Revised 5/08
© 2008 AS America Inc.
❑
❑
• High-gloss acrylic-capped ABS with
berglass reinforcement
• Integral apron
• Integral three-sided, tiling/water
retention ange
• Integral lumbar support
• Pre-leveled tub bottom
❑
❑
• .25 hp, single-speed pump motor
• 6 whirlpool jets
– 4 adjustable jets
– 2 mini-jets in the lumbar area
• Deck mounted air on/off switch
• Removable access panel
59-7/8" x 30" x 5"
(52 x 762 x 38mm)
• 6030Y.BW Bath Wall Set
• 6030Y.BWT Bath Tile Wall Set
• Tub can also be installed without Acrylux
wall set
• UL 795 for Hydromassage Bathtubs
• ASME A2.9.7M for Whirlpool Appliances
• ANSI Z24. for Plastic Bathtubs
6030Y.02
6030Y.28
2
Revised 5/08
© 2008 AS America Inc.
GENERAL SPECIFICATIONS FOR 6030Y1 BATHING POOL
60 x 30 x 5 In. (524 x 762 x 38mm)
5 Lbs. (23 Kg.)
384 Lbs. (74 Kg.)
40 Gal. (5 L)
46 In. L (68mm L)
53 In. L (346mm L)
in (279mm L)
3 Lbs./Sq.Ft. (50 Kgs./Sq.m)
7.3
8.9ft
3
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
GENERAL SPECIFICATIONS FOR 6030Y1 WHIRLPOOL
60 x 30 x 5 In. (524 x 762 x 38mm)
73 Lbs. (33 Kg.)
45 Lbs. (88 Kg.)
4 Gal. (55 L)
29 Gal. (0 L)
46 In. L (68mm L)
53 In. L (346mm L)
in (279mm L)
33 Lbs./Sq.Ft. (62 Kgs./Sq.m)
7.3
8.9ft
3
.25 HP, 9.7 AMPS ,20V.WHIRLPOOL PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
NOTEs:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP
OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIALS BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
● FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING AND DRAIN OVERFLOW. MOUNTING HOLES DRILLED BY INSTALLER.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z24..
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet.
10"
STUD LAYOUT
59-7/8"
(1521mm)
31-1/2"
(800mm)
60"
(800mm)
(254mm)
10"
6" (154mm)
14" (355mm)
8"
(203mm)
Drain C
Floor Cut Out
6" x 10" (154 x 254mm)
= Stud Location
L
30"
(762mm)
15"
(381mm)
ACRYLUX
™
60" x 30" w/INTEGRAL APRON
WHIRLPOOL AND BATHING POOL
HIGH GLOss
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard 6030Y1BW.020 Specification
-
-
-
-
-
-
-
-
-
