temporary fire alarm that can be activated manually by pressing the button on the front of the device. Once activated, the unit will sound an alarm and flash a strobe light. It can be used as a standalone alarm or interconnected with up to 32 other units, so that when one alarm is activated, all of the connected alarms will sound. The Zeta PBTA-200 is easy to install and can be mounted on a wall, ceiling, or any other surface. It is also weatherproof and can be used both indoors and outdoors.

PBTA-200 User Manual

Issue #1 Issue Date XX/XX/XXXX Revision #1

User Manual /

PBTA-200

PBTA-200 User Manual

Issue #1 Issue Date XX/XX/XXXX Revision #1

Contents

Section 1 Introduction 3

Section 2 Power Supply 3

Section 3 Typical Wiring Diagram

3

Section 4 Installation 4

Section 5 Technical Speciﬁcation

5

Contents /

2

PBTA-200 User Manual

Issue #1 Issue Date XX/XX/XXXX Revision #1

1 Introduction

The PBTA-200 push button temporary ﬁre alarm is activated immediately by pressing the

“mushroom” button ﬁxed to the front of the device. Once activated the unit will sound & ﬂash.

It can be used as a standalone alarm or interconnected in series.

2 Power Supply

The unit is powered by 8 AA batteries.

3 Typical Wiring Diagram

The following diagram shows 3 units connected in series where one alarm activation will trigger

all connected units.

Section 1 Introduction / Section 2 Power Supply / Section 3 Typical Wiring Diagram /

Fig.1

3

PBTA-200 User Manual

Issue #1 Issue Date XX/XX/XXXX Revision #1

4 Installation

Battery Installation

Install batteries as shown in ﬁgures 2 & 3 above (note that the battery sign is shown on battery

box).

Alarm Installation

It can be installed on boards, walls or wherever it can be hung (these should be places where

the unit is easily visible). Fix the screw according to ﬁgure 4 and complete the installation

according to ﬁgure 5.

Fig.2 Fig.3

Fig.4 Fig.5

4

PBTA-200 User Manual

Issue #1 Issue Date XX/XX/XXXX Revision #1

5 Technical Speciﬁcation

Operating Voltage 8 x AA batteries (12V DC)

Average Current

10uA

Alarm Current 200mA

Sound Output 95 db @ 3m

Strobe Colour Red

Operating Temperature

-10°C to +50°C

Minimum Continuous Temperature

0°C

Maximum Humidity 95% RH Non Condensing

Alarm Activation

Manual (press “mushroom” button)

Reset

Manual (twist “mushroom” button)

Number of Interlinked Units 32

IP Rating

IP35

Size, Width x Height x Diameter

230mm x 230mm x 104mm

Weight (Including Batteries)

650g (850g)

5

1
2
3
4
5
6

Zeta PBTA-200 User manual

Brand: Zeta

Model: PBTA-200

Type: User manual

Zeta PBTA-200 is a battery-powered temporary fire alarm that can be activated manually by pressing the button on the front of the device. Once activated, the unit will sound an alarm and flash a strobe light. It can be used as a standalone alarm or interconnected with up to 32 other units, so that when one alarm is activated, all of the connected alarms will sound. The Zeta PBTA-200 is easy to install and can be mounted on a wall, ceiling, or any other surface. It is also weatherproof and can be used both indoors and outdoors.

Related papers

Other documents