BEGLEC LED NEON FLEX Owner's manual

BEGLEC
Brand
BEGLEC
Model
LED NEON FLEX
Category
Coffee making accessories
Type
Owner's manual

This manual is also suitable for

Version: 1.0
WWW.BRITEQ-LIGHTING.COM
Copyright © 2009 by BEGLEC comm.v.a.
‘t Hofveld 2 ~ B1702 Groot-Bijgaarden ~ Belgium
Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.
LED
NEONFLEX
Operation Manual
Mode d'emploi
Gebruiksaanwijzing
Bedienungsanleitung
Manual de instrucciones
Manual do utilizador
EN
FR
NL
DE
ES
PT
EN - DISPOSAL OF THE DEVICE
Dispose of the unit and used batteries in an environment friendly manner
according to your country regulations.
FR - DÉCLASSER L’APPAREIL
Débarrassez-vous de l’appareil et des piles usagées de manière écologique
Conformément aux dispositions légales de votre pays.
NL - VERWIJDEREN VAN HET APPARAAT
Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke
manier conform de in uw land geldende voorschriften.
DU - ENTSORGUNG DES GERÄTS
Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und
Weise gemäß den Vorschriften Ihres Landes.
ES - DESHACERSE DEL APARATO
Reciclar el aparato y pilas usadas de forma ecologica conforme a las
disposiciones legales de su pais.
PT - COMO DESFAZER-SE DA UNIDADE
Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em
conformidade com as normas vigentes no seu país.
ENGLISH OPERATION MANUAL
BRITEQ
®
1/24 LED NEONFLEX
OPERATION MANUAL
Thank you for buying this BRITEQ
®
product. To take full advantage of all possibilities and for your own
safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
This device was designed to produce decorative effect lighting and is used in light show systems.
This LED technology based Neonflex is a perfect direct replacement for the traditional glass neon. It can
be used in all kinds of applications like architectural design, cove light, commercial displays ( signs,
letters), etc. Some of its huge benefits are:
o
Visually identical to glass neon but 100% unbreakable.
o
Up to 90% energy and cost saving compared to glass neon (only 4W/m)
o
Due to use of high voltage (15kV) glass neon needs a highly specialized installer. Installing LED
Neonflex is very easy and cheap!
o
The highly flexible PVC jacket (Rmin = 4cm) can be easily bended to make letters, logos, etc.
o
Lengths up to 95m can be used to make nice borders and curves on walls, buildings, entrances, etc.
o
Several accessories available for easy installation.
o
Sold per unit length: 1,52m for RED or 0,91m for BLUE
BEFORE USE
Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
Operating instructions
LED NEONFLEX (sold by unit length)
SAFETY INSTRUCTIONS:
CAUTION
CAUTION: To reduce the risk of electric shock, do not
remove the top cover. No user-serviceable parts inside.
Refer servicing to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
ENGLISH OPERATION MANUAL
BRITEQ
®
2/24 LED NEONFLEX
To protect the environment, please try to recycle the packing material as much as possible.
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
This unit is for indoor use only.
Keep the unit away from children.
Inexperienced persons should not operate this device.
Maximum save ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
Always unplug the unit when it is not used for a longer time or before to start servicing.
The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
Check that the available voltage is not higher than the one stated in the specifications of this installation
manual.
The power cord should always be in perfect condition. Switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Never let the power-cord come into contact with other cables!
Don’t connect the unit to any dimmer pack.
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
The unit must be replaced if they are visibly damaged.
Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
INSTALLATION:
WARNING: To avoid damage or electrocution: Never drill holes, or place nails or screws direct in the
Led Neonflex!
Adjusting the length:
Cut the Led Neonflex at the desired length. Be careful to cut only on the
indicated marks.
Fixing the power cord:
1. Insert the connector pins in the Led Neonflex tube.
2. Apply silicon glue in the gap between the Neonflex tube and the connector pins.
3. First slide the heatschrink over the Neonflex tube. Now insert the Neonflex tube in the plastic sleeve
of the power cord.
4. Add PVC glue to fix the plastic sleeve of the power cord to the Neonflex tube.
5. Apply silicon glue in the gap between the plastic sleeve of the power cord and the Neonflex tube.
6. Cover with the heat shrinkable tube and shrink with a heat-blower.
1. 2. 3.
This symbol means: Safety Class II appliance
This symbol determines: the minimum distance from lighted objects. The minimum distance
between light-output and the illuminated surface must be more than 1 meters
The device is suitable for mounting on standard flammable surfaces. Standard flammable
surfaces include building materials such as wood and wood-based materials more than 2mm
thick.
ENGLISH OPERATION MANUAL
BRITEQ
®
3/24 LED NEONFLEX
4. 5. 6.
Fixing the L-Connector:
Use the same method as for the power supply cable (description above)
Fixing the Middle-Connector:
Use the same method as for the power supply cable (description above)
Fixing 2 ends together with the Splice Connector:
1. First slide the heatschrink over one of the Neonflex tubes.
Insert the connector pins in one of the Led Neonflex tubes and press both tubes together.
2. Apply silicon glue to fill up the gap between the two Neonflex tubes.
3. Cover with the heat shrinkable tube and shrink with a heat-blower.
1. 2. 3.
Fixing the end cap:
1. Add silicon glue to the end cap
2. Place the end cap over the Led Neonflex tube.
1. 2.
Fixing the Led Neonflex with the alu mounting strips:
The ALU strips are sold in 1meter lengths: you can cut these to the size you like.
First fix the alu strips to the wall, then you can place the Neonflex tube inside.
For curved installations, you can use smaller parts of the alu strip.
Warning: never bend the Led Neonflex with a diameter that is inferior to 40mm !
ENGLISH OPERATION MANUAL
BRITEQ
®
4/24 LED NEONFLEX
OPERATING INSTRUCTIONS
Once connected to the mains the device starts running.
Always unplug the unit when it is not used for a longer time or before start servicing.
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
SPECIFICATIONS
Mains Infput AC 230V, 50Hz
Roll length 50,29m
LED spacing 0,5”
Total n° of LEDs 3960
Total Watts 198W
Watts per Meter 4 W/m
Color Red Blue
Light output (Lm / m) 8,34 4,8
N° of leds per unit 120 72
Unit length for cutting 1,52m 0,91m
Max loading length
with 1.6A power cord
97m 96m
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

BEGLEC LED NEON FLEX Owner's manual

BEGLEC
Brand
BEGLEC
Model
LED NEON FLEX
Category
Coffee making accessories
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents