ASROCK 4Core1600P35-WiFi User manual

11

1

4Core1600P35-WiFi+ /

4Core1600P35-WiFi

User Manual

Version 1.0

Published December 2007

22

2

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this manual may be reproduced, transcribed, transmitted, or translated in

any language, in any form or by any means, except duplication of documentation by

the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this manual may or may not be regis-

tered trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this manual are furnished for informa-

tional use only and subject to change without notice, and should not be constructed

as a commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this manual.

With respect to the contents of this manual, ASRock does not provide warranty of

any kind, either expressed or implied, including but not limited to the implied warran-

ties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the manual or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

33

3

ContentsContents

Contents

1 Introduction1 Introduction

1 Introduction ......................................................................................................

......................................................................................................

................................................... 5 5

5 5

5

1.1 Package Contents .......................................................... 5

1.2 Specifications ................................................................. 6

1.3 Minimum Hardware Requirement Table for Windows®

VistaTM Premium 2008 and Basic Logo......................... 10

1.4 Motherboard Layout (4Core1600P35-WiFi+) ................... 11

1.5 Motherboard Layout (4Core1600P35-WiFi) ..................... 12

1.6 ASRock 1394_eSATAII I/O Plus (4Core1600P35-WiFi+) . 13

1.7 ASRock 8CH_eSATAII I/O Plus (4Core1600P35-WiFi) .... 14

1.8 ASRock WiFi-802.11g Module Specifications ................. 15

2 Installation2 Installation

2 Installation..........................................................................................................

..........................................................................................................

..................................................... 16 16

16 16

16

2.1 Screw Holes ................................................................... 16

2.2 Pre-installation Precautions ............................................ 16

2.3 CPU Installation .............................................................. 17

2.4 Installation of Heatsink and CPU fan ............................... 19

2.5 Installation of Memory Modules (DIMM) ......................... 20

2.6 Expansion Slots (PCI and PCI Express Slots) ..................... 23

2.7 CrossFireTM Operation Guide .......................................... 23

2.8 Surround Display Feature ............................................... 27

2.9 Jumpers Setup ............................................................... 28

2.10 Onboard Headers and Connectors .................................. 30

2.11 HDMI_SPDIF Header Connection Guide ......................... 36

2.12 eSATAII Interface Introduction ......................................... 37

2.13 SATAII Hard Disk Setup Guide ........................................ 40

2.14 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks

Installation ...................................................................... 41

2.15 Hot Plug and Hot Swap Functions for SATA / SATAII

HDDs and eSATAII Devices ......................................... 42

2.16 SATA / SATAII HDD Hot Plug Feature and Operation

Guide ............................................................................. 43

2.17 Driver Installation Guide ................................................... 45

2.18 Installing Windows® XP / XP 64-bit / VistaTM / VistaTM

64-bit With RAID Functions ............................................ 45

2.18.1 Installing Windows® XP / XP 64-bit With RAID

Functions ............................................................ 45

2.18.2 Setting Up a “RAID Ready” System .................... 46

2.18.3 Migrating a “RAID Ready” System to RAID 0,

RAID 1 or RAID 5 ................................................ 47

2.18.4 Installing Windows® VistaTM / VistaTM 64-bit With

RAID Functions ................................................... 48

44

4

2.19 Installing Windows® 2000 / XP / XP 64-bit / VistaTM /

VistaTM 64-bit Without RAID Functions ........................... 49

2.19.1 Installing Windows® 2000 / XP / XP 64-bit Without

RAID Functions ................................................... 49

2.19.2 Installing Windows® VistaTM / VistaTM 64-bit Without

RAID Functions ................................................... 50

2.20 DTS Operation Guide .................................................. 51

2.21 Untied Overclocking Technology ................................... 53

3 BIOS S3 BIOS S

3 BIOS SETUP UTILITYETUP UTILITY

ETUP UTILITYETUP UTILITY

ETUP UTILITY....................................................................................

....................................................................................

.......................................... 54 54

54 54

54

3.1 Introduction ..................................................................... 54

3.1.1 BIOS Menu Bar ..................................................... 54

3.1.2 Navigation Keys .................................................... 55

3.2 Main Screen ................................................................... 55

3.3 Advanced Screen ............................................................ 56

3.3.1 CPU Configuration ................................................ 57

3.3.2 Chipset Configuration ............................................ 59

3.3.3 ACPI Configuration ................................................ 61

3.3.4 IDE Configuration .................................................. 62

3.3.5 PCIPnP Configuration ........................................... 65

3.3.6 Floppy Configuration ............................................. 66

3.3.7 Super IO Configuration .......................................... 66

3.3.8 USB Configuration ................................................ 68

3.4 Hardware Health Event Monitoring Screen ...................... 68

3.5 Boot Screen ................................................................... 69

3.5.1 Boot Settings Configuration ................................... 70

3.6 Security Screen .............................................................. 70

3.7 Exit Screen .................................................................... 71

4 Software Support4 Software Support

4 Software Support ....................................................................................

....................................................................................

.......................................... 72 72

72 72

72

4.1 Install Operating System ................................................ 72

4.2 Support CD Information ................................................... 72

4.2.1 Running Support CD ............................................. 72

4.2.2 Drivers Menu ......................................................... 72

4.2.3 Utilities Menu ........................................................ 72

4.2.4 Contact Information ............................................... 72

55

5

Chapter 1: IntroductionChapter 1: Introduction

Chapter 1: Introduction

Thank you for purchasing ASRock 4Core1600P35-WiFi+ / 4Core1600P35-WiFi

motherboard, a reliable motherboard produced under ASRock’s consistently stringent

quality control. It delivers excellent performance with robust design conforming to ASRock’s

commitment to quality and endurance.

In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-step

guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to

BIOS setup and information of the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specific information about the model you are using.

www.asrock.com/support/index.asp

1.1 P1.1 P

1.1 Packack

ackack

ackage Contentsage Contents

age Contentsage Contents

age Contents

ASRock 4Core1600P35-WiFi+ / 4Core1600P35-WiFi Motherboard

(ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm)

ASRock 4Core1600P35-WiFi+ / 4Core1600P35-WiFi Quick Installation Guide

ASRock 4Core1600P35-WiFi+ / 4Core1600P35-WiFi Support CD

ASRock WiFi-802.11g Module Operation Guide

Motherboard Accessories

One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

Four Serial ATA (SATA) Data Cables (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional)

One HDMI_SPDIF Cable (Optional)

One “ASRock 1394_eSATAII I/O Plus” I/O Panel Shield (4Core1600P35-WiFi+)

One “ASRock 8CH_eSATAII I/O Plus” I/O Panel Shield (4Core1600P35-WiFi)

WiFi Accessories

One ASRock WiFi-802.11g Module

One Antenna

One WiFi Bracket

66

6

1.21.2

1.2 SpecificationsSpecifications

SpecificationsSpecifications

Specifications

Platform - ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm

- All Solid Capacitor design

CPU - LGA 775 for Intel® CoreTM 2 Extreme / CoreTM 2 Quad / CoreTM

2 Duo / Pentium® Dual Core / Celeron®, supporting Penryn Quad

Core Yorkfield and Dual Core Wolfdale processors

- Compatible with all FSB1600/1333/1066/800MHz CPUs

(see CAUTION 1)

- Supports Hyper-Threading Technology (see CAUTION 2)

- Supports Untied Overclocking Technology (see CAUTION 3)

- Supports EM64T CPU

Chipset - Northbridge: Intel® P35

- Southbridge: Intel® ICH9R

Memory - Dual Channel DDR3/DDR2 Memory Technology

(see CAUTION 4)

- 2 x DDR3 DIMM slots (green)

- Support DDR3 1333/1066/800 non-ECC, un-buffered memory

(see CAUTION 5)

- Max. capacity: 4GB (see CAUTION 6)

- 4 x DDR2 DIMM slots (yellow and orange)

- Support DDR2 1066/800/667 non-ECC, un-buffered memory

(see CAUTION 5)

- Max. capacity: 8GB (see CAUTION 6)

Expansion Slot - Supports ATITM CrossFireTM

- 1 x PCI Express x16 slot

- 1 x AGI Express slot (PCI Express x4)

- 3 x PCI slots

Audio 4Core1600P35-WiFi+

- 7.1 CH Windows® VistaTM Premium Level HD Audio with

Content Protection

- DAC with 110dB dynamic range (ALC890 Audio Codec)

- DTS (Digital Theater Systems) support (see CAUTION 7)

4Core1600P35-WiFi

- 7.1 CH Windows® VistaTM Premium Level HD Audio with

Content Protection

- DAC with 110dB dynamic range (ALC890 Audio Codec)

LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111B/RTL8111C

- Supports Wake-On-LAN

77

7

Wireless LAN - ASRock WiFi-802.11g module

- 54Mbps IEEE 802.11g / 11Mbps IEEE 802.11b

- Supports Software Access Point mode (AP mode) and

Station mode (Infrastructure mode and Ad-hoc mode)

Rear Panel I/O 4Core1600P35-WiFi+

ASRock 1394_eSATAII I/O Plus

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

- 1 x Parallel Port (ECP/EPP Support)

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x eSATAII Port

- 1 x RJ-45 LAN Port

- 2 x RJ-45 LAN Port LED (ACT/LINK LED and SPEED LED)

- 1 x IEEE 1394 Port

- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

Line in/Front Speaker/Microphone (see CAUTION 8)

4Core1600P35-WiFi

ASRock 8CH_eSATAII I/O Plus

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

- 1 x Parallel Port (ECP/EPP Support)

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x eSATAII Port

- 1 x RJ-45 LAN Port

- 2 x RJ-45 LAN Port LED (ACT/LINK LED and SPEED LED)

- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

Line in/Front Speaker/Microphone (see CAUTION 8)

Connector - 6 x SATAII 3.0Gb/s connectors, support RAID (RAID 0,

RAID 1, RAID 10, RAID 5 and Intel Matrix Storage), NCQ,

AHCI and “Hot Plug” functions (see CAUTION 9)

- 1 x eSATAII 3.0Gb/s connector (shared with 1 SATAII

connector) (see CAUTION 10)

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x DeskExpress Hot Plug Detection header

- 1 x HDMI_SPDIF header

- 1 x IEEE 1394 header (4Core1600P35-WiFi+)

- CPU/Chassis FAN connector

88

8

- 24 pin ATX power connector

- 8 pin 12V power connector

- SLI/XFIRE power connector

- CD in header

- Front panel audio connector

- 3 x USB 2.0 headers (support 6 USB 2.0 ports)

(see CAUTION 11)

- 1 x WiFi header (see CAUTION 12)

BIOS Feature - 8Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- AMBIOS 2.3.1 Support

- CPU, DRAM, NB, SB, VTT Voltage Multi-adjustment

- Supports I. O. T. (Intelligent Overclocking Technology)

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Unique Feature - ASRock OC Tuner (see CAUTION 13)

- Hybrid Booster:

- CPU Frequency Stepless Control (see CAUTION 14)

- ASRock U-COP (see CAUTION 15)

- Boot Failure Guard (B.F.G.)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore

OS - Microsoft® Windows® 2000 / XP / XP 64-bit / VistaTM /

VistaTM 64-bit compliant (see CAUTION 16)

Certifications - FCC, CE, WHQL

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting

the setting in the BIOS, applying Untied Overclocking Technology, or using the third-

party overclocking tools. Overclocking may affect your system stability, or even

cause damage to the components and devices of your system. It should be done at

your own risk and expense. We are not responsible for possible damage caused by

overclocking.

99

9

CAUTION!

1. FSB1600-CPU will operate in overclocking mode. If you use a FSB1600-

CPU on this motherboard, you need to adjust the jumpers. Please refer

to page 29 for proper jumper settings. Besides, if you want to change a

new CPU on this motherboard, please remove the AC power cord from

your PC in advance.

2. About the setting of “Hyper Threading Technology”, please check page

56.

3. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 53 for details.

4. This motherboard supports Dual Channel Memory Technology. Before

you implement Dual Channel Memory Technology, make sure to read

the installation guide of memory modules on page 20 for proper

installation.

5. Please check the table below for the CPU FSB frequency and its

corresponding memory support frequency.

CPU FSB Frequency Memory Support Frequency

1600 DDR2 800, DDR2 1066,

DDR3 1066, DDR3 1333

1333 DDR2 667, DDR2 800, DDR2 1066,

DDR3 800, DDR3 1066, DDR3 1333

1066 DDR2 667, DDR2 800, DDR2 1066,

DDR3 800, DDR3 1066

800 DDR2 667, DDR2 800,

DDR3 800

* DDR2 1066 and DDR3 1333 memory modules will operate in

overclocking mode.

* When you use a FSB1600-CPU on this motherboard, it will run at

DDR2 960 if you adopt a DDR2 1066 memory module. When you

use a FSB1600-CPU on this motherboard, it will run at DDR3 960

if you adopt a DDR3 1066 memory module. When you use a

FSB1600-CPU on this motherboard, it will run at DDR3 1280 if you

adopt a DDR3 1333 memory module.

* If you adopt a DDR2 1066 memory module and adopt a FSB1333-

CPU or FSB1066-CPU on this motherboard, you need to adjust the

jumpers. Please refer to page 29 for proper jumper settings.

6. Due to the operating system limitation, the actual memory size may be

less than 4GB for the reservation for system usage under Windows® XP

and Windows® VistaTM. For Windows® XP 64-bit and Windows® VistaTM

64-bit with 64-bit CPU, there is no such limitation.

7. DTS (Digital Theater Systems) is a multi-channel digital surround sound

format. To enable DTS function, you need to adjust the settings after

audio driver installation. Please refer to “DTS Operation Guide” on page

51 for details.

8. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-

channel, 6-channel, and 8-channel modes. Please check the table on

page 13 and 14 for proper connection.

1010

10

1.31.3

1.3 Minimum Hardware RMinimum Hardware R

Minimum Hardware RMinimum Hardware R

Minimum Hardware Requirement Tequirement T

equirement Tequirement T

equirement Table for Wable for W

able for Wable for W

able for Windowsindows

indowsindows

indows®®

®®

®

VistaVista

VistaTMTM

TMTM

TM Premium 2008 and Basic Logo Premium 2008 and Basic Logo

Premium 2008 and Basic Logo Premium 2008 and Basic Logo

Premium 2008 and Basic Logo

For system integrators and users who purchase this motherboard and

plan to submit Windows® VistaTM Premium 2008 and Basic logo, please

follow below table for minimum hardware requirements.

CPU Celeron 420

Memory 1GB system memory (Premium)

512MB Single Channel (Basic)

VGA DX10 with WDDM Driver

with 128bit VGA memory (Premium)

with 64bit VGA memory (Basic)

* After June 1, 2008, all Windows® VistaTM systems are required to meet above

minimum hardware requirements in order to qualify for Windows® VistaTM

Premium 2008 logo.

9. Before installing SATAII hard disk to SATAII connector, please read the

“SATAII Hard Disk Setup Guide” on page 40 to adjust your SATAII hard

disk drive to SATAII mode. You can also connect SATA hard disk to SATAII

connector directly.

10. This motherboard supports eSATAII interface, the external SATAII

specification. Please read “eSATAII Interface Introduction” on page 37

for details about eSATAII and eSATAII installation procedures.

11. Power Management for USB 2.0 works fine under Microsoft® Windows®

VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4.

12. WiFi header supports WiFi+AP function with ASRock WiFi-802.11g or

WiFi-802.11n module, an easy-to-use wireless local area network

(WLAN) adapter. It allows you to create a wireless environment and

enjoy the convenience of wireless network connectivity.

13. It is a user-friendly ASRock overclocking tool which allows you to surveil

your system by hardware monitor function and overclock your hardware

devices to get the best system performance under Windows®

environment. Please visit our website for the operation procedures of

ASRock OC Tuner. ASRock website: http://www.asrock.com

14. Although this motherboard offers stepless control, it is not recom-

mended to perform over-clocking. Frequencies other than the recom-

mended CPU bus frequencies may cause the instability of the system

or damage the CPU.

15. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC

system.

16. ASRock WiFi-802.11g module and RAID / AHCI functions are not

supported under Windows® 2000 OS. It is recommended to use IDE

mode under Windows® 2000. Please refer to page 62 for detailed setup.

1111

11

1.4 Motherboard L1.4 Motherboard L

1.4 Motherboard Layout (4Core1600P35-ayout (4Core1600P35-

ayout (4Core1600P35-ayout (4Core1600P35-

ayout (4Core1600P35-WW

WW

WiFiF

iFiF

iFi+)i+)

i+)i+)

i+)

Intel

P35

Chipset

Intel

ICH9R

ATXPWR1

CD1

ATX12V1

1

PS2_USB_PWR1

Super

I/O

8Mb

BIOS

LAN

PHY

AUDIO

CODEC

PCIE1

CPU_FAN1

CMOS

Battery

PCI

EXPRESS

4Core1600P35-WiFi+

DDR2 1066

Quad Core CPU

IDE1

CLRCMOS1

1

CHA_FAN1

FLOPPY1

1

HD_AUDIO1

HDLED RESET

PLED PWRBTN

SPEAKER1

1

PANEL1

1

WIFI

30.5cm (12.0 in)

24.4cm (9.6 in)

12345678

9

10

11

12

13

14

15

16

24

25 23 1718

19

20

2122

26

27

28

29

30

31

32

DDRII_1 (64 bit, 240-pin module)

DDRII_2 (64 bit, 240-pin module)

RoHS

Wolfdale

Dual Channel

7.1CH HD

SATAII

1

HDMI_SPDIF1

IR1

1

USB4_5

11

Yorkfield

Gigabit LAN

SATAII_3(Port2)

SATAII_4(Port3)

FSB1600

FSB1

1

FSB2

1

FSB3

1

Top:

SIDE SPK

Center:

REAR SPK

Bottom:

CTR BASS

Top:

LINE IN

Center:

FRONT

Bottom:

MIC IN

AGI_EXPRESS1

PCI1

PCI2

PCI3

DDR3_A1 (64 bit, 240-pin module)

DDRII_3 (64 bit, 240-pin module)

DDRII_4 (64 bit, 240-pin module)

DDR3_B1 (64 bit, 240-pin module)

USB6_7

11

USB8_9

11

SATAII_5(Port4)

SATAII_6(Port5)

SATAII_1(Port0)

SATAII_2(Port1)

DDR3 1333

USB2.0

eSATAII

ESATAII

RAID

ATA133

SLI/XFIRE_PWR1

PARALLEL PORT

COM1

PS2

Mouse

PS2

Keyboard

ESATAII

USB 2.0

T: US B0

B: USB1

Top:

RJ-45

USB 2.0

T: US B2

B: USB3

33

34

35

36

Top:

IEEE

1394

FRONT_1394

11

37

38

39

1 PS2_USB_PWR1 Jumper 20 USB 2.0 Header (USB6_7, Blue)

2 ATX 12V Connector (ATX12V1) 21 USB 2.0 Header (USB4_5, Blue)

3 CPU Fan Connector (CPU_FAN1) 22 USB 2.0 Header (USB8_9, Blue)

4 775-Pin CPU Socket 23 South Bridge Controller

5 North Bridge Controller 24 SPI BIOS Chip

6 2 x 240-pin DDR2 DIMM Slots 25 Front Panel IEEE 1394 Header

(Dual Channel A: DDRII_1, DDRII_3; Yellow) (FRONT_1394)

7 2 x 240-pin DDR2 DIMM Slots 26 WiFi Header (WiFi)

(Dual Channel B: DDRII_2, DDRII_4; Orange) 27 DeskExpress Hot Plug Detection Header

8 2 x 240-pin DDR3 DIMM Slots (IR1)

(Dual Channel C: DDR3_A1, DDR3_B1; Green) 28 Floppy Connector (FLOPPY1)

9 IDE1 Connector (IDE1, Blue) 29 HDMI_SPDIF Header (HDMI_SPDIF1)

10 Clear CMOS Jumper (CLRCMOS1) 30 Front Panel Audio Header (HD_AUDIO1)

11 SATAII Connector (SATAII_5 (Port4), Red) 31 Internal Audio Connector: CD1 (Black)

12 SATAII Connector (SATAII_1 (Port0), Red) 32 PCI Slots (PCI1 - 3)

13 Chassis Fan Connector (CHA_FAN1) 33 AGI Express Slot (AGI_EXPRESS1)

14 SATAII Connector (SATAII_2 (Port1), Red) 34 FSB1 Jumper

15 Chassis Speaker Header (SPEAKER 1) 35 FSB2 / FSB3 Jumpers

16 System Panel Header (PANEL1) 36 PCI Express x16 Slot (PCIE1)

17 SATAII Connector (SATAII_3 (Port2), Red) 37 SLI / XFIRE Power Connector

18 SATAII Connector (SATAII_4 (Port3), Red) 38 ATX Power Connector (ATXPWR1)

19 SATAII Connector (SATAII_6 (Port5), Orange) 39 eSATAII Connector (eSATAII)

1212

12

1.5 Motherboard L1.5 Motherboard L

1.5 Motherboard Layout (4Core1600P35-ayout (4Core1600P35-

ayout (4Core1600P35-ayout (4Core1600P35-

ayout (4Core1600P35-WW

WW

WiFiF

iFiF

iFi)i)

i)i)

i)

Intel

P35

Chipset

Intel

ICH9R

ATXPWR1

CD1

ATX12V1

1

PS2_USB_PWR1

Super

I/O

8Mb

BIOS

LAN

PHY

AUDIO

CODEC

PCIE1

CPU_FAN1

CMOS

Battery

PCI

EXPRESS

4Core1600P35-WiFi

DDR2 1066

Quad Core CPU

IDE1

CLRCMOS1

1

CHA_FAN1

FLOPPY1

1

HD_AUDIO1

HDLED RESET

PLED PWRBTN

SPEAKER1

1

PANE L1

1

WIFI

30.5cm (12.0 in)

24.4cm (9.6 in)

12345678

9

10

11

12

13

14

15

16

24

25 23 1718

19

20

2122

26

27

28

29

30

31

32

DDRII_1 (64 bit, 240-pin module)

DDRII_2 (64 bit, 240-pin module)

RoHS

Wolfdale

Dual Channel

7.1CH HD

SATAII

1

HDMI_SPDIF1

IR1

1

USB4_5

11

Yorkfield

Gigabit LAN

SATAII_3(Port2)

SATAII_4(Port3)

FSB1600

FSB1

1

FSB2

1

FSB3

1

Top:

SIDE SPK

Center:

REAR SPK

Bottom:

CTR BASS

Top:

LINE IN

Center:

FRONT

Bottom:

MIC IN

AGI_EXPRESS1

PCI1

PCI2

PCI3

DDR3_A1 (64 bit, 240-pin module)

DDRII_3 (64 bit, 240-pin module)

DDRII_4 (64 bit, 240-pin module)

DDR3_B1 (64 bit, 240-pin module)

USB6_7

11

USB8_9

11

SATAII_5(Port4)

SATAII_6(Port5)

SATAII_1(Port0)

SATAII_2(Port1)

DDR3 1333

USB2.0

eSATAII

ESATAII

RAID

ATA133

SLI/XFIRE_PWR1

PARALLEL PORT

COM1

PS2

Mouse

PS2

Keyboard

ESATAII

USB 2.0

T: US B0

B: USB1

Top:

RJ-45

USB 2.0

T: US B2

B: USB3

33

34

35

36

37

38

1 PS2_USB_PWR1 Jumper 20 USB 2.0 Header (USB6_7, Blue)

2 ATX 12V Connector (ATX12V1) 21 USB 2.0 Header (USB4_5, Blue)

3 CPU Fan Connector (CPU_FAN1) 22 USB 2.0 Header (USB8_9, Blue)

4 775-Pin CPU Socket 23 South Bridge Controller

5 North Bridge Controller 24 SPI BIOS Chip

6 2 x 240-pin DDR2 DIMM Slots 25 WiFi Header (WiFi)

(Dual Channel A: DDRII_1, DDRII_3; Yellow) 26 DeskExpress Hot Plug Detection Header

7 2 x 240-pin DDR2 DIMM Slots (IR1)

(Dual Channel B: DDRII_2, DDRII_4; Orange) 27 Floppy Connector (FLOPPY1)

8 2 x 240-pin DDR3 DIMM Slots 28 HDMI_SPDIF Header (HDMI_SPDIF1)

(Dual Channel C: DDR3_A1, DDR3_B1; Green) 29 Front Panel Audio Header (HD_AUDIO1)

9 IDE1 Connector (IDE1, Blue) 30 Internal Audio Connector: CD1 (Black)

10 Clear CMOS Jumper (CLRCMOS1) 31 PCI Slots (PCI1 - 3)

11 SATAII Connector (SATAII_5 (Port4), Red) 32 AGI Express Slot (AGI_EXPRESS1)

12 SATAII Connector (SATAII_1 (Port0), Red) 33 FSB1 Jumper

13 Chassis Fan Connector (CHA_FAN1) 34 FSB2 / FSB3 Jumpers

14 SATAII Connector (SATAII_2 (Port1), Red) 35 PCI Express x16 Slot (PCIE1)

15 Chassis Speaker Header (SPEAKER 1) 36 SLI / XFIRE Power Connector

16 System Panel Header (PANEL1) 37 ATX Power Connector (ATXPWR1)

17 SATAII Connector (SATAII_3 (Port2), Red) 38 eSATAII Connector (eSATAII)

18 SATAII Connector (SATAII_4 (Port3), Red)

19 SATAII Connector (SATAII_6 (Port5), Orange)

1313

13

1.61.6

1.6 ASRASR

ASRASR

ASRock 1394_eSAock 1394_eSA

ock 1394_eSAock 1394_eSA

ock 1394_eSATT

TT

TAII I/O Plus (4Core1600P35-AII I/O Plus (4Core1600P35-

AII I/O Plus (4Core1600P35-AII I/O Plus (4Core1600P35-

AII I/O Plus (4Core1600P35-WW

WW

WiFiF

iFiF

iFi+)i+)

i+)i+)

i+)

1 PS/2 Mouse Port (Green) ** 9 Front Speaker (Lime)

2 Parallel Port 10 Microphone (Pink)

3 IEEE 1394 Port 11 USB 2.0 Ports (USB01)

* 4 LAN RJ-45 Port 12 USB 2.0 Ports (USB23)

5 Side Speaker (Gray) 13 eSATAII Port

6 Rear Speaker (Black) 14 COM Port

7 Central / Bass (Orange) 15 PS/2 Keyboard Port (Purple)

8 Line In (Light Blue)

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will find “Mixer” tool on your system.

Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click

“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA

Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA

Audio 2nd output” to use front panel audio.

6

7

124

3

58

9

10

11

12

13

14

15

** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output ChannelsFront Speaker Rear Speaker Central / Bass Side Speaker

(No. 9) (No. 6) (No. 7) (No. 5)

2 V -- -- --

4 V -- -- V

6V--VV

8VVVV

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description

Off No link Off 10Mbps connection

Orange Linked Orange 100Mbps connection

Blinking Data Activity Green 1Gbps connection LAN Port

ACT/LINK

LED

SPEED

LED

1414

14

1.71.7

1.7 ASRASR

ASRASR

ASRock 8CH_eSAock 8CH_eSA

ock 8CH_eSAock 8CH_eSA

ock 8CH_eSATT

TT

TAII I/O Plus (4Core1600P35-AII I/O Plus (4Core1600P35-

AII I/O Plus (4Core1600P35-AII I/O Plus (4Core1600P35-

AII I/O Plus (4Core1600P35-WW

WW

WiFiF

iFiF

iFi)i)

i)i)

i)

1 PS/2 Mouse Port (Green) ** 8 Front Speaker (Lime)

2 Parallel Port 9 Microphone (Pink)

* 3 LAN RJ-45 Port 10 USB 2.0 Ports (USB01)

4 Side Speaker (Gray) 11 USB 2.0 Ports (USB23)

5 Rear Speaker (Black) 12 eSATAII Port

6 Central / Bass (Orange) 13 COM Port

7 Line In (Light Blue) 14 PS/2 Keyboard Port (Purple)

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will find “Mixer” tool on your system.

Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click

“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA

Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA

Audio 2nd output” to use front panel audio.

6

7

12

4

3

58

9

10

11

12

13

14

** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output ChannelsFront Speaker Rear Speaker Central / Bass Side Speaker

(No. 8) (No. 5) (No. 6) (No. 4)

2 V -- -- --

4VV----

6VVV--

8VVVV

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description

Off No link Off 10Mbps connection

Orange Linked Orange 100Mbps connection

Blinking Data Activity Green 1Gbps connection LAN Port

ACT/LINK

LED

SPEED

LED

1515

15

1.81.8

1.8 ASRock WiFi-802.11g Module SpecificationsASRock WiFi-802.11g Module Specifications

ASRock WiFi-802.11g Module SpecificationsASRock WiFi-802.11g Module Specifications

ASRock WiFi-802.11g Module Specifications

ASRock WiFi-802.11g module is an easy-to-use wireless local area network (WLAN)

adapter to support WiFi+AP function. With ASRock WiFi-802.11g module, you can

easily create a wireless environment and enjoy the convenience of wireless network

connectivity. Therefore, from anywhere within the signal range, you will be able to play

LAN games, connect to the internet, access and share printers, and make Internet

phone calls easily.

Standard - IEEE 802.11g

Data Rate - 6, 9, 12, 18, 24, 36, 48, 54Mbps

Security - Access Point mode (AP mode): WEP, WPA

Network - Access Point mode (AP mode)

Architecture Types - Station mode: Infrastructure mode and Ad-Hoc mode

Frequency Band - 2.4~2.5GHz

Operating Range - Indoor: 80ft (30m)

Outdoor: 200ft (60m)

* The range varies in different environments

Number of - up to 16 stations

Connected Devices

(AP Mode)

Antenna - ASRock WiFi-802.11g omni-directional antenna

LED - Green data transmission (AIR) LED

Support OS - Windows® XP / XP 64-bit / VistaTM / VistaTM 64-bit

Compatibility - Full compatible with IEEE 802.11g standard products

Software Support - ASRock WiFi-802.11g Wizard

If you want to start to use ASRock WiFi-802.11g module on this motherboard, please

carefully read “ASRock WiFi-802.11g Module Operation Guide” in the package for

the detailed introduction and operation procedures. You can also read the document in

the following path of ASRock motherboard support CD:

..\ ASRock WiFi-802.11g \ Vista64_Vista_XP64_XP

1616

16

Chapter 2: InstallationChapter 2: Installation

Chapter 2: Installation

This is an ATX form factor (12.0" x 9.6", 30.5 x 24.4 cm) motherboard. Before you install

the motherboard, study the configuration of your chassis to ensure that the motherboard

fits into it.

Make sure to unplug the power cord before installing or removing the

motherboard. Failure to do so may cause physical injuries to you and

damages to motherboard components.

2.1 Screw Holes2.1 Screw Holes

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the

chassis.

Do not over-tighten the screws! Doing so may damage the motherboard.

2.2 Pre-installation Precautions2.2 Pre-installation Precautions

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any component.

2. To avoid damaging the motherboard components due to static electricity, NEVER

place your motherboard directly on the carpet or the like. Also remember to use

a grounded wrist strap or touch a safety grounded object before you handle

components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded antistatic pad or

in the bag that comes with the component.

Before you install or remove any component, ensure that the power is

switched off or the power cord is detached from the power supply.

Failure to do so may cause severe damage to the motherboard, peripherals,

and/or components.

1717

17

2.3 CPU Installation2.3 CPU Installation

2.3 CPU Installation

For the installation of Intel 775-LAND CPU,

please follow the steps below.

Before you insert the 775-LAND CPU into the socket, please check if

the CPU surface is unclean or if there is any bent pin on the socket.

Do not force to insert the CPU into the socket if above situation is

found. Otherwise, the CPU will be seriously damaged.

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear

retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Insert the 775-LAND CPU:

Step 2-1. Hold the CPU by the edges where are

marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two

orientation key notches.

775-Pin Socket Overview

black line

775-Pin Socket

Pin1

alignment key alignment key

Pin1

orientation

key notch orientation

key notch

775-LAND CPU

1818

18

For proper inserting, please ensure to match the two orientation key

notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket

by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket

and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick and Place Cap):

Use your left hand index finger and thumb to

support the load plate edge, engage PnP cap

with right hand thumb and peel the cap from the

socket while pressing on center of PnP cap to

assist in removal.

1. It is recommended to use the cap tab to handle and avoid kicking

off the PnP cap.

2. This cap must be placed if returning the motherboard for after

service.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.

Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

1919

19

2.42.4

2.4 Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

This motherboard is equipped with 775-Pin socket that supports Intel 775-LAND CPU.

Please adopt the type of heatsink and cooling fan compliant with Intel 775-LAND CPU

to dissipate heat. Before you installed the heatsink, you need to spray thermal

interface material between the CPU and the heatsink to improve heat dissipation.

Ensure that the CPU and the heatsink are securely fastened and in good contact with

each other. Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1, see

page 11/12, No. 3).

For proper installation, please kindly refer to the instruction manuals of

your CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-LAND CPU.

Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the

CPU fan connector on the motherboard

(CPU_FAN1, see page 11/12, No. 3).

Step 3. Align fasteners with the motherboard

throughholes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install

and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise,

the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan

connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or

contact other components.

2020

20

2.5 Installation of Memor2.5 Installation of Memor

2.5 Installation of Memory Modules (DIMM)y Modules (DIMM)

y Modules (DIMM)y Modules (DIMM)

y Modules (DIMM)

This motherboard provides four 240-pin DDR2 (Double Data Rate 2) DIMM slots and

two 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel

Memory Technology. For dual channel configuration, you always need to install

identical (the same brand, speed, size and chip-type) DDR2/DDR3 DIMM pair in

the slots of the same color. In other words, you have to install identical DDR2

DIMM pair in Dual Channel A (DDRII_1 and DDRII_3; Yellow slots; see p.11/12 No.

6), identical DDR2 DIMM pair in Dual Channel B (DDRII_2 and DDRII_4; Orange

slots; see p.11/12 No.7), or identical DDR3 DIMM pair in Dual Channel C (DDR3_A1

and DDR3_B1; Green slots; see p.11/12 No.8), so that Dual Channel Memory Tech-

nology can be activated. This motherboard also allows you to install four DDR2

DIMMs for dual channel configuration, and please install identical DDR2 DIMMs in

all four slots. You may refer to the Dual Channel Memory Configuration Table below.

Dual Channel DDR2 Memory Configurations

(DS: Double Side, SS: Single Side)

DDRII_1 DDRII_2 DDRII_3 DDRII_4

(Yellow Slot) (Orange Slot) (Yellow Slot) (Orange Slot)

2 memory modules SS X SS X

2 memory modules DS X DS X

2 memory modules X SS X SS

2 memory modules X DS X DS

4 memory modules SS SS SS SS

4 memory modules DS DS DS DS

DDR3_A1 DDR3_B1

(Green Slot) (Green Slot)

2 memory modules SS SS

2 memory modules DS DS

Dual Channel DDR3 Memory Configurations

(DS: Double Side, SS: Single Side)

Page is loading ...

ASROCK 4Core1600P35-WiFi User manual

This manual is also suitable for

ASROCK 4Core1600P35-WiFi User manual

Related papers

Other documents