AmazonBasics B0828YJ33N User manual

Brand: AmazonBasics

Model: B0828YJ33N

Category: Space heaters

Type: User manual

Portable Digital Radiator Heater, Remote Control, 1500W

Radiateur Mobile Numérique, Télécommande, 1500W

Calefactor de Radiador Digital Portátil, Control Remoto, 1500W

B0828YJ33N

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

IMPORTANT INSTRUCTIONS

Read these instructions carefully and retain them for future use.

If this product is passed to a third party, then these instructions

must be included.

When using electrical appliances, basic safety precautions should always

be followed to reduce the risk of ﬁre, electric shock, and/or injury to

persons including the following:

WARNING

Risk of electric shock! To reduce the risk of ﬁre or

electric shock do not use with an extension cord.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

• Read all instructions before using this heater.

• This heater is hot when in use. To avoid burns, do not let bare skin

touch hot surfaces. If provided, use handles when moving this heater.

Keep combustible materials such as furniture, pillows, bedding,

papers, clothes, curtains at least 3 feet (0.9 m) from the front of the

heater and keep away from the sides and rear.

• Extreme caution is necessary when any heater is used by or near

children or invalids and whenever the heater is left operating and

unattended.

• Do not operate any heater with a damaged cord or plug after the

heater malfunctions, has been dropped or damaged by any manner.

Discard heater or return to authorized service facility for examination

and/or repair.

• Do not use outdoors.

• This heater is not intended for use in bathrooms, laundry areas and

similar indoor locations. Never locate heater where it may fall into a

bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs,

runners or similar coverings. Do not route cord under furniture or

appliances. Arrange cord away from trafﬁc area and where it will not

be tripped over.

• To disconnect heater, turn controls to off, then remove plug from

outlet.

• Do not insert or allow foreign objects to enter any ventilation or

exhaust opening as this may cause an electric shock or ﬁre, or

damage the heater. Oil in the heater is permanently sealed and does

not require reﬁlling.

• This heater is ﬁlled with a precise quantity of special oil. Repairs

requiring opening of the oil container are only to be made by a

professional repair center that should be contacted if there is an oil

leak.

• When scrapping the heater, follow the regulations concerning the

disposal of oil.

• A heater has hot and arcing or sparking parts inside. Do not use it In

areas where gasoline, paint or ﬂammable liquids are used or stored.

• Always plug heaters directly into a wall outlet/receptacle. Never use

with an extension cord or relocatable power tap (outlet/power strip).

• To prevent a possible ﬁre, do not block air intakes or exhaust in any

manner. Do not use on soft surfaces, like a bed, where openings may

become blocked.

• This product draws up to 1500 W of power. To prevent overloading of

the electrical circuit, do not plug the product into a circuit with other

appliances already connected.

• The plug in the socket outlet must always be easily accessible so that

it can be disconnected in an emergency.

Polarized Plug

This appliance has a polarized plug (one blade is wider than the other). To

reduce the risk of electric shock, this plug will ﬁt the outlet only one way.

If the plug does not ﬁt fully in the outlet, reverse the plug. If it still does not

ﬁt, contact a qualiﬁed electrician. Do not modify the plug in any way.

SAVE THESE INSTRUCTIONS

Intended Use

• This product is intended for temporarily heating residential rooms with

an effective area coverage of 120-160 ft

(11-15 m

• This product is intended for household use only. It is not intended for

commercial use.

• This product is intended to be used in dry indoor areas only.

• No liability will be accepted for damages resulting from improper use

or non-compliance with these instructions.

Product Description



DCB

Power on/off button

Handle

Decrease temperature button

Air vents

Increase temperature button

Rear caster wheels

Timer button

Power cord with plug

ECO mode button

Front caster wheels

Display

Cord hooks

Radiator ﬁns

Remote control

Before First Use

• Check the product for transport damages.

• Remove all the packing materials.

• Remove the protective strip from the remote control’s battery

compartment.

• Before connecting the product to the power supply, check that the

power supply voltage and current rating corresponds with the power

supply details shown on the product rating label.

DANGER

Risk of suffocation! Keep any packaging materials

awayfrom children – these materials are a potential source of danger,

e.g. suffocation.

Installing Caster Wheels

Step 1

Turn over the product and screw the front caster wheels (L) onto the

threads using the provided wing nuts.

Step 2

Attach the rear caster wheels (J) by using the U-shaped bolt and locking

it in between the last two radiator ﬁns.

Step 3

Turn the product back over once the caster wheels (L) has been installed

and before switching on the product.

Installing Cord Hook

Step 1

Insert the cord hook (M) into the air vents (I) matching up with the holes

for the screws.

Step 2

Tighten the screws until both cord hooks (M) are secure.

NOTICE

Cord hooks (M) can be installed on either side of the

product air vents (I).

Operation

Positioning the product

Place the product on a ﬂat and stable surface to avoid risk of tipping it

over.

Connecting

• Fully unwind the power cord (K) and connect the plug to a suitable

socket outlet.

• Once connected to the socket outlet, the display (F) shows . The

product is now on standby mode.

Switching on/off

• To switch on the product, press the power button (A) on the

control panel or remote control.

• The display (F) blinks for 3 seconds, then shows the current room

temperature. The product is operating on its lowest power setting.

• Press the power button (A) again to set the high power mode.

The display (F) shows and the product is operating on its highest

power setting.

• To switch off the product, press the power button (A) on the

control panel or remote control twice until the display (F) shows .

Temperature setting

• To adjust the temperature manually, press the increase temperature

panel or remote until the desired temperature has been reached.

• The maximum temperature setting is 80 °F (26.6 °C)

• The minimum temperature setting is 40 °F (4.4 °C)

NOTICE

The product gradually heats up once the desired power

temperature has been selected.

NOTICE

When the room temperature meets the setting

temperature, the product may continue to work for a while so that the

room can maintain its temperature.

Timer setting

• To set the timer, press the timer (D) button. The display (F) ﬂashes

and icon is shown on display (F).

• Immediately press or hold the timer (D) button again until the

desired length of time has been reached.

• The display (F) ﬂashes for 3 seconds and then starts to count down.

• The product automatically switches off once the timer countdown has

ﬁnished counting down. The icon goes off.

• To switch off the timer, press the timer (D) button until the display

(F) ﬂashes . The icon goes off.

NOTICE

The timer jumps one hour for each press of the button from

a minimum of 1 to a maximum of 24 hours.

Eco mode

• The power setting usage changes automatically depending on the

temperature of the room.

• Press the ECO mode button (E) to activate ECO mode.

Temperature (°F) Power setting

Below 65 High

65 - 75 Medium

75 or above Low

Cleaning and Maintenance

WARNING

Risk of electric shock! To prevent electric shock,

unplug the product before cleaning.

WARNING

Risk of electric shock! During cleaning do not

immerse the product in water or other liquids. Never hold the product

under running water.

Cleaning

• To clean the product, wipe with a soft, slightly moist cloth.

• Never use corrosive detergents, wire brushes, abrasive scourers,

metal or sharp utensils to clean the product.

Replacing remote control battery

2 3

• Remove the battery holder from the remote control (N).

• Replace the used battery with a new CR2025 3 V battery. The

positive pole (+) must be facing upwards.

• Slide the battery holder back in place.

NOTICE

Replace the battery if the range of the remote control

decreases noticeably or if the heater cannot be controlled via remote

control.

Storage

• Wrap the power cord (K) around the cord hooks (M).

• Store the product in its original packaging in a dry area. Keep away

from children and pets.

Maintenance

Any other servicing than mentioned in this manual should be performed

by a professional repair center.

Troubleshooting

Problem Solution

Unexpected crackling

sounds.

• This is a normal sound after starting up

the product. Once the heater heats up,

the crackling sound goes away.

Unexpected smell. • This is the result of dust or other debris

accumulating on the heating element.

This is normal during ﬁrst use and after

prolonged storage. Make sure the

product is placed in a well ventilated area.

Keep the product switched on, until the

smell disappears.

Heater shuts off

unexpectedly.

• Ensure the power cord is plugged into a

working socket outlet.

• Safety functions (overheating/tipped over)

may have been activated. Switch off the

heater to cool it down and restart.

Error code E0 appears

on display (F).

• Temperature sensor issue. The heating

function stops and all buttons are locked.

Contact a professional repair center.

Error code E1 appears

on display (F).

• Overheat shut-off activated. Wait at least

30 minutes to allow the product to cool

down, then restart.

• If the same error appears after product

has cooled down, refer to the instruction

below.

• Temperature sensor short-circuited. The

heating function stops and all buttons

are locked. Contact a professional repair

center.

Safety Functions

Tip-over switch

• The product automatically stops heating when it tips forward or

backward. The heating element and indicator light switches off.

• After placing the product into normal position, restart the product.

Battery Disposal

Do not dispose of used batteries with your household waste. Take

them to an appropriate disposal/collection site

Speciﬁcations

Model: B0828YJ33N

Voltage/frequency: 120V~, 60Hz

Power consumption: max. 1500W

Remote control battery: CR2025, 3 V

Dimensions (W x H x D):

approx. 13.1 x 9.8 x 26.3"

(33.5 x 25 x 67 cm)

Net weight: approx. 16.9 lbs (7.7 kg)

Feedback and Help

Love it? Hate it? Let us know with a customer review.

AmazonBasics is committed to delivering customer-driven products

that live up to your high standards. We encourage you to write a review

sharing your experiences with the product.

amazon.com/review/review‑your‑purchases#

amazon.com/gp/help/customer/contact‑us

amazon.com/AmazonBasics

V01-01/20

MADE IN CHINA

FABRIQUÉ EN CHINE

HECHO EN CHINA

AmazonBasics B0828YJ33N User manual

Brand: AmazonBasics

Model: B0828YJ33N

Category: Space heaters

Type: User manual

Download PDF

report

AmazonBasics B0828YJ33N User manual

AmazonBasics B0828YJ33N User manual

Related papers

Other documents