2. Golden Lighting
  3. 7011-BA2 PW-CLR

Golden Lighting 7011-BA2 PW-CLR Operating instructions

  • Hello! I've reviewed the Assembly Instructions for the Golden Lighting 7011-BA2 light fixture. This document details the necessary steps for installation, including preparation, wiring, and finishing. I'm ready to answer your questions about the installation process or any other aspects of the fixture described in these instructions.
  • What should be done before starting the installation?
    What wires should be connected together?
    What should be done if there is no ground wire from the junction box?
IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
CONNECTING THE WIRES
4.Attachthexture’swirestothehousewiresfromthe
junctionbox.Connectblacktoblack(orsmooth);whiteto
white(orribbed);groundtoground(greenorcopper).Twist
theendsofthewirepairstogether,thentwistonawire
connector.Makesurealltwistsareinthesamedirection.If
thereisnogroundwire(greenorcopper)fromthejunction
box,locategroundscrew(C)onmountingstrap(B)andwrap
thexture’sgroundwirearoundthegreengroundscrew
(C).Useascrewdrivertosecuregroundscrew(C)ontothe
mountingbracket.Tuckallwiresneatlyintothejunctionbox.
For Customer Service, please
contact the place of purchase.
AssemblyInstructions:7011-BA2 (Winslett)
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the
important notes above. Shut off the power at the circuit
breaker and completely remove the old xture from the
wall, including the old mounting strap.
1.Mountingstrap(B)containsseveralpairsofthreadedholes
andtwosetsofmountingscrews(A&E).Youmayneedto
tightenhexnuts(D)thatholdmountingscrews(A)inplace.
2.Placemountingstrap(B)uptoyourjunctionbox.Place
backplate(F)overthemountingstrapliningupmounting
screws(A)withtheholesinbackplate(F).Thiswillallowyou
toensurethatyouarehangingthexturestraight.Putthe
backplateasidefornow.
3.Pullthehousewiresthroughthecenterofmountingstrap(B).
Securemountingstrap(B)tothejunctionboxwithmounting
screws(E)andascrewdriver.Tightenthescrewssecurely.
FINISHING THE INSTALLATION
5.Placethexture’sbackplate(F)overmountingstrap(B)sothatthemountingscrews(A)protrudefrombackplate(F).Secure
thebackplatetothemountingstrapbythreadingdeconuts(G)ontotheexposedendsofthemountingscrews(A).Twistuntilthe
backplate(F)issnugagainstthewall.
6.Slideglassshades(I)oversockets(H).Securetheglassshadesinplacewithsocketcap(J).
Installlightbulbs(notprovided)basedonthexture’sspecications.Donotexceedthemaximumwattage.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth Ribbed Bare Metal,
Green, or
Green Inner
Thread
Black White
Black Inner
Thread
White Inner
Thread
A
JUNCTION
BOX BCDEF
G
J
I
H
/