2. American Standard
  3. ACRYLUX 6030Y2A.202

American Standard ACRYLUX 6030Y2A.202, Acrylux w/ Integral Apron AFR Whirlpool and Bathing Pool 6030Y2A.102 Features & Dimensions

  • Hello! I am an AI chatbot trained to assist you with the American Standard ACRYLUX 6030Y2A.202 Features & Dimensions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
H127
© 2008 AS America Inc.
ACRYLUX
™
60" x 30" w/INTEGRAL APRON
AFR WHIRLPOOL AND BATHING POOL
HIGH GLOSS
ACRYLUX 60" x 30" w/INTEGRAL APRON
ABOVE-FLOOR-ROUGH
❑ 6030Y2A.102 AFR Bathing Pool, Right Drain
❑ 6030Y2A.202 AFR Bathing Pool, Left Drain
Product Features:
• Above-oor-rough installation
• High-gloss acrylic-capped ABS with
berglass reinforcement
• Integral apron
• Integral three-sided, tiling/water retention ange
• Integral lumbar support
• Pre-leveled tub bottom
❑ 6030Y2A.118 AFR Whirlpool, Right Drain
❑ 6030Y2A.218 AFR Whirlpool, Left Drain
Whirlpool Features:
• 1.25 hp, single-speed pump motor
• 6 whirlpool jets
– 4 adjustable jets
– 2 mini-jets in the lumbar area
• Deck mounted air on/off switch
• Removable access panel
Nominal Dimensions:
59-7/8" x 30" x 18"
(1521 x 762 x 457mm)
For use with:
• 6030Y1.BW Bath Wall Set
• 6030Y1.BWT Bath Tile Wall Set
• Tub can also be installed without
Acrylux wall set
Compliance Certications -
Meets or Exceeds the Following Specications:
• UL 1795 for Hydromassage Bathtubs
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
Revised 5/08
H128
© 2008 AS America Inc.
ACRYLUX
™
60" x 30" w/INTEGRAL APRON
AFR WHIRLPOOL AND BATHING POOL
HIGH GLOSS
GENERAL SPECIFICATIONS FOR 6030Y2A WHIRLPOOL
60 x 30 x 18 In. (1524 x 762 x 457mm)
75 Lbs. (34 Kg.)
458 Lbs. (208 Kg.)
46 Gal. (174 L)
40 Gal. (151 L)
44.5 In. L (1130mm L)
56 In. L (1422mm L)
11 in (279mm L)
37 Lbs./Sq.Ft. (179 Kgs./Sq.m)
7.3
18.91ft
3
1.25 HP, 9.7 AMPS ,120V.WHIRLPOOL PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
GENERAL SPECIFICATIONS FOR 6030Y2A BATHING POOL
60 x 30 x 18 In. (1524 x 762 x 457mm)
53 Lbs. (24 Kg.)
428 Lbs. (194 Kg.)
45 Gal. (170 L)
44.5 In. L (1130mm L)
56 In. L (1422mm L)
11 in (279mm L)
34 Lbs./Sq.Ft. (167 Kgs./Sq.m)
7.3
18.911ft
3
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP
OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIALS BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
● FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING AND DRAIN OVERFLOW. MOUNTING HOLES DRILLED BY INSTALLER.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet.
STUD LAYOUT
10"
31-1/2"
(800mm)
60"
(800mm)
(254mm)
10"
6" (154mm)
14" (355mm)
8"
(203mm)
Drain C
Floor Cut Out
6" x 10" (154 x 254mm)
= Stud Location
L
59-7/8"
(1521mm)
30"
(762mm)
18"
(457mm)
19"
(482mm)
1"
(25mm)
Revised 5/08
/