ANZZI FR-AZ473 User manual

ANZZI
Brand
ANZZI
Model
FR-AZ473
Category
Sanitary ware
Type
User manual
R
R
V2.0
ITEM:FR-AZ437* *
06/30/2022
ANZZI Deck Mount Tub Filler
06/30/2022
PRODUCT SIZE CHART
TOOLS
Wrench Adjustable Pliers Screwdriver flashlight
PG.1
[94mm]
10.6"
[268mm]
[40mm]
4.5"
[114.5mm]
2.2"
[55mm]
[47mm]
2.2"
[55mm]
[47mm]
[40mm]
2.2"
[55mm]
7.9"
[200mm]
6"
[154mm]
[475mm]
1/2"
1.4"
[35mm]
1.4"
[35mm]
1.6"
[40mm]
1.9"
[48mm]
[94mm]
10.6"
[268mm]
[40mm]
4.5"
[114.5mm]
2.2"
[55mm]
[47mm]
2.2"
[55mm]
[47mm]
[40mm]
2.2"
[55mm]
7.9"
[200mm]
6"
[154mm]
[475mm]
1/2"
1.4"
[35mm]
1.4"
[35mm]
1.6"
[40mm]
1.9"
[48mm]
PG.2
COMPONENT
Part Discription Qty
[15] Hand Shower
[01] Handle
[02] Cap
[04] Cover
[05] Retainer
[06] Cartridge
[07] Body
[08] O Ring
[09] Fixing Kit
[10] Hose
[11] Extension Hose
[13] Spout
[12] Shower Hose
[14] Screw
[16] Flow Restrictor
[17] Connector
[18] Shower Holder
[19] Check Valve
[20] Rubber Gasket
[21] Steel Gasket
[22] Lock Nut
[23] Connector
1
1
1
1
1
1
3
1
3
1
1
1
1
1
1
1
1
1
2
2
2
1
Before installation:
1. Please check that all components are present.
2. Ensure that all supply lines are free of debris with supply stops installed.
3. Ensure water pressure is between 20-125 PSI.
4. If you are having difficuties on installation, please contact a professional plumber.
[23]
[08]
[08]
[02]
[03]
[04]
[05]
[06]
[07]
[08]
[09]
[13]
[19]
[21]
[10]
[11]
[12]
[22]
[14]
[15]
[16]
[17]
[18]
[20]
[01]
INSTALLATION
STEP 2:
a. Slide the Rubber Gasket and Steel Gasket up
onto Body [07] from under the deck and secure
with Nuts.
b. Adjust the position of Body [07]. Hand tighten
the Nuts and tighten with wrench to secure
the Body [07].
STEP 3:
a. Adjust the Spout [13] so that the Rod at the right.
Tighten the Screw [14] to secure the Spout [13].
b. Remove Gasket [20], Steel Gasket [21],
Lock Nut [22] and Connector [23] from the shank.
c. Install Spout [13] through the deck hole in the middle.
Note: Make sure there is a O Ring [08] under the
Spout [13].
a. Slide the Gasket [20], Steel Gasket [21] up onto
Spout [13] from under the deck and secure with
Lock Nut [22].
b. Adjust the position of Spout [13]. Hand tighten the
Lock Nut [22] and tighten with screwdriver to secure
the Spout [13].
c. Install Connector [23] to the shank. Hand tighten it.
Unscrew the Connector [23] so that the outlet
pointed to the left. DO NOT unscrew the Connector
[23] over one turn, otherwise it may leaks.
STEP 1:
a. Remove Rubber Gasket, Steel Gasket and Nuts.
b. Install Body [07] through the deck hole on the left.
Note: Make sure there is a O Ring [08]. under the
Body [07].
12
PG.3
[23]
4
3
[20] [20]
[13]
[13] [13]
[22] [22]
[23]
ba
[23]
[21] [21]
Rod
[14]
[08]
[20]
[22]
[21]
HOT
COLD
[07]
Rubber Gasket
Rubber Gasket
Steel Gasket
Steel Gasket
Nuts
Nuts
[08]
HOT COLD
HOT COLD
PG.4
STEP 6:
a.Install the Shower [18] through the deck hole
on the right.
b.Slide the [20] and [21]
up onto Shower Holder [18] from under the deck
and secure with Lock Nut [22].
c. Adjust the position of Shower Holder [18]. Hand
tighten the Lock Nut [22] and tighten with
screwdriver to secure the Shower Holder [18].
Holder
Gasket Steel Gasket
STEP 7:
Connect Hand Shower [15] and Shower Hose [12].
Note: Make sure there is Washer between Connector
[17] and Shower Hose [12].
.....
STEP 8:
Slide the from above the
Shower Holder [18
Shower Hose [12]
].
STEP 5:
Remove [20], [21],
LOCK Nut [22] from the [18].
the Gasket Steel Gasket
Shower Holder
INSTALLATION
[18]
6
[18]
[08]
5
[20]
[22]
[21]
[20]
[22]
[21]
78
[17]
[12]
[15]
Washer
[15]
[18]
INSTALLATION
9
PG.5
a. Turn on the supply stop valves for 30s to 1 min to flush the debris in the supply lines. Turn off the supply
stop valves again.
b. Connect the Hot Labeled Hose [10] to the Hot Water Supply, Cold Labeled Hose [10] to the
Cold Water Supply. Tighten the Nuts with wrench. DO NOT OVER TIGHTEN.
c. Connect the third Hose [10] to the Connector [23]. Tighten the Nuts with wrench.
DO NOT OVER TIGHTEN.
d. Connect the Extension-Hose [11] to the shank of the Spout [13] from under the deck. Tighten the Nuts
with wrench. DO NOT OVER TIGHTEN.
e. Connect the Shower Hose [12] with the Extension-Hose [11] from under the deck. Tighten the Nuts
with wrench. DO NOT OVER TIGHTEN.
f. Turn on the supply stop valves and check connections for leaks. Retighten if necessary,
but DO NOT OVER TIGHTEN.
STEP 9:
H
C
H
C
[11]
[12]
[23]
[10]
HOT
COLD
Nut
Nut
Nut
Cold Water Supply
Hot Water Supply
CLEANING & MAINTENANCE
1. To preserve the finish on the metallic parts of your ANZZI faucet, apply non-abrasive wax,
such as car wax. Any cleaners should be rinsed off immediately.
2. Clean the flow regulator regularly for calcium build up or any blockage that reducing water flow.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

ANZZI FR-AZ473 User manual

ANZZI
Brand
ANZZI
Model
FR-AZ473
Category
Sanitary ware
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents