iTEC U3METALDOCK User guide

Brand: iTEC

Model: U3METALDOCK

Category: Notebook docks & port replicators

Type: User guide

Page is loading ...

i-tec Power Bank 5200 mAh Advance - white

P/N: PB5200

?A portable battery with a capacity of 5200 mAh

?For charging of mobile phones, GPS

navigators, tablets, music players and other

digital devices

?Ideal solution for travelling where you cannot

recharge your devices from the mains

?5 LED diodes indicating the current battery

capacity level

?Control by a single ON/OFF button

?Supplied with 3-In-1 USB cable (Apple / Micro /

Mini)

i-tec USB 3.0 Metal Charging HUB 10 Port

P/N: U3HUBMETAL10

i-tec USB 3.0 Metal Charging HUB 7 Port

P/N: U3HUBMETAL7

i-tec USB 3.0 Metal Charging HUB 4 Port

P/N: U3HUBMETAL4

?10x / 7x / 4x USB 3.0 port

?Compatible with USB 2.0 / 1.1

?USB charging detection mechanism for

mobile devices for all 10 / 7 / 4 ports

?Plug & Play

?Power adapter

i-tec USB 3.0 HUB 4 Port

P/N: U3HUB401

?4x USB 3.0 port

?Compatible with USB 2.0 / 1.1

?Plug & Play

?Passive HUB without power adapter

Recommended products

Read carefully the user manual before assembly - installation - commissioning.

Protect yourself and avoid damaging your equipment.

Lesen Sie unbedingt die Gebrauchsanweisung vor Aufstellung – Installation –

Inbetriebnahme. Dadurch schützen Sie sich und vermeiden Schäden an Ihrem Gerät.

Peèlivì si pøeètìte uživatelskou pøíruèku pøed montáží – instalací – uvedením do

provozu. Ochráníte tím sebe a vyvarujete se poškození Vašeho zaøízení.

Przeczytaj uwa¿nie instrukcjê przed monta¿em / pod³¹czeniem / u¿ytkowaniem, aby

ustrzec siê przed obra¿eniami a urz¹dzenie przed uszkodzeniem.

Každopádne si preèítajte užívate¾skú príruèku pred zložením - inštaláciou - uvedením

do prevádzky. Ochránite sa tým a vyvarujete sa škodám na Vašom prístroji.

Prieð montavimà-instaliavimà-eksploatavimà iðsamiai perskaitykite vartotojo vadovà.

Tuo apsaugosite save ir iðvengsite Jûsø árenginio paþeidimo.

i-tec USB 3.0 Metal Docking Station

ENGLISH..................................................................................................... 05-08

DEUTSCH................................................................................................... 09-12

ÈESKY........................................................................................................ 13-16

POLSKI....................................................................................................... 17-20

SLOVENSKY...............................................................................................21-24

LIETUVOS................................................................................................... 25-28

DECLARATION OF CONFORMITY................................................................. 29

WEEE............................................................................................................... 30

INTRODUCTION

Thank you for purchasing the i-tec docking station that will enable you easy and fast connection of your

favorite hardware equipment to your notebook / tablet / PC using a single USB cable.

The docking station is furnished with a DVI-I, a HDMI and a Display port for connecting of an external monitor

or data projector. However, only two of these ports can be used simultaneously – the DVI-I and either the

HDMI or the Display port. In case of simultaneous connection of monitors to the HDMI and the Display

port the docking station will automatically give preference to the Display port and the HDMI port will be

disconnected. This means that only the equipment connected to the Display port will be active / functional.

You can use modern plasma or LCD monitors and TV sets as the display equipment. The graphic chip, which

makes the heart of the docking station, supports a resolution of 2560 x 1600 pixels for the Display port and the

Full HD+ (2048 x 1152 pixels) resolution for the DVI / HDMI port.

You can use the USB 3.0 port for connecting a keyboard, a mouse, an external disk, a printer and other

peripheries. All three USB 3.0 ports have a function of standard charging. Charging as per the BC 1.2

specification (for iPad and Samsung tablets) is possible only from the USB 3.0 port on the back panel of the

docking station.

The Gigabit Ethernet port will allow you to connect internet modem / LAN Ethernet network for faster data

transfer. The docking station is also equipped with input for headphones and microphone allowing

connection of an audio system.

The docking station features a compact and elegant metallic design which was developed in accordance with

the ultrabook line. It can be used also in the horizontal position as a notebook or tablet pad providing better

circulation of air under these pieces of equipment. In this case you can stick two pieces of protective anti-slip

strips that are included in the package on top of the docking station.

CONTENT OF THE PACKAGE

?i-tec USB 3.0 docking station

?Power adapter

?USB 3.0 cable (one end connector type A, the second end type B; 100 cm) – for connecting to a

notebook / PC

?CD with the drivers and the manual

?Quick Start

SYSTEM REQUIREMENTS

Hardware requirements: notebook / tablet with OS Win 8 / PC with a free port USB 3.0 / 2.0. If you have

USB 2.0, the data transfer speed will be reduced. Procesor CPU 2.0 GHz Dual Core and higher Intel

Pentium/Celeron or AMD, memory 2GB RAM.

Operating system: Windows XP SP3 / Vista / 7 / 8 / 8.1 32/64 bit, Mac OS X.

For playing a DVD on an additional monitor the processor shall be at least Intel Pentium 2.0 and higher, 1

GB RAM and a screen resolution shall be 800x600 and 16 colors.

CAUTION!

Charging: The docking station supports charging of the connected USB mobile equipment such as

smartphones, ebook readers, multimedia players, GPS navigations and tablets (e.g. Asus, Toshiba, Dell,

GoClever, Prestigio, Emgeton, Sencor). Simply connect the equipment you want to charge using the original

cable to the USB port of the docking station. The only exceptions are the Apple or Samsung tablets which are

supported as well, but only on the USB port with the BC 1.2 specification on the back panel of the docking

station. At the same time the docking station must be disconnected from the computer/notebook and

the inclosed power adaptor must be connected.

i-tec USB 3.0 Metal Docking Station

LISH

USB 3.0: Before the installation on the USB 3.0 port make sure that you have the most recent drivers installed

for this port (for the USB 3.0 controller into notebook / tablet / PC). Products with the USB 3.0 SuperSpeed

technology have been used since 2010; however, the drivers for the supported equipment are still undergoing

some fine tuning. Your notebook / tablet / PC needs to be equipped with the USB 3.0 interface so that you can

utilize the advantages of the fast USB 3.0 equipment. Its problem free function is ensured by the chipset which

needs to have the current drivers available.

Problems that you can encounter during the installation or use of our USB 3.0 equipment are very often caused

by the installed outdated drivers for the USB 3.0 controller or chipset of your notebook / tablet / PC. Other

problems can be caused by outdated firmware of the USB 3.0 port controller. Most frequently it is one of the

following manufacturers: Intel, Renesas (former NEC), Via (VLI), AS Media, Fresco Logic, Etron.

You can find the most recent drivers for the i-tec products on our website www.i-tec-europe.eu in the

„Download“ tab for the individual products. The „Problems with USB 3.0“ tab includes a more detailed

description with links to the drivers and firmware for USB 3.0 controllers.

Note:

?The installation of audio ports, reader and the USB HUB (for USB 3.0 ports type A) is automatic from the

system, the other ports need to be installed from the supplied CD.

?Before the first connection of the docking station to a notebook / tablet / PC it is necessary first to install

the LAN and DVI-I / DP / HDMI port from the supplied CD and only then to connect the equipment to the

docking station.

INSTALLATION OF DRIVERS IN WINDOWS XP SP3 / VISTA / 7 / 8 / 8.1 (32/64 BIT VERSION)

Before the first use do not connect the docking station to the notebook / tablet / PC, until you install the

corresponding drivers for the LAN and DVI-I / DP / HDMI port from the supplied CD. The equipment drivers

need to be installed only before the first use.

Insert the CD with the drivers to the CD drive or download the required software from our website www.i-tec-

europe.eu from the „Download“ tab for this product. Install the drivers according to the following procedure:

For the LAN and DVI-I / DP / HDMI port select the installation from the Setup.exe file in the directory on the CD:/

or run the downloaded file, select the language of the installation and follow the instructions on the screen.

Note:

In Windows Vista / 7 / 8 / 8.1 install the DVI-I / DP / HDMI port as the „Administrator“. The monitor may be

flashing during the installation of the drivers – this is a standard process. After the completion of the installation

we recommend restarting the notebook / tablet / PC.

HARDWARE INSTALLATION (CONNECTING THE DOCKING STATION TO A NOTEBOOK / TABLET / PC)

1) Turn ON the notebook / tablet / PC and connect the power adapter to the docking station.

2) Connect the power adapter to the AC 110 V / 230 V mains.

3) Connect the USB 3.0 cable to the USB port type B on the back on all of the docking station.

4) Connect the USB 3.0 cable to a free USB 3.0 / 2.0 port of your notebook / tablet / PC.

5) Subsequently, the automatic installation of the ports in the individual systems will start.

6) After the completion of the installation restart the notebook / tablet / PC.

INSTALLATION OF DRIVERS IN MAC OS X

Before the first use do not connect the docking station to the MacBook / PC, until you install the corresponding

drivers for the LAN and DVI-I / DP / HDMI port from the supplied CD. The equipment drivers need to be

installed only before the first use.

Quick Start

GLI

E H

Insert the CD with the drivers to the CD drive or download the required software from our website www.i-tec-

europe.eu from the „Download“ tab for this product. Install the drivers according to the following procedure:

For the LAN and DVI-I / DP / HDMI port select the installation from the DisplayLink_MacOSX.dmg file in the

directory on the CD:/ or run the downloaded file. Decompress the file on the desktop of your MacBook / PC as a

virtual disc, select “Drivers“ and then „DisplayLink Software Installer“. Then select the language of the

installation and follow the instructions on the screen. Enter the user password if necessary.

The monitor may be flashing during the installation of the drivers – this is a standard process. After the

completion of the installation restart the MacBook / PC.

HARDWARE INSTALLATION (CONNECTING THE DOCKING STATION TO A MACBOOK / PC)

1) Turn ON the MacBook / PC and connect the power adapter to the docking station.

2) Connect the power adapter to the AC 110 V / 230 V mains.

3) Connect the USB 3.0 cable to the USB port type B on the back panel of the docking station.

4) Connect the USB 3.0 cable to a free USB 3.0 / 2.0 port of your MacBook / PC.

5) Subsequently, the automatic installation of the ports in the individual systems will start.

6) After the completion of the installation restart the MacBook / PC.

FREQUENTLY ASKED QUESTIONS

Question: What are the primary graphics card requirements for DisplayLink chipsets in i-tec graphic adapters

and docking stations?

Answer: DisplayLink graphic chipsets are secondary displays. There currently needs to be a primary graphics

card in the system. Windows XP: Under Windows XP, DisplayLink install their own virtual graphics adapters

under device manager and Windows Display Properties. These are independant of the primary graphics card.

Windows Vista and later: Under windows Vista onwards, the DisplayLink graphics driver works closely with

the primary graphic card. DisplayLink works with all Intel, NVidia, ATI/AMD, NVidia and VIA graphics cards.

DisplayLink do not support the SiS or Matrox graphics cards.DisplayLink may not work if there are multiple

graphics cards installed in the PC. DisplayLink does not support ATI crossfire or NVIDIA SLI configurations.

NVIDIA GeForce Go 7700/7900 from v6.3 software. If using DisplayLink with these graphics card, please use

an earlier software release.

Question: After installation of Windows 8.1 the equipment stopped functioning. In Windows 8 it worked

without problems.

Answer: Please install the most recent drivers from our website that you can find in the „Download“ tab for the

given product. Windows 8.1 is supported from the DisplayLink 7.4 version.

Question: After installation of Mac OS X 10.9 Mavericks the equipment stopped functioning. In the previous

system version the equipment worked without problems.

Answer: Please install the most recent drivers from our website that you can find in the „Download“ tab for the

given product. Mac OS X 10.9 Mavericks is supported from the DisplayLink 2.1 version.

Question: I am using Mac OS X and the audio output is not functioning.

Answer: The current drivers for Mac OS X do not support audio when the equipment is connected to the USB

3.0 port. Audio can be used only when the equipment is connected to the USB 2.0 port.

Question: The docking station is not functioning with a tablet and Windows 8.

Answer: Please install the most recent drivers 7.2 M0 or higher that can be downloaded from

http://www.displaylink.com/support/index.php.

LISH

i-tec USB 3.0 Metal Docking Station

Question: I have a problem with detecting the USB 3.0 docking station in the USB 3.0 port of my notebook /

tablet / PC.

Answer: The problem may be caused by outdated drivers for the USB 3.0 port of your notebook / tablet / PC.

Please read the description and download the most recent drivers for the USB 3.0 chipset in your notebook /

tablet / PC and installed them according to the instructions provided. The drivers can be downloaded from

http://www.displaylink.com/support/ticket.php?id=315.

Question: How to properly install the USB 3.0 docking station in Windows?

Answer: Do not connect the USB 3.0 docking station to the USB port of your notebook / tablet / PC until you

install the drivers. You need to install the most recent drivers for the DisplayLink (for internal chipset DL-3700)

that you can download from http://www.displaylink.com/support/index.php. After you have installed the

drivers and connected the USB 3.0 docking station to the USB port of your notebook / tablet / PC the remaining

drivers will be installed automatically. The control utility will be activated only after connecting the monitor.

Question: Are there drivers for Windows 8 / 8.1 32/64 bit for the USB 3.0 docking station available?

Answer: Yes, for the graphic part you need to install the most recent drivers for the DisplayLink (for internal

chipset DL-3900) that you can download from http://www.displaylink.com/support/index.php. Do not connect

the USB 3.0 docking station until you install these drivers. After you have installed the drivers and connected

the USB 3.0 docking station to the USB port of your notebook / tablet / PC the remaining drivers will be installed

automatically. The control utility will be activated only after connecting the monitor.

Question: Can I get more detailed information on troubleshooting for the USB 3.0 docking station?

Answer: Of course, you can find useful information on the DisplayLink website at

http://www.displaylink.com/support/knowledgebase.php on the FAQ tab or you can contact our technical

support.

Question: The equipment will not charge an Apple / Samsung tablet.

Answer: Charging is supported only on one USB 3.0 port on the back panel of the docking station with the BC

1.2 specification. At the same time the docking station must be disconnected from the computer / notebook

and the included power adaptor must be connected to the docking station.

If some of the accessories specified on the carton is missing in the package, please contact us with a

request for delivering the missing accessory by e-mail at [email protected], and indicate the delivery

address.

For more information, please refer to the User’s Manual on the provided CD-ROM.

Quick Start

GLI

E H

Page is loading ...

Note: Marking is in compliance with EU Directive 2002/96/EC and EN50419

English

This equipment is marked with the above recycling symbol. It means that at the end

of the life of the equipment you must dispose of it separately at an appropriate

collection point and not place it in the normal domestic unsorted waste stream. This

wil benefit the environment for all. (European Union only)

Deutsch

Dieses Produkt trägt das Recycling-Symbol gemäß der EU-Richtinie 2002/96/EC.

Das bedeutet, dass das Gerät am Ende der Nutzungszeit bei einer kommunalen

Sammelstelle zum recyceln abgegeben werden muss, (kostenloss). Eine

Entsorgung ûber den Haus-/Restmûll ist nicht gestattet. Dies ist ein aktiver Beitrag

zum Umweltschutz. (Nur innerhalb der EU)

Èeština

Toto zaøízení je oznaèeno výše uvedeným recyklaèním symbolem. To znamená,

že na konci doby života zaøízení musíte zajistit, aby bylo uloženo oddìlenì na

sbìrném místì, zøízeném pro tento úèel a ne na místech urèených pro ukládání

bìžného netøídìného komunálního odpadu. Pøispìje to ke zlepšení stavu

životního prostøedí nás všech. (Pouze pro Evropskou unii)

Polski

To urz¹dzenie oznakowane jest specjalnym symbolem odzysku. Pookresie

u¿ytkowania trzeba je zwrócic do odpowiedniego punktu zbiörki i nie wolno

umiestczaæ go razem z nieposortowanymi odpadami. Takie dzialanie przyniese

korzyœæ dla œrodowiska. (Tylko w Unii Europejskiej)

Lietuviu

Šis gaminys yra pažymetas specialiu atlieku tvarkymo ženklu. Baigus

eksploatacij¹, gaminys turi buti atiduotas i atitinkam¹ surinkimo punkt¹ ir negali

buti šalinamas kartu su nerušiuojamomis atliekomis. Tokie Jusu veiksmai prisides

prie aplinkos apsaugos. (Tiktai Europos S¹jungoje)

European Union Only

WEEE

Page is loading ...

iTEC U3METALDOCK User guide

Brand: iTEC

Model: U3METALDOCK

Category: Notebook docks & port replicators

Type: User guide

Download PDF

report

in other languages

Deutsch: iTEC U3METALDOCK Benutzerhandbuch
slovenčina: iTEC U3METALDOCK Užívateľská príručka
polski: iTEC U3METALDOCK instrukcja
čeština: iTEC U3METALDOCK Uživatelská příručka

iTEC U3METALDOCK User guide

iTEC U3METALDOCK User guide

in other languages

Related papers

Other documents