Whirlpool AWM 020 Program Chart

Whirlpool
Brand
Whirlpool
Model
AWM 020
Category
Washing machines
Type
Program Chart
PROGRAMME GUIDE
GB
*) Appliance with max. spin speed greater than 900 rpm: To protect the wash, the real spin speed is here reduced to 900 rpm.
**) The Programme Duration indicated is an approximate value for a programme with maximum temperature but without special options.
Indicator:
Water Stop
Indicator:
Door lock
Wash Rinse Spin
h
Start preselection
min
Time remaining
(if available)
Programme Care label Type of fabric /
Degree of soiling
Max.
Load
Detregent and
Additives
Selectable special options =
❉
Programme
Selector
Pro-
gramme
Duration
**)
Notes
Sof-
tener
Main
Wash
Pre-
wash
Start
preselection
h
Energy
save
Quick
Wash
Intensive
Rinse
Rinse
Hold
Pre-
wash
Spin
Kg
approx.
min.
Cotton
Slightly to normally soiled
bed linen, table linen,
underwear, towels, shirts
etc. made of cotton and
linen
Normal 5,0
Quick
Wash 3,0
❉
yes
❉❉ ❉
❉
max °60
❉❉❉❉
Cotton
95°
115
Quick
Wash: 60
For heavily soiled washing,
Prewash can be selected in
addition. If “Quick Wash” is
selected, the “Energy save”
special option cannot be
selected.
Cotton
Slightly to normally
soiled bed linen, table
linen, underwear,
towels, shirts etc. made
of cotton and linen
Normal 5,0
Quick
Wash 3,0
❉
yes
❉❉ ❉❉❉❉❉❉
Cotton
60°, 40°, 30°
110
Quick
Wash: 60
For heavily soiled washing,
Prewash can be selected in
addition. If “Quick Wash” is
selected, the “Energy save”
special option cannot be
selected.
Easy Care
Slightly to normally soiled
blouses, shirts, overalls
etc. made of polyester
(Diolen, Trevira),
polyamide (Perlon, Nylon)
or blends with cotton
Normal 2,5
Quick
Wash 1,5
❉
yes
❉❉ ❉❉❉❉❉
❉
*)
Easy Care
60°,50°,
40°, 30°
80
Quick
Wash: 40
If “Quick Wash” is selected,
the “Energy save” special
option cannot be selected.
Delicates
Curtains, delicate
dresses, skirts, shirts
and blouses
1,5
❉
yes
❉❉
—— —
❉❉
❉
*)
Delicates
40°, 30°
45 —
Wool
Only woollens with a
felt-free finish, labelled
with the woolmark and
identified as machine
washable
1
❉
yes
❉❉
—— —
❉❉
❉
*)
Wool
40°
35
If you select “Rinse Hold”, do
not leave the wash in the
rinsing water for too long.
Rinse +
Spin
—5
❉
—— — — —
❉❉
—
❉
Rinse +
Spin
+
—
Programme for treating wash
with starch or softener.
Subsequent spinning is
intensive. Same as the spin
programme in the Coloured
Wash programme.
Gentle Spin — 5 — — — — — — — — —
❉
*)
Gentle Spin
—
Gentle Spin can be used in this
programme. Same as the spin
cycle in the Wool programme.
Drain — — — — — — — — — — — — —
Empt only - do not spin.
Alternative way of terminating
programmes after “Rinse Hold”.
5019 100 03560
AWM 020
Prewash cycle increases programme duration by approx. 15 minutes.
Consumption data were measured in normalised conditions in compliance with Standard IEC 60456.
The data on the energy label refers to the “Cotton 60°C” programme when using the “Energy save” special option.
Consumption values in the home may vary with respect to the values in the table depending on the water pressure,
the water supply temperature, the load and the type of wash.
*) The Time remaining indicator (if available) may also vary from the values in the table, since the particular house-
hold conditions are taken into account by the Time remaining indicator.
FOR DAILY USE:
1. Turn on the water supply tap.
2. Sort and load the laundry by fabric type and colour.
3. Close the door.
4. Add detergent and additives.
5. Select the programme, the temperature and special options.
6. The light above the “Start” button flashes. Press the “Start” button for about one second.
NOTE:
During the first 15 minutes of Cotton and Easy Care programmes (each without Prewash)
you can open the door to add items to the wash.
This is not possible with “Quick Wash”.
CHANGING A PROGRAMME:
a) SELECT NEW PROGRAMME AND CONTINUE
1.Select new programme.
2.The light above the “Start” button flashes. Press the “Start” button for about one sec-
ond.
The new programme will continue from the same programme step where the running
programme was interrupted.
b) TO CANCEL A PROGRAMME THAT IS ALREADY RUNNING AND START A NEW
PROGRAMME
There's no need to add more detergent when you start the new programme, because no
water is drained out when you cancel the programme.
1.Hold down the “Start” button for five seconds, or until the programme control audibly
restarts and the time remaining indicator shows “0”.
2.Wait until the programme sequence indicator returns to the left.
3.Set the programme selector to “0”.
4.Set the programme selector to the new programme, and select any new
special options you require.
5.The light above the “Start” button flashes. Press the “Start” button for about one second.
TO INTERRUPT THE PROGRAMME - PAUSE:
To interrupt the running programme for a certain period and continue it at a later time:
1. Set the programme selector to “0”.
2. Set the programme again after the desired pause.
3. Press the “Start” button for about one minute.
TROUBLESHOOTING GUIDE:
Your washing machine is equipped with automatic safety functions for the early detection
and indication of any possible faults, and for reacting appropriately.
Often these are no more than minor problems that can be solved quickly. Examples of these are:
• The appliance fails to start.
• Aftertreatment agents not fully washed in.
• The appliance vibrates during the spin cycle.
• Load not completely spun at the end of the programme.
Advice on these points can be found in the instructions for use in the “Troubleshooting
Guide” section.
What to do if the washing machine safety system detects a fault.
The programme is interrupted and the various indicators show the fault:
Programme Temperature
Selector
Max. Load Special
Option
Water Energy Programme
Duration *)
(°C) (kg) (l) (kWh) (Min.)
Cotton 95 5
—
57 1,70 115
Cotton 95 5 Energy save 49 1,10 120
Cotton 60 5 Energy save 49 0,95 125
Cotton 60 5
—
49 1,10 110
Cotton 60 2,5
—
38 0,90 105
Cotton 40 5
—
49 0,55 95
Cotton 30 3 Quick Wash 32 0,25 45
Easy Care 60 2,5
—
59 0,70 90
Easy Care 40 2,5
—
53 0,50 80
Easy Care 30 1,5 Quick Wash 36 0,20 35
Delicates 40 1,5
—
55 0,50 50
Wool 40 1
—
55 0,50 40
INDICATOR LIGHTS FLASH DIGITAL DISPLAY
(if available)
WHAT TO DO?
Proceed as per the instructions in
the following section...
“Start” and “Water Stop” Time remaining
(a number between 15 and 99)
“Fault in water supply”
“Speed”, “Water Stop”,
“Time remaining”, “Start preselection”
E1 “Fault in water supply”
“Speed”, “Water Stop”,
“Time remaining”, “Start preselection”
E3 “Fault when draining”
“Speed”, “Time Remaining”,
“Start preselection” flash
E4 or E5 or E6 or E7 or E8 or E9 “Fault in an electrical Component”
For appliances with Water Stop:
“Speed”, “Water Stop”,
“Time remaining”, “Startpreselection”
E2 “Water Stop fault”
Power and water consumption data
GB
  • Page 1 1
  • Page 2 2

Whirlpool AWM 020 Program Chart

Whirlpool
Brand
Whirlpool
Model
AWM 020
Category
Washing machines
Type
Program Chart
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents