5-CD Shelf System |
Lecteur de CD de salon à 5 disques
|
Sistema de
audio tipo ejecutivo con 5 CD
NS-A1111
NS-A1111_final_translationDTP.fm Page 1 Friday, February 17, 2006 12:09 PM
NS-A1111_final_translationDTP.fm Page 2 Friday, February 17, 2006 12:09 PM
3
www.insignia-products.com
Insignia NS-A1111
5-CD Shelf System
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety information . . . . . . . . . . . . . . . . . . . . . . . . 3
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setting up your shelf system . . . . . . . . . . . . . . . . 6
Using your shelf system. . . . . . . . . . . . . . . . . . . . 7
Maintaining your shelf system . . . . . . . . . . . . . . 11
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Warranty information . . . . . . . . . . . . . . . . . . . . . 12
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Français. . . . . . . . . . . . . . . . . . . . . . . . 14
Español . . . . . . . . . . . . . . . . . . . . . . . . 26
Introduction
Congratulations on your purchase of a
high-quality Insignia product. Your NS-A1111
5-CD shelf system represents the state of the art
in stereos, designed for reliable and trouble-free
performance.
Safety information
I
I
Read instructions
Read all safety and operating instructions before
operating your shelf system.
Retain instructions
Keep the safety and operating instructions for
future reference.
Heed warnings
Follow to all warnings on your shelf system and
in the operating instructions.
Follow instructions
Follow all operating and use instructions.
Water and moisture
Do not use your shelf system near water. For
example, avoid using near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or
near a swimming pool.
Wall or ceiling mounting
Do not mount your shelf system to a wall or
ceiling.
Accessories
Use only attachments and accessories
specified. Use the shelf system only with a cart,
stand, tripod, bracket, or table specified by
Insignia or sold with the shelf system. When
using a cart, use caution when moving the cart
and shelf system combination to avoid injury
from it tipping over.
Ventilation
Slots and openings in the cabinet back or bottom
are provided for ventilation, to ensure reliable
operation of your shelf system, and to protect it
from overheating. These openings must not be
blocked or covered. Do not place the unit on a
bed, sofa, rug, or other similar surface. Do not
place the unit near or over a radiator or heat
source. Do not place your shelf system in a
built-in installation such as a bookcase or rack
unless you provide correct ventilation or follow
the manufacturer's instructions.
Power source
Operate your shelf system only from the type of
power source indicated on the rating plate
(located on the back of the shelf system).
If you are not sure of the type of power supply to
your home, consult your shelf system dealer or
local power company.
Grounding and polarization
Your shelf system is equipped with a polarized
alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug
still won’t fit, contact your electrician to replace
your obsolete outlet.
Instead of the polarized alternating-current line
plug, your shelf system may be equipped with a
3-wire grounding-type plug (a plug having a third
(grounding) pin). This plug will only fit into a
grounding-type power outlet. This, too, is a
safety feature. If you are unable to insert the plug
into the outlet, contact your electrician to replace
your obsolete outlet. Do not defeat the safety
purpose of the grounding-type plug.
Power cord protection
Route power supply cords so they are not likely
to be walked on or pinched by items placed on or
against them. Pay particular attention to cords at
plugs, power outlets, and the point where they
exit from your shelf system.
Headphones
When you use headphones, keep the volume at
a moderate level. Using headphones
continuously at high volume may cause hearing
damage.
Lightning
To protect your shelf system from a lightning
storm, or when it is left unattended and unused
for long periods of time, unplug it from the power
outlet and disconnect the antenna or cable
system. This will prevent damage to your shelf
system from lightning and power line surges.
Overloading
Do not overload power outlets and extension
cords because this can result in a risk of fire or
electric shock.
Warning
To reduce the risk of fire or electric shock, do not
expose your shelf system to rain or moisture.
Warning
To reduce the risk of electric shock, do not remove the
cover (or back). No user serviceable parts inside.
Refer servicing to qualified service personnel.
NS-A1111_final_translationDTP.fm Page 3 Friday, February 17, 2006 12:09 PM
4
Insignia NS-A1111 5-CD Shelf System
www.insignia-products.com
Object and liquid entry
Do not push objects through any openings in
your shelf system because they may touch
dangerous voltage points or short out parts that
could result in fire or electric shock. Never spill or
spray any type of liquid into your shelf system.
Damage requiring service
Do not try to service your shelf system yourself.
Opening or removing covers may expose you to
dangerous voltage or other hazards. Unplug
your shelf system from the power outlet and
refer servicing to qualified service personnel
under the following conditions:
• When the power supply cord or plug is
damaged.
• If liquid has been spilled, or objects have
fallen, into your shelf system.
• If your shelf system has been exposed to rain
or water.
• If your shelf system does not operate
normally by following the operating
instructions. Adjust only those controls that
are covered by the operating instructions
because an incorrect adjustment of other
controls may result in damage and will often
require extensive work by a qualified
technician to restore your shelf system to its
normal operation.
• If your shelf system has been dropped or the
cabinet has been damaged.
• If your shelf system exhibits a distinct change
in performance.
Replacement parts
When replacement parts are required, make
sure that the service technician uses
replacement parts specified by Insignia or those
that have the same characteristics as the
original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
Safety check
Upon completion of any service or repairs to
your shelf system, ask the service technician to
perform safety checks to determine that your
shelf system is in correct operating condition.
Heat
Locate your shelf system away from heat
sources such as radiators, heat registers,
stoves, or other products (including amplifiers)
that produce heat.
Disc slot
Keep your fingers clear of the disc slot as it is
closing. You may injure yourself.
Disc
Do not use a cracked, deformed, or repaired
disc. These discs are easily broken and may
cause serious personal injury and product
malfunction.
Equipment classification
This is classified as Class II equipment, which
means that the shelf system has a
double-insulation system.
F
Invisible laser
radiation
possible when
open and
interlock failed or
defeated. Avoid
direct exposure
to laser beam.
Laser safety
This shelf system employs an optical
laser beam system in the CD
mechanism designed with built-in
safeguards. Do not try to disassemble.
Refer to qualified service personnel.
Exposure to this invisible laser light
beam may be harmful to the human
eye.
This is a Class-1 laser product. Using
controls, adjustments, or procedures
other than those specified herein may
result in hazardous laser light beam
exposure.
NS-A1111_final_translationDTP.fm Page 4 Friday, February 17, 2006 12:09 PM
5
Insignia NS-A1111 5-CD Shelf System
www.insignia-products.com
Features
Shelf system
Remote
CD door
Volume control
ON/OFF button
Headphone jack
Function button
Open and close button
TIMER button
Memory button
Stop button
Display window
Remote control sensor
Tuner control
Aux in indicator
Aux in jack
Band button
Disc skip button
Skip/search/preset button
Play/pause/clock set button
CD storage
Control Symbol Description
CD door Press to open and close to
load and unload discs.
Volume control Rotate to adjust the volume.
ON/OFF button Press to turn the shelf
system on and off. Also
places system in standby
mode.
Headphone jack Connects headphones with a
3.5 mm stereo mini plug to
the shelf system.
Function button Press to switch between CD,
tuner, and aux in.
Open and close button Press to open and close the
CD door.
TIMER button Press to set a timer alarm.
Memory button Press to program tracks for
storage in memory.
Stop button Press to stop playing a disc.
Display window Shows whether the shelf
system is on or off and
displays the time. Indicators
also show system settings.
Remote control sensor Receives the remote control
signal.
Tuner control Rotate to adjust the radio
frequency.
Aux in indicator Lights when an external
(auxiliary) audio source is
plugged in.
Aux in jack Connects external (auxiliary)
audio sources.
Band button Press to switch between AM
and FM radio bands.
Disc skip button Press to skip playing an
entire disc loaded in the CD
changer.
Skip/search/preset
button
Press to skip or search for a
CD track, or to recall a track
stored in memory.
Play, pause, and clock
set button
Press to start, pause or
resume playing a disc.
Also sets the time on the
clock.
CD storage Stores CDs when not in the
CD changer.
Control Symbol Description
Standby/On button Press to turn the shelf
system on and off. Also
places system in standby
mode.
Stop button Press to stop playing a disc.
Skip backward/preset-
button
Press to skip a CD track or to
recall a track stored in
memory.
Memory button Press to program tracks for
storage in memory.
Control Symbol Description
/
Stop button
Standby/On button
Skip/preset- button
Memory button
Tuning (down)
button
TIMER button
Volume +/-
button
Disc skip button
FUNCTION button
Tuning (up)
button
Play/pause button
Skip/preset+ button
Repeat button
BAND button
NS-A1111_final_translationDTP.fm Page 5 Friday, February 17, 2006 12:09 PM
6
Insignia NS-A1111 5-CD Shelf System
www.insignia-products.com
Display
Setting up your shelf
system
Preparing the remote control
Installing remote control batteries
I
I
To install batteries in the remote control:
1 Remove the battery cover.
2 Insert one CR2025 (3-volt) battery into the
battery compartment. Make sure that the +/–
symbols on the battery match the +/– marks
inside the battery compartment.
3 Replace the battery cover.
4 Remove the plastic tab covering the remote
control sensor.
5 Point the remote control at the remote sensor
on the shelf system. The effective distance
for remote operation is about 16 feet (5
meters).
Tuning (down) button Press to adjust radio setting
from a higher to lower
frequency.
TIMER button Press to set a timer alarm.
Volume +/- buttons Press to adjust the volume.
Disc skip button Press to skip playing an
entire disc loaded in the CD
changer.
Tuning (up) button Press to adjust radio setting
from a lower to higher
frequency.
Play/pause button Press to start or resume
playing a disc.
Press to pause playback of
disc.
Skip forward/preset+
button
Press to start, pause, or
resume playing a disc.
Repeat button Press to replay a track.
Band button Press to switch between AM
and FM radio bands
Function button Press to switch between CD,
tuner, and aux in.
Indicator Description
Band Displays FM or AM radio band.
Clock AM/PM Indicates that the time is AM or PM.
Clock/CD track/
broadcast station
• In clock mode, displays the time.
• In CD mode, displays the track
number.
• In broadcast station mode,
displays the station number.
MEMORY Displays when the track being played is
stored in memory.
STEREO Indicates that the FM signal is playing in
stereo.
REPEAT mode Displays when the repeat feature is in
use.
Radio frequency Shows whether the radio frequency is
megahertz or kilohertz.
Control Symbol Description
Band
Clock
AM/PM
Clock/CD
track/
broadcast
station
STEREO
Repeat
mode
Radio
frequency
MEMORY
Warning
Do not throw the batteries into fire. Dispose of used
batteries as hazardous waste.
Caution
Do not drop or disassemble the remote control. Do not
get the remote control wet.
Note
When using the remote control and you are
required to move closer to the stereo for the
remote control to operate, replace the battery. The
remote control may not operate correctly if direct
sunlight or the light of a high-frequency fluorescent
lamp enters the remote control light sensor. In this
case, change the system installation position to
prevent the problem.
Note
When the remote control will not be used for a long
period of time or when the batteries are worn out,
remove the batteries to prevent leakage.
NS-A1111_final_translationDTP.fm Page 6 Friday, February 17, 2006 12:09 PM
7
Insignia NS-A1111 5-CD Shelf System
www.insignia-products.com
Connecting speakers to the shelf system
To connect the speakers:
1 Position the speakers supplied with the shelf
system to the right and left of the shelf
system.
2 Connect the wires from the speakers to the
amplifier speaker connectors.
Connecting power to the shelf system
To connect the power cord:
1 Make sure that the speakers are properly
connected and that the ON/OFF button is set
to OFF.
2 Connect the AC power cord to an AC outlet.
Connecting the antenna
To connect the antenna:
1 Fully unwind the FM wire antenna. Extend
the antenna and move it to determine the
best sound reception.
2 Connect the provided AM loop antenna to the
AM LOOP ANTENNA snap terminals on the
back of the shelf system, then move it to
determine the best sound reception.
Connecting external equipment
You can connect external audio systems to the
shelf system.
To connect external equipment:
1 Make sure that the power on the shelf system
is off.
2 Plug the jack from the external equipment
into the aux in jack (with the music note
symbol) on the front panel.
Connecting headphones
To connect the headphones:
1 Turn down the volume on the shelf system.
2 Plug headphones with a 3.5 mm stereo mini
plug into the headphone jack.
Using your shelf system
Turning the shelf system on and off
The display changes according to the button
pressed or feature selected.
To turn the shelf system on and off:
1 When the shelf system is off, press the ON/
OFF button on the shelf system once to turn
it on. The display shows d1 and turns on the
display backlight.
2 When the shelf system is on, press the ON/
OFF button on the shelf system once to turn
it off. The display backlight goes out.
When the shelf system is turned off, the clock
still shows on the display without a backlight.
This is called the standby mode.
Listening to external equipment
To listen to external equipment:
1 Press the ON/OFF button on the shelf
system once to turn it on.
2 Press the Function button on the front panel
to Aux, indicated by a music note symbol on
the display.
3 Turn on the external equipment.
Caution
Connecting speakers other than the speakers
provided with the shelf system may damage the
shelf system.
Note
Before operating the shelf system in a new area for the
first time, you must check that the operating voltage of
your shelf system is identical to the voltage of your
local power supply. This shelf system is to be operated
only at the power source voltage printed on the back
panel. Disconnect from the power outlet when not in
use for a long period of time.
Note
Do not connect the shelf system’s FM antenna to
an outside antenna.
AC power
cord
Amplifier
speaker
conectors
Left
speaker
box
Right
speaker
box
Note
When the headphones are connected, the
speakers on the shelf system are automatically
disabled.
Note
Disconnect the power cord when the unit is not
going to be used for a long time.
Note
If the external equipment is a television and this
shelf system is close to the TV, you may
experience interference if the tuner function is
selected while the TV is on.
NS-A1111_final_translationDTP.fm Page 7 Friday, February 17, 2006 12:09 PM
8
Insignia NS-A1111 5-CD Shelf System
www.insignia-products.com
Adjusting the sound
To adjust the sound:
1 Turn the volume control knob to obtain the
desired volume level.
2 For personal listening, connect headphones
to the shelf system.
Setting the clock
To set the clock:
1 When the shelf system is on, press the ON/
OFF button on the shelf system to turn off the
shelf system and enter the standby mode.
The clock will show on the display without a
backlight.
2 Press the PLAY/PAUSE button until the hour
flashes on the display, then press the search/
skip button repeatedly to set the current hour.
3 Press the PLAY/PAUSE button until the
minute flashes on the display, then press the
search/skip button repeatedly to set the
current minute.
4 Press the PLAY/PAUSE button until 12H or
24H flashes on the display, then press the
search/skip button to select either a 12-hour
or 24-hour time format.
5 Press the PLAY/PAUSE button to confirm the
time setting.
Setting the timer alarm
To set the timer alarm:
1 When the shelf system is on, press the ON/
OFF button on the shelf system to turn off the
shelf system and enter the standby mode.
The clock will show on the display without a
backlight.
2 Press the TIMER button once.
3 Press the PLAY/PAUSE button until the hour
flashes on the display, then press the search/
skip button repeatedly to set the desired
hour.
4 Press the PLAY/PAUSE button until the
minute flashes on the display, then press the
search/skip button repeatedly to set the
desired minute.
5 Press the PLAY/PAUSE button to confirm the
time setting. An alarm sounds when the time
reaches the preset time.
6 Press the TIMER button a second time to
cancel the alarm after setting the timer alarm.
Tuning the radio
Manual tuning
To manually tune the radio:
1 Press the ON/OFF button on the shelf
system once to turn it on.
2 Press the FUNCTION button to tuner mode,
which is shown by the radio frequency
indicator on the display.
3 Press the BAND button to select the band
(AM or FM), which is shown by the band
indicator on the display, then tune a station.
4 To search for a station quickly, hold the tuning
(up) or tuning (down) button on the remote
control. Station searching starts
automatically and stops automatically when a
station is found.
Note
When the headphones are connected, the
speakers on the shelf system are automatically
disabled.
/
/
/
/
Note
Make sure that the time setting is correct before
setting the timer alarm.
Note
In FM mode, the stereo indicator lights when
reception is good.
Note
After changing the band or turning the radio off and
on again, the last station selected will be recalled.
/
/
/
FUNCTIO
N
FUNCTIO
N
FUNCTIO
N
FUNCTIO
N
NS-A1111_final_translationDTP.fm Page 8 Friday, February 17, 2006 12:09 PM
9
Insignia NS-A1111 5-CD Shelf System
www.insignia-products.com
Preset tuning
The system stores a total of 40 stations. (Each
band has a maximum of 20 available preset
stations.) Presetting allows you to tune into a
station directly. Stations are assigned preset
numbers, beginning from 1 in consecutive order
for each band (AM and FM).
To program preset radio stations:
1 Manually select a radio station (see page 8).
2 Press the memory button to store the station
in memory.
3 Repeat steps 1 and 2 to preset up to 20 AM
and 20 FM stations.
Recalling a preset station
To recall a preset radio station:
1 Press the ON/OFF button on the shelf
system once to turn it on.
2 Press the FUNCTION button to tuner mode,
which is shown by the radio frequency
indicator on the display.
3 Press the BAND button to select the band
(AM or FM), which is shown by the band
indicator on the display, then tune a station.
4 Press the skip/search/preset button until the
desired number for the preset station shows
on the display.
Using the CD changer
Loading CDs
To load CDs in the changer:
1 Press the ON/OFF button on the shelf
system once to turn it on.
2 Press the FUNCTION button to CD mode,
which is shown on the display.
3 Press the open/close button to open the disc
tray.
4 Load the first disc into the disc tray, label side
up.
5 Press the disc skip button to revolve the disc
tray clockwise. Repeat to load up to five discs
in the CD changer.
6 Press the open/close button to close the disc
tray. There will be a slight delay while the CD
changer checks the discs.
Playing CDs
To play CDs:
1 Press the disc skip button to select the
desired disc, then press either of the skip/
search/preset buttons to select a track on the
selected disc. The selected disc flashes on
the display.
2 Press the PLAY/PAUSE button to start
playback. Press during play to pause play,
then press again to resume playing.
Note
In FM mode, the stereo indicator lights when
reception is good.
Note
After changing the band or turning the radio off and
on again, the last station selected is recalled.
Note
The memory entry (channel number, frequency
band, and frequency) that have been stored
appear on the display in numerical order,
regardless of the frequency band.
FUNCTIO
N
FUNCTIO
N
FUNCTIO
N
FUNCTIO
N
Note
The disc tray can be opened during playback to
change or add a disc not in play. While the tray is
open, the selected disc will not stop playing, but
the disc skip button will not work to select another
disc.
NS-A1111_final_translationDTP.fm Page 9 Friday, February 17, 2006 12:09 PM
10
Insignia NS-A1111 5-CD Shelf System
www.insignia-products.com
3 Press the stop button to stop playback.
Locating tracks
To skip to a track in sequence:
1 To go to the beginning of the current or the
preceding track, press the skip/search/preset
reverse button once.
2 To go to the beginning of the next track on the
CD, press the skip/search/preset forward
button once.
To search for a point in a track:
1 Press and hold the skip/search/preset
reverse button to move backward at high
speed. Release the button at the desired
point.
2 Press and hold the skip/search/preset
forward button to move forward at high
speed. Release the button at the desired
point.
Repeating a track or disc
Repeat playback allows you to repeat the current
track, an entire disc, or all discs in the CD
changer.
You can use repeat playback during normal
playback (playback mode), stop mode, or pause
mode.
To repeat play during playback mode:
1 To repeat a track that is playing, press
Repeat on the remote control until the
display shows REPEAT and r1 (indicating a
track repeat). The currently playing track will
play repeatedly until you press the STOP
button.
2 To repeat the entire disc that is playing, press
Repeat on the remote control until the
display shows REPEAT and rd (indicating a
disc repeat). The currently playing disc will
play repeatedly from the current playing
point.
3 To repeat all discs in the CD changer, press
Repeat on the remote control until the
display shows REPEAT and rA (indicating a
all-disc repeat). The discs will play repeatedly
from the current playing point.
4 Press the search/skip buttons to use select
another track on the selected disc, or use the
disc skip button to play the first track of the
newly selected disc.
5 To cancel repeat play, press Repeat on the
remote control until REPEAT disappears
from the display.
To repeat play during stop or pause modes:
1 While the CD player is stopped or paused,
program the repeat play function as if the CD
were in playback mode.
2 From stop mode, press the PLAY/PAUSE
button to begin repeat play. The currently
playing disc will play from the beginning of
the first track.
3 From pause mode, press the PLAY/PAUSE
button to begin repeat play. The currently
playing disc will play from the point at which
play was paused.
Programming CD tracks
The system stores a total of 20 tracks from all
available discs in the disc tray. These tracks can
be played in a preset order.
Note
Before transporting the unit, remove any disc from
the disc compartment.
Note
Searching and skipping can be done during playback
or pause, but can only be done for the CD currently
playing.
Note
The skip/search buttons can be used during this
function and operate normally.
Reverse skip
Forward skip
Reverse search Forward search
Note
The skip/search buttons can be used during this
function but operate in the search mode only.
NS-A1111_final_translationDTP.fm Page 10 Friday, February 17, 2006 12:09 PM
11
Insignia NS-A1111 5-CD Shelf System
www.insignia-products.com
To program CD playback:
1 With the CD player in stop mode, press the M
(memory) button. P:00 shows on the display
indicating that no tracks have been
programmed.
2 Press the search/skip button to select the
desired disc. The disc number shows in the
display.
3 Press the search/skip button again to select
the desired track. The track number shows
after the disc number in the display.
4 Press the M (memory) button again to store
the disc and track in memory.
5 Repeat steps 2 through 4 to program up to 19
additional tracks in memory.
6 To check the program, press the PLAY/
PAUSE button to start play, then press a
search/skip button to make sure that the next
programmed track plays.
To erase a CD program:
1 Press the stop button until MEMORY
disappears from the display. The display
shows the information for the current disc in
the CD changer.
OR
2 Open the disc tray by pressing the OPEN/
CLOSE button.
OR
3 Press FUNCTION to select another function.
Playing programmed tracks
1 Press the PLAY/PAUSE button to start
playback. Press during play to pause play,
then press again to resume playing.
2 Press a search/skip button to move to
another programmed track.
Maintaining your shelf
system
Cleaning the player
• Wipe with a soft cloth. If the player is very
dirty, dampen the cloth with a weak solution
of neutral detergent and water, and then wipe
clean. Do not use compressed air to remove
dust.
Caring for CDs
• Do not touch the surface of the unlabeled
side of the disc.
• Do not attach paper or tape to the surface of
the disc.
• Do not expose the disc to direct sunlight or
excessive heat.
• Do not use irregularly shaped discs (for
example: heart shaped or octagonal discs).
They may cause malfunctions.
Note
The same track can be selected more than once in the
same program. (For example, you could set a program
to play the same track 20 times.)
Note
While playing programmed tracks, the search/skip
button can only be used to select tracks that have
been programmed.
Note
While playing programmed tracks, repeat play will not
work for all discs.
Note
The memory entry (disc and track) that have been
stored appear on the display in numerical order.
FUNCTIO
N
FUNCTIO
N
FUNCTIO
N
FUNCTIO
N
NS-A1111_final_translationDTP.fm Page 11 Friday, February 17, 2006 12:09 PM
12
Insignia NS-A1111 5-CD Shelf System
www.insignia-products.com
Cleaning CDs
A dirty disc causes sound skipping, and if the
disc is very dirty, the CD may not work at all.
Handle the disc by holding its inner and outer
edges.
• Fingerprints and dust should be carefully
wiped from the surface of the CD with a soft
cloth. Wipe in a straight motion from the
center to the edge.
• Never use thinner, benzine, record cleaner,
or anti-static spray on a CD, because they
can damage its plastic surface.
Troubleshooting
Specifications
Design and specifications are subject to change
without notice.
FCC compliance
This equipment has been tested and found to
comply within the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced
technician for help.
Safety certification
This shelf system is made and tested to meet
safety standards of the FCC, requirements and
compliance with safety performance of the U.S.
Department of Health and Human Services, and
also with FDA Radiation Performance Standards
21 CFR Subchapter J.
Warranty information
Limited warranty
Insignia Products warrants to you, the original
purchaser of this Product, that this product shall
be free of defects in material or workmanship for
a period of ninety (90) days from the date of
purchase as follows:
1 LABOR: During the Warranty Period if this
Product is determined to be defective,
Insignia will repair or replace the Product, at
its option at no charge, or pay the labor
charges to any Insignia authorized service
facility. After the Warranty Period, you must
pay for all labor charges.
Note
Before transporting the unit, remove any disc from
the disc compartment.
Problem Solution
No sound. • Turn the volume knob up.
• The headphones are connected.
Disconnect them.
• Reset the unit by pressing the ON/OFF
button.
No or
unbalanced
sound from a
speaker.
Check the speaker connections of the
inoperative speaker.
Reversed left
and right
sound.
Check the speaker cord connection and
speaker location.
Severe hum or
noise.
• A TV or VCR is too close to the shelf
system. Separate the shelf system
from the TV or VCR.
• The plugs and jacks are dirty. Wipe
them with a cloth slightly moistened
with alcohol.
• Clean the disc.
• Adjust the antenna wire.
The FM stereo
indicator
flashes.
Reception is poor. Adjust the antenna wire.
CD door does
not close due to
power off or
other functions
are selected
without first
closing the
door
• Press the ON/OFF button to turn on
the shelf system.
•Press the Function button to select CD
mode.
• Press the Open/Close button to close
the CD door.
The disc does
not play
• The disc is not inserted correctly or is
upside down. Insert the disc correctly.
• Clean the disc.
• The CD system is in the pause mode.
Press the Play button to leave pause
mode.
Distorted
playback or
sound loss
during CD
playback
• Condensation may have formed inside
the unit because of a sudden change
in temperature. Wait about an hour for
the condensation to evaporate and try
again.
• CD disc is dirty or scratched. Clean
the disc.
Power sources
Power supply 120 V AC
60 Hz
Remote control
batteries
3V (1)
Power
consumption
15 W
NS-A1111_final_translationDTP.fm Page 12 Friday, February 17, 2006 12:09 PM
13
Insignia NS-A1111 5-CD Shelf System
www.insignia-products.com
2 PARTS: In addition, Insignia will supply, at no
charge, new or rebuilt replacement parts in
exchange for defective parts for the Warranty
Period. After the Warranty Period, you must
pay all parts costs.
To obtain warranty service, you must take the
Product with your original receipt or other proof
of purchase, either in its original packaging or
packaging affording an equal degree of
protection, to your nearest retail store location of
the store or online web site from which you
purchased the Product.
This warranty does not cover cosmetic damage
or damage due to acts of God, lightning strikes,
accident, misuse, abuse, negligence,
commercial use, or modification of, or to any part
of the Product, including the antenna. This
warranty does not cover damage due to
improper operation or maintenance, connection
to improper voltage supply, or attempted repair
by anyone other than a facility authorized by
Insignia to service the Product. This warranty
does not cover Products sold AS IS or WITH
ALL FAULTS, or consumables (such as fuses or
batteries). This warranty is valid only in the
United States and Canada.
This warranty is invalid if the factory applied
serial number has been altered or removed from
the Product.
REPAIR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER. INSIGNIA
SHALL NOT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY ON THIS PRODUCT.
EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY,
REPRESENTATION OR CONDITION OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT
IS LIMITED IN DURATION TO THE DURATION
OF THIS WARRANTY.
Some states or provinces do not allow the
exclusion or limitation of incidental or
consequential damages, or allow limitations on
how long an implied warranty lasts, so the above
limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and
you may have other rights which vary from state
to state, or province to province.
For customer service, please call
1-877-467-4289.
www.insignia-products.com
Insignia Products, Richfield, Minnesota, U.S.A.
Copyright
© 2006 Insignia. Insignia and the Insignia logo are
trademarks of Best Buy Enterprise Services, Inc. Other
brands and product names are trademarks or
registered trademarks of their respective holders.
Specifications and features are subject to change
without notice or obligation.
NS-A1111_final_translationDTP.fm Page 13 Friday, February 17, 2006 12:09 PM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
R1
NS-A1111_final_translationDTP.fm Page 38 Friday, February 17, 2006 12:09 PM
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Insignia NS-A1111 Manuel utilisateur
- español: Insignia NS-A1111 Manual de usuario
Related papers
-
Insignia NS-22 User manual
-
-
-
-
-
-
-
-
-