Motion Activated Sensor
MAS 100
User Manual
The Digital Door Viewer!
01- MAS100
Thank you for purchasing Motion Activated Sensor
for Brinno PeepHole Viewer!
Brinno MAS100 is an extension accessory for PeepHole Viewer
(PHV1330), it allows PHV1330 records images when a visitor come
close to your door. So even if you are not at home, you will know who
came to your door.
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as household
or general waste. It should be handed over to the applicable collection point for
the recycling of electrical and electronic equipment, or returned to the supplier for
disposal.
Internal / Supplied Batteries
This symbol on the battery indicates that the battery is to be collected separately.
This battery is designed for separate collection at an appropriate collection point.
Thank you for purchasing Brinno’s PeepHole Viewer
and accessories!
If you have any questions or problems setting up your Brinno PeepHole Viewer
and accessories, please contact the sales staff where you purchased our product
or email us at Brinno Incorporated directly
Please Visit our website
www.brinno.com
Package Contents
Before Installation
Motion Activated Sensor (MAS100)
1
Receiver (RFS100)
3
Screw
5
Holder
2
2 AA Batteries
4
1
5
2 3 4
1 2
1. Install 2 AA batteries on Motion Activated Sensor (MAS100).
2. Install receiver(RFS100) into extension port on PeepHole Viewer (PHV1330).
MAS100 -02
Installation
03- MAS100
Indoor IndoorOutdoor Outdoor
-a -b
1
3 3
2
1. Install Holder and tightening the screw.
2. Tear off the cover of double-sided glue.
3. Place your Motion Activated Sensor(MAS100) on our suggestion location:
a. Place on ceiling above the porch and face to ground.
b. Place above door, and adjust the Motion Activated Sensor angle, face to ground.
D
1*
A
1*
D
2*
D
1
: Detected distance: 5 meters
D
2
: Signal received distance: 5 meters
A
1
: Detected angle: 60°
Note
Model
Detect Angle
Detect Distance
Receiver Distance
Power Source
Accessories
Size
Weight
MAS 100
60˚
3~5 meters
5 meters
2 AA batteries
Holder, Recevier, 2 AA Batteries, User Manual
66(W) x 90(H) x 24(D) mm
56 g (without batteries)
MAS100 -04
Finished
Specications
Now, you already finished the installation,
for well working we suggest you to test
the detect of Motion Activated Sensor,
if it works on the location you placed,
then you can use screws to fix it on the
wall. If it doesn't work, please try to adjust
the detect angle or change to the other
location.
Red LED light: Detecting
Red LED ashing: Battery Low
LED
05- MAS100
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC ID: ZDX-MAS100
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Federal Communication Commission Interference Statement
301-0009-00
EN-A3
7F, No.75, Zhou Zi St., Taipei City 11493, Taiwan
Phone: 886-2-8751-0306 Fax: 886-2-8751-0549
E-mail: [email protected]
www.brinno.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Brinno KNS100 Owner's manual
-
-
-
Brinno MAS200D User manual
-
Brinno Command Center Software Operating instructions
-
-
-
-
Brinno SHC1000 User manual
-
