Soundstream iCQ.2 Operating instructions

Type
Operating instructions

Soundstream iCQ.2 is an innovative line output converter that bridges the gap between your factory head unit and aftermarket amplifier, delivering an unparalleled audio experience.

With its versatile design, the iCQ.2 seamlessly integrates into various systems. It features high-level inputs that can handle up to 100 watts of speaker-level input at 4 ohms, making it compatible with a wide range of factory head units.

The iCQ.2 boasts an impressive maximum output voltage of 11.1v, ensuring a powerful and dynamic sound reproduction. Its remote turn-on output conveniently powers your amplifier, eliminating the need for additional wiring.

Soundstream iCQ.2 is an innovative line output converter that bridges the gap between your factory head unit and aftermarket amplifier, delivering an unparalleled audio experience.

With its versatile design, the iCQ.2 seamlessly integrates into various systems. It features high-level inputs that can handle up to 100 watts of speaker-level input at 4 ohms, making it compatible with a wide range of factory head units.

The iCQ.2 boasts an impressive maximum output voltage of 11.1v, ensuring a powerful and dynamic sound reproduction. Its remote turn-on output conveniently powers your amplifier, eliminating the need for additional wiring.

OPERATING MANUAL
LINE OUTPUT CONVERTER
iCQ.2
WWW.SOUNDSTREAM.COM
Thank you for choosing SOUNDSTREAM. Designed and engineered in the USA, this product com-
bines innovative technology with the finest materials to consistently deliver Absolutely State of
the Art performance, sound quality, reliability, and value. This SOUNDSTREAM product reflects our
commitment to offer you unparalleled performance and quality for years of dependable service
and listening enjoyment.
WELCOME TO SOUNDSTREAM
FOR BEST PERFORMANCE PLEASE HAVE YOUR SOUNDSTREAM PRODUCT IN-
STALLED BY AN AUTHORIZED SOUNDSTREAM DEALER
WWW.SOUNDSTREAM.COM WWW.SOUNDSTREAM.COM
While many line output converters are available. We thank you for choosing Sound-
stream. The advantage to using the iCQ.2 is that we use the nest quality parts available
for unmatched sound qulaity.
Most factory headunits are designed to roll the lower frequencies off when the volume
increases to save the factory speakers. The iCQ.2 will keep constant voltage so at any
volume level the sound remains constant as the volume gores up, with no roll off. This re-
sults in the best possible sound at any level.
LINE OUTPUT DIAGRAM
The diagram below show a typical installation using the iCQ.2 line output converter. Your
system may very slightly.
INSTALLATION
The Power Connection (12v+ and Ground) should be made with minimum 18g wire. The 12v+
terminal should be connected to 12v positive with a 1A fuse between the iCQ.2 and the power
source.
The GND terminal should be connected to chasis ground and should have a ring terminal
crimped. The terminal should be connected to chasis ground where all piant and grease has
been removed for maximum contact.
Remote In- This wire should be connected to the amplier turn on wire if equipped. If not amplier
trun on is available hook the wire to 12v+ switched power. This should show 12v+ ONLY when the
key is on.
Remote Out- The iCQ.2 is equipped with a remote 12v+ output for turning on the aftermarket am-
plier. Connect this terminal to the Remote Turn On of the amplier.
LINE INPUT DIAGRAM
The diagram shows a typical installtion
using the iCQ.2 as a line driver.
WWW.SOUNDSTREAM.COM
WWW.SOUNDSTREAM.COM
A
B
C
D
E
F
A. Power Connection. 12v+ , Ground, Remote turn on are made here. Use minimum of 18g wire.
Check to make sure all connections are secure. Failure to do so may result in damage to the iCQ.2
B. RCA Output to aftermarket amplier. Maximum output voltage up to 11v.
C. High level inputs from amplier. Up to 100watts of input at 4 ohm.
D. Gain control
E. Power LED indicator
F. Clipping indicator
iCQ.2 FEATURES
All Aluminum chasis
Signal Sense and manual Turn on modes
Max output 11.1v
100wats of speaker level input at 4ohms
Remote turn on output
Clipping LED indicator
Remote gain control
AUX input
Dimensions 4.5”x1”x4.5”
FOR BEST PERFORMANCE PLEASE HAVE YOUR SOUNDSTREAM PRODUCT IN-
STALLED BY AN AUTHORIZED SOUNDSTREAM DEALER
AUX Input is activated by a switch located on the top of the iCQ.2.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Soundstream iCQ.2 Operating instructions

Type
Operating instructions

Soundstream iCQ.2 is an innovative line output converter that bridges the gap between your factory head unit and aftermarket amplifier, delivering an unparalleled audio experience.

With its versatile design, the iCQ.2 seamlessly integrates into various systems. It features high-level inputs that can handle up to 100 watts of speaker-level input at 4 ohms, making it compatible with a wide range of factory head units.

The iCQ.2 boasts an impressive maximum output voltage of 11.1v, ensuring a powerful and dynamic sound reproduction. Its remote turn-on output conveniently powers your amplifier, eliminating the need for additional wiring.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI