Rubbermaid 1784462 Operating instructions

Category
Flat panel wall mounts
Type
Operating instructions

Rubbermaid 1784462

The Rubbermaid 1784462 is a vertical ball rack designed to store and organize sports balls. It can be mounted on a FastTrack® rail or directly to wall studs, making it a versatile storage solution for any home or garage. With its durable construction and adjustable design, the Rubbermaid 1784462 can accommodate a variety of ball sizes and types, including basketballs, footballs, soccer balls, and volleyballs. The rack features multiple bands to securely hold the balls in place, and the side panels help to prevent the balls from rolling off.

Rubbermaid 1784462

The Rubbermaid 1784462 is a vertical ball rack designed to store and organize sports balls. It can be mounted on a FastTrack® rail or directly to wall studs, making it a versatile storage solution for any home or garage. With its durable construction and adjustable design, the Rubbermaid 1784462 can accommodate a variety of ball sizes and types, including basketballs, footballs, soccer balls, and volleyballs. The rack features multiple bands to securely hold the balls in place, and the side panels help to prevent the balls from rolling off.

A. Ensamble la pinza en el anillo superior. Asegúrese que el
reverso de la pinza mira hacia afuera del anillo.
B. Alinee los recortes en el alambre con la ranura de la pinza.
B1. Inserte la llave en la pinza.
B2. Golpee uniformemente el saliente con un martillo hasta
que esté a ras con el reverso de la pinza.
C. Ensamble los 3 paneles laterales al anillo inferior usando
los tornillos provistos.
(Nota: asegúrese que el soporte central
del panel lateral con el agujero sea el que esmás cerca al anillo
inferior).
C1. Ensamble el anillo superior a los 3 paneles laterales
(Nota: asegúrese de mantener los soportes de las bandas hacia el
frente del estante para pelotas tanto en el anillo superior como en
el inferior).
D. Ensamble las bandas en los soportes de bandas en los
anillos superior e inferior como se muestra.
PARTS INCLUDED | Componentes Incluídos
B2
B1B
L8-5E16-P0
Graphics Date: 11/17/04 Version: 1
File Name: 04-870-GO / 5E16Instructions Designer: Adam Chumita
Size: 8.5" x 11"
COLORS:
Use PANTONE MATCHING SYSTEM for an accurate color representation
JOB NO. 04-870-GO Reader
A. Assemble gripper onto top ring. Make sure to face
back of gripper towards the outside of the ring.
B. Align cut outs in wire with gripper slot.
B1. Insert key into gripper.
B2. Use a hammer and tap slug in evenly until it
appears flush with back of gripper.
C. Assemble 3 side panels using the provided screws
to the bottom ring.
(Note: make sure the side panel’s center support with hole is closest
to the bottom ring.)
C1.Assemble top ring to all three side panels.
(Note: make sure to keep band holders towards the front of the ball
rack on both top and bottom rings.)
D. Assemble bands into the band holders on top and
bottom rings as shown.
A
D
C1
C
E. Attach Ball Rack to FastTrack® Rail.
F. Level the Ball Rack and mark the hole in center support
of side panel.
G. If the rack is not on a stud, drill a 3/8" hole and insert a
wall anchor.
H. Secure screw in center support of side panel.
E. Fije el estante para pelotas al riel FastTrack®.
F. Nivele el estante para pelotas y marque el agujero en el
soporte central del panel lateral.
G. Si el estante no está en un montante, perfore un agujero
de 3/8”e inserte un anclaje para pared.
H. Asegure el tornillo en el soporte central del panel lateral.
Back of Gripper
Reverso de
pinza
5E33 Gripper 1
5E33 Pinzas 1
5E33 Gripper Key 1
5E33 Llave de pinzas 1
10707-50 Top Ring 1
10707-50 Anillo superior 1
10707-49 Bottom Ring 1
10707-49 Anillo inferior 1
10707-48 Side Panels 3
10707-48 Paneles laterales 3
5E34 Bands 2
5E34 Bandas 2
5E35 Screws 12
5E35 Tornillos 12
5E35 Screws: If Direct Wall Mounted 3
5E35 Tornillos:
Si se montan directamente en la pared
3
5E35 Anchors and Anchor Key 1 | 1
5E35 Anclajes y Llave de anclaje 1 | 1
Ball Rack can be attached to FastTrack® rail or direct mounted
to wall studs.
El estante para pelotas puede fijarse al riel FastTrack® o
montarse directamente a los montantes de pared.
Wall Stud
Parante de
pared
E
F G H
VERTICAL BALL RACK
Estante Vertical para Pelotas
ASSEMBLING BALL RACK | Ensamble del estante para pelotas
1. Locate wall stud 1. Localice los montantes de la pared
2. Level item 2. Nivele el objeto
3. Mark mounting holes 3. Señale los agujeros de montaje
4. Pre-drill 1/8" holes 4. Empiece a taladrar agujeros de 1/8 pulg.
5. Secure item to stud 5. Sujete el objeto al montante
RAIL MOUNT | Montaje en el riel
REQUIRED TOOLS for Ball Rack Assembly
HERRAMIENTAS REQUERIDAS para ensamble
del estante vertical para pelotas
STUD FINDER
1/8"
REQUIRED TOOLS
Herramientas Requeridas
DIRECT WALL MOUNT (Option) | Montaje directamente en la pared (Opción)
Rubbermaid Home Products, Fairlawn, OH, U.S.A. 44333-3306 • 1-888-895-2110 • www.rubbermaid.com • Patent pending. Patente solicitada.
3/8"
  • Page 1 1

Rubbermaid 1784462 Operating instructions

Category
Flat panel wall mounts
Type
Operating instructions

Rubbermaid 1784462

The Rubbermaid 1784462 is a vertical ball rack designed to store and organize sports balls. It can be mounted on a FastTrack® rail or directly to wall studs, making it a versatile storage solution for any home or garage. With its durable construction and adjustable design, the Rubbermaid 1784462 can accommodate a variety of ball sizes and types, including basketballs, footballs, soccer balls, and volleyballs. The rack features multiple bands to securely hold the balls in place, and the side panels help to prevent the balls from rolling off.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages