Atag MadQ Short Manual

Brand: Atag

Model: MadQ

Type: Short Manual

SHORT MANUAL

ATAG MadQ cascade-/mixed circuit control

unit

Operation and symbols General functions

Using the rotary pushbutton, selected setvalues and para-

meters can be selected, changed and, by subsequently pres-

sing the button, stored.

Turn to the right (+): increasing settings

Turn to the left (–): decreasing settings

Press once: Accept the selected value, store

Press long

: Entry into the programming level (level

selection)

3 sec

Standard display

Weekday, date, time heat

generator temperature

The line mark identifies the

active operating mode.

6633..55

1166::3322

FFRR 2266.. MMAARR..;;0044

°C

ÀÀ

6633..55

1166::3322

FFRR 2266.. MMAARR..;;0044

°C

Sunshade:

Summer shutdown active

(heating switched off, domestic

hot water according to program)

Ice crystal:

Frost protection for plant

active

ÁÁ

6633..55

1166::3322

FFRR 2266.. MMAARR..;;0044

°C

33 hh ss mm uu

Special display symbols

5500--44

EERRRROORR

DDHHWW

Alarm message (e.g. domestic hot

water)

appears alternately with the stan-

dard display - notify

heating specialist!

33 hh ss mm uu

For detailed information see manual Part Temperature set-

tings.

Heating curves (heating characteristics)

The heating curves adapt the heating performance, depen-

ding on the respective outside temperature, to the state of

the building.

The following settings should be selected as a base value:

The coldest outside temperature that can be expected forms

the basis of the calculation of the heat demand. The heating

specialist can inform you of this.

Correcting the heating curve

For detailed information see manual Part Heating curve.

663300

DDAAYY

DDHHWW

°C

Setting range: 10 °C to DHW-Max-Temp.

Setting domestic hot water temperature

Note:

During separate operation (heating- and domestic hot water

programs individually operable), first select the associated

heating circuit and accept it by pressing the rotary pushbutton

before setting the day or night temperature.

Setting range: 5.0 to 30 °C

116600

RROOOOMM NNIIGGHHTT

°C

Setting night temperature

For detailed information see manual Part Temperature set-

tings.

Heatingsystem

-12 °C -15°C -18°C

Floor 1.10 1.00 0.90

Radiator 1.70 1.55 1.45

Convector 2.20 2.00 1.85

Temperature

change

Accept change

Temperature

change

coldest outside temperature (regional)

Heating

circuit

select

11..5500

HHCC

HHEEAATT.. CCUURRVVEE

Accept heating circuit

11..5500

HHCC

HHEEAATT.. CCUURRVVEE

Room temperature too warm: reduce

Room temperature too cold: increase

Heating curve

change

Accept change

Quit (return to standard display)

If necessary, access the next circuit and correct the slope of the

heating characteristics.

Important! Only make corrections after 1-2 days and then

only in small steps. Almost completely open the

thermostatic valves of the radiators, if present!

Accept change

= Unmixed circuit

MC-1

= Mixed circuit 1

MC-2=Mixed circuit 2

Art.no. 8A521300 / 06.04

Subject to changes

Operating instruments of the control unit

1 – Rotary pushbutton

2 – Set day temperature

3 – Set night temperature

4 – Setting domestic hot water temperature

5 – Program selection button

6 – Key for heating curve adjustment

7 – Information button

8 – Key for emission measurement and manual operation

(only heating specialist)

9 – Display

10 – Compartment for short manual

Setting range: 5.0 to 30 °C

221100

RROOOOMM DDAAYY

°C

Setting day temperature

Accept change

For detailed information see manual Part Temperature set-

tings.

Temperature

change

FR.

12:42

26 . MAR

;;

57.5

8B521300_GB.qxd 16.07.2004 08:49 Seite 1

Programming timeprograms

The programming of timeprograms is carried out according to the following schematic. For detailed information, see

manual Part Programming of timeprograms. Each flashing adjustment value in the display can be corrected by

means of the rotary pushbutton and accepted by pressing the button again. Return to the previous step is accomplished

with button

¤¤

, return to the standard display by means of button

¢¢

or automatically after approx. 60 seconds.

The following programs may be selected:

1. Temporary programs:

HOLIDAY frost protected shutdown of heating and

domestic hot water during holiday period

ABSENT temporary interruption of heating period

during absence

PARTY temporary extension of heating period after

the set time block of the timeprogram has expi-

red

2. Automatic programs:

AUTOMATICAutomatic heating (day) and reducing

(night) according to timer program

SUMMER Exclusively domestic hot water according to

timer program, heating shut down, frost

protected

3. Permanent programs:

HEATING Permanent heating without time limitation

RED. HEATING Permanent reduced heating without time limi-

tation

STANDBY Frost protected shutdown of heating and

domestic hot water.

Select operating mode:

After pressing the

¢¢

button, the currently active program is

indicated by flashing. All other programs can be selected and

activated using the rotary pushbutton, whereby the arrowmark is

pointing towards the associated symbol.

Note: During separate operation, before selecting the

desired operating mode, first select and accept the

affected heating circuit.

Example: Selecting and activating automatic program

In the temporary programs, the associated times such as return

date (HOLIDAY), return time (ABSENT)

Programs

( )

33 hh ss mm uu

AAUUTTOOMMAATTIICC



33 hh ss mm uu

activate

For detailed information, see manual Part Operational mode

selection for heating and hot water, Functions of operational

modes as well as Quick operational mode selection.

or extended heating period (PARTY) can be set.

Example: Setting and activating holiday program

forward

TTIIMMEEPPRROOGGRRAAMMSS

HHCC

TTIIMMEEPPRROOGGRRAAMMSS

2211..00

MMOO--11

0066 ..0000--0088..0000

PP22

PPRROOGGRRAAMM

1. Select heating or domestic hot water circuit

Setting range: Unmixed circuit (HC), mixed circuit 1 (MC-1)*,

mixed circuit 2 (MC-2)*, domestic hot water circuit (DHW)

2. select timeprogram

only appears when enabled (see SYSTEM-parameter/par. timeprogram = P1-P3)

Setting range: P1, P2, P3

3. Select weekday and heating cycle

Setting sequence: Mo 1st cycle - Mo 2nd cycle, Tu 1st cycle - Tu 2nd cycle ... Su 2nd cycle,

Note: If the second cycle is in use, a third cycle is available.

4. Set heating start (

= 1st switching-on time)

Setting range: 0.00 to 24.00 h

Note: The switching-on time appears in the top time bar as a flashing segment.

HHCC

246

18 2220

2211..00

MMOO--11

0066 ..0000--0088..0000

246

18 2220

81416

forward

Entry into the level selection: Press rotary pushbutton for approx. 3 seconds

3 sec

Entry into the time program level

2211..00

MMOO--11

0066 ..0000--0088..0000

7. Select next weekday or next heating cycle

as described in 3.) and program accordingly.

246

18 2220

81416

5. Set heating end ( = 1st switching-off time)

Setting range: 0.00 to 24.00 h

Note: The switching-off time appears in the top time bar as a flashing segment

2211..00

MMOO--11

0066 ..0000--0088..0000

246

18 2220

81416

6. Set cycle temperatures ( = temperature during heating operation)

Setting range for heating circuits (HC, MC-1, MC-2): 5.0 to 30 °C

for the domestic hot water circuit (DHW): 10.0 to DHW maximum limit

Important: When changing the required daytime temperature or domestic hot water tem-

perature using the key

¥¥

§§

, all corresponding

cycle temperatures shift by the value of the change!

2211..00

MMOO--11

0066 ..0000--0088..0000

246

18 2220

81416

°C

forward

Accessing timeprogram level

Automatic

adjust

currently active

program

* if present

2277..0088

HHOOLLIIDDAAYY TTIILL



33 hh ss mm uu

2277..0088

HHOOLLIIDDAAYY TTIILL



33 hh ss mm uu

Holiday

select

Return

adjust

activate

currently active mode

Plant information

After pressing the information button, using the rotary pushbut-

ton, all plant temperatures as well as opertaional modes of all

plant components can be accessed one by one.

Turn clockwise:

– Plant temperatures (setvalues and

actual values)

– Function and values of variable inputs

– Counter and consumption data

Turn anti-clockwise:

Heating circuit information such as

– Operational mode (holiday, absent, party, auto,

summer etc.)

– Current timer program (P1 or P1-P3 after release)

– OPerational mode (daytime mode, reduced mode, ECO mode)

– Heating circuit (HC, MC-1, MC-2, DHW according to

device type)

– Status of the corresponding heating circuit pump (OFF-ON)

– Status of the corresponding mixing valve (OFF-STOP-CLOS)

– Status of the boiler control unit (OFF-ON)

– Status and function of the variable outputs

Note: The plant information only appears if the corresponding

functions are present in the device type.

For detailed information see manual Part Plant information.

°C

Art. 0451003406 - 0426-20

8B521300_GB.qxd 16.07.2004 08:49 Seite 2

Atag MadQ Short Manual

Atag MadQ Short Manual

Related papers

Other documents