Sea gull lighting 77270-839 Installation guide

77270-839
Sea gull lighting
Brand
Sea gull lighting
Model
77270-839
Category
Interface hubs
Type
Installation guide

Sea Gull Lighting 77270-839 is a 2-light semi-flush convertible pendant that can be used in dry locations and dimmed with a standard incandescent dimmer. It requires a qualified electrician for installation and has a one-year warranty. It uses a maximum 120-volt, 75-watt Type A19 medium base lamp. You can easily adjust the height of the fixture by removing a portion of the chain. Make sure to connect the black fixture wire to the hot power line wire and the white fixture wire to the neutral power line wire.

Sea Gull Lighting 77270-839 is a 2-light semi-flush convertible pendant that can be used in dry locations and dimmed with a standard incandescent dimmer. It requires a qualified electrician for installation and has a one-year warranty. It uses a maximum 120-volt, 75-watt Type A19 medium base lamp. You can easily adjust the height of the fixture by removing a portion of the chain. Make sure to connect the black fixture wire to the hot power line wire and the white fixture wire to the neutral power line wire.

Page is loading ...
1A
Install the Fixture
Use MAX 75 Watt120 volt
Type A19 Medium Base Lamp.
2
Using the thumb nuts, attach the fixture arms to the hub.
Unscrew the fixture loop from inside the hub and remove the thumb nut bolts by unscrewing the thumb
nuts.
Install the mounting plate with the two mounting studs to the electrical box with two mounting plate
screws.
Screw the shorter end of the threaded nipple tightly onto the mounting plate.
Secure the mounting plate to the electrical box with two mounting plate screws.
Screw the screw collar tightly onto the threaded nipple.
Screw the fixture loop onto the fixture.
Determine the wanted height of the fixture and remove a portion of the chain by opening a link and removing it from the bottom.
Install the canopy and the collar nut onto the chain (in that order) then install the open link onto the fixture loop and secure it in place by
closing the link.
Weave the cord through the chain, screw collar, canopy, threaded nipple, and out of the electrical box. Trim the cord leaving enough to make
electrical connections.
Connect the fixture to a suitable ground in accordance to local electrical codes.
Connect the white fixture wire (square and rigid tracer) to the neutral power line wire with a wire nut.
Connect the black fixture wire (round and smooth tracer) to the hot power line wire with a wire nut.
Align then place the canopy onto the mounting plate studs and secure it with the two thumb nuts.
Neatly place all the wires into the electrical box, place the canopy onto the ceiling, and secure it in place by screwing the collar nut tightly
onto the screw collar.
FOR SEMI-FLUSH MOUNT ONLY:
FOR SEMI-FLUSH MOUNT ONLY:
SKIP TO STEP 11
FOR SEMI-FLUSH MOUNT ONLY: SKIP TO
STEP 16
Screw the lamps in to the sockets.
Screw the bottom threaded nipple in the socket assembly, washer, shade washer, and the shade onto the nipple and secure them in place
with the nut.
Align the shade frame to the fixture arms, place the shade frame through the threaded nipple and secure it place with the finial and cap
nuts.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Semi-Flush Mounting
HUB
THUMB
NUT
BOLT
FIXTURE
LOOP
MOUNTING
PLATE
2
MOUNTING PLATE STUD
17
18
3
ELECTRICAL BOX
FIXTURE ARMS
MOUNTING PLATE
CANOPY
CHAIN
FIXTURE LOOP
THUMB NUT
HUB
BOTTOM NIPPLE
SHADE
CAP NUT
WASHER
SHADE WASHER
SHADE FRAME
FINIAL
LAMP
THREADED NIPPLE
SCREW COLLAR
MOUNTING PLATE SCREW
COLLAR NUT
5
1
NUT
THUMB NUT
1
6
7
9
9
16
17
17
18
18
18
18
SOCKET
ASSEMBLY
17
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Sea gull lighting 77270-839 Installation guide

77270-839
Sea gull lighting
Brand
Sea gull lighting
Model
77270-839
Category
Interface hubs
Type
Installation guide

Sea Gull Lighting 77270-839 is a 2-light semi-flush convertible pendant that can be used in dry locations and dimmed with a standard incandescent dimmer. It requires a qualified electrician for installation and has a one-year warranty. It uses a maximum 120-volt, 75-watt Type A19 medium base lamp. You can easily adjust the height of the fixture by removing a portion of the chain. Make sure to connect the black fixture wire to the hot power line wire and the white fixture wire to the neutral power line wire.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents