Coda 16 Amplifier User manual

Brand: Coda

Model: 16 Amplifier

Category: Audio amplifiers

Type: User manual

SAFETY PRECAUTIONS

INITIAL SETUP

INTRODUCTION

DETAILEDINSTALLATION

DESIGNPHILOSOPHY

TECHNICAL DATA

CARE&HANDLING

WARRANTY &DISCLAIMER

WARRANTY REGISTRATION

OPERATION MANUAL

AMPLIFIER 16.0

T E C H N O L O G I E SI N C .

BIAS INPUT

LEFT RIGHT

XLR/GN

RCA/YL

PRECISIONCLASS A AMPLIFIER

16.0

CODA TECHNOLOGIESINC.

16.0

G-300W/Y-5W

RANGERANGE

G-300W/Y-5W

CAUTION

WARNING

SAFETY PRECAUTIONS

CAUTION -

CAUTION: TOPREVENT ELECTRIC

SHOCK,DONOT REMOVECOVER.

NOUSERSERVICEABLEPARTS

INSIDE,REFERSERVICING TO

QUALIFIEDSERVICEPERSONNEL.

THISSYMBOL IS TO ALERT YOUOF

THEPRESENCEOFUNINSULATED

DANGEROUSVOLTAGEWITHIN THE

UNIT'SENCLOSURE THAT MAY BEOF

SUFFICIENT MAGNITUDE TO

CONSTITUTE A RISKOFELECTRIC

SHOCK.

THISSYMBOL ISINTENDED TO ALERT

YOUOF THEPRESENCEOF

IMPORTANT OPERATING AND

MAINTENANCEINSTRUCTIONSIN THE

LITERATURE ACCOMPANYING THE

UNIT.

WARNING:TOPREVENT FIREORSHOCKHAZARD,DO

NOT EXPOSE THISUNIT TORAINOR

MOISTURE. TO AVOIDELECTRICAL SHOCK,DO

NOT OPEN THEUNIT.REFERSERVICING TO

QUALIFIEDPERSONNEL.

Neverinstallorremovethepowercordfromthechassis

unlessithasbeendisconnectedfromthe ACpowersource

first.

Neverpullonthepowercordwhenremovingitfroman AC

powersource.Graspitbytheplug.

Donotleavethepowercordconnectedtoan ACpower

sourceunlessitisconnectedtotheunit.

Itisrecommendthatduringextendedperiodsofnon-use

thattheunitspowercordbeunpluggedfromits ACpower

source.

Routethe ACpowercordsothatitwillnotbedamagedor

walkedon.

Thankyouforpurchasingthe AMPLIFIER16.0.

Thisamplifierisaprecisiondevice,designedinanefforttoprovidethelistenerwith

unmatchedsoundqualitythroughsuperbdesignandconstruction.

Althoughitsoperationisfairlysimple,inordertooperateyouramplifierproperlyandto

realizeallofthecapabilitiesoftheamplifierwerecommendthatyoureadthisentiremanual

carefully.

INTRODUCTION 2

INITIAL SETUP 3

Thediagrambelowshowsthedefaultconnectionsnecessarytooperatethe16.0asastereo

amplifier. Thisisthesimplestandmostcommonmodeofoperation,andthequickestwayto

getstarted.Oncetheseconnectionsaremadeyoucanturnthepowerswitchon,enablethe

biasfromthefrontpanelandstartlisteningtoyouramplifier.

Forsimplicitythisdiagramshowsanaudioconfigurationusingbalancedinterconnects. This

isthedefaultinputmodeoftheamplifier.Unbalancedoperationrequiresthatyousetthe

appropriateinputmodeasdetailedonpage5.

WARNING:PleaseensurethatthepowerswitchisturnedOFFwhileyouareconnecting

theamplifier.Connectingordisconnectingcableswhiletheamplifierispoweredoncould

causedamagetoyourspeakers.

NOTE:Ensurethatthemodeswitchlocatedbetweentheinputjacksontherearofthe

amplifierissettothestereopositionfornormaloperation.Bridgedoperationisexplainedon

page7.

Stereo AmplifierConfiguration

LEFT SPEAKER RIGHT SPEAKER

PREAMPLIFIER

AMPLIFIER16.0

FORCONTINUEDPROTECTIONAGAINST

SHOCKORFIREHAZARD,DONOTEXPOSE

THISUNITTORAINORMOISTURE.

ACLINEINPUT

SEESERIALTAGFOR

POWERREQUIREMENTS

UNBALANCEDINPUT

RIGHTLEFT

COMPACTDISC

RIGHTLEFT

TUNER

RIGHTLEFT

VIDEO

RIGHTLEFT

MONITOR

RIGHTLEFTRIGHTLEFT

IN OUT

PROCESSOR

RIGHTLEFTRIGHTLEFT

IN OUT

VIDEO

RIGHTLEFT

UNBALANCEDOUTPUT

RIGHTLEFT

DO NOT CONNECT AMPLIFIER OUTPUT

TERMINALS TOGETHER. CONNECT

AMPLIFIER OUTPUT TERMINALS ONLYTO

SPEAKERS.

FOR CONTINUED PROTECTION AGAINST

SHOCKORFIRE:

REPLACE FUSE WITH SAME TYPE AND

RATING. DO NOT EXPOSE THIS UNIT TO

RAINORMOISTURE

SEESERIALTAGFORPOWERREQUIREMENTS.

REMOVEPOWERCORDBEFORECHANGINGFUSEORLINEVOLTAGE.

READ THEBRIDGINGSECTIONOF THEOPERATINGMANUAL ORCONTACTYOURCODA AUTHORIZED

ACLINEINPUT MAINPOWER FUSE/VOLTAGESELECTOR

DEALER TOSET THEBRIDGINGSWITCHES

BRIDGEDMODE

16AMP

8AMP

UNBALANCED

BRIDGED

INPUTS

BALANCED

INPUTS

UNBALANCED

PUSH PUSH

230

DETAILED INSTALLATION 4

I.Connections

Theconnectorsandcontrolsareclearlymarkedonthebackpaneloftheamplifier.Notethe

correctleftorrightchannelorientation. Thefunctionandchannelmarkingsontherearpanel

correspondtothefrompanelcontrolsandtheirsignalpaths.

1. Theunbalancedandbalancedinputsshouldbeattachedtotheappropriateunbalanced

andbalancedoutputsofapreamplifiereitherdirectlyorthroughacrossoverorprocessor,as

appropriatetotheapplication.

2.Theleftoutputandrightoutputshouldbeattachedtotheleftandrightspeakers

respectively.

WARNING:PleaseensurethatthepowerswitchisturnedOFFwhileyouareconnecting

theamplifier.Connectingordisconnectingcableswhiletheamplifierispoweredoncould

causedamagetoyourspeakers.

3. The AClineinputshouldbeconnectedtoan ACoutletwiththepowercableprovidedwith

theamplifier.

4. Thefuseandvoltageselectorunithousesa5x20mmslow-blowfuseandavoltage

selectorcartridge.Ensurethatthevoltage,visiblethroughasmallwindownexttothe AC

input,issettotheappropriatevoltageforyourcountry.Whenchangingvoltages,ensurethat

thepowercableisdisconnectedfromtheamplifier.

NOTE:Ifthefuseinyouramplifierblows,contactaCodadealerorcallCodadirectlybefore

attemptingtousetheamplifieragain.

5. Thepowerswitchcanusuallybeleftonwhentheamplifierisfunctioningcorrectly.Withthe

biasdisabledtheamplifierwilldrawnegligiblecurrentandcanthusbeleftin “standby”

indefinitely.

DONOT CONNECT AMPLIFIEROUTPUT

SHOCKORFIRE:

REMOVEPOWERCORDBEFORECHANGINGFUSEORLINEVOLTAGE.

READ THEBRIDGINGSECTIONOF THEOPERATINGMANUAL ORCONTACT YOURCODA AUTHORIZED

ACLINEINPUT MAINPOWER FUSE/VOLTAGESELECTOR

DEALER TOSET THEBRIDGINGSWITCHES

BRIDGEDMODE

16 AMP

8 AMP

UNBALANCED

BRIDGED

INPUT

INPUTS

BALANCED

INPUTS

UNBALANCED

PUSH PUSH

230

FORCONTINUEDPROTECTION AGAINST

REPLACEFUSEWITHSAME TYPE AND

RATING.DONOT EXPOSE THISUNIT TO

RAINORMOISTURE.

TERMINALS TOGETHER.CONNECT

AMPLIFIEROUTPUT TERMINALSONLY TO

SPEAKERS.

1 243 3

BIAS INPUT

LEFT RIGHT

XLR/GN

RCA/YL

PRECISIONCLASS A AMPLIFIER

16.0

CODA TECHNOLOGIESINC.

DETAILED INSTALLATION 5

II.FrontPanelControlFunctionsandIndicators

1. Thebiasbuttonenablesthebias,effectively “turningon”theamplifier’scomponents,and

opensshuntingrelaysthatmutetheinput.

2. Theinputselectorbuttonswitchesbetweenthebalancedandunbalancedinputs.

3. TheseLEDs,whenlit,indicatethatthebiasisenabledandmutingisoff.

4. ThistwocolorLEDindicatesthatthemainpowerison.Whenitisgreenthebalanced

inputsareinuse.Whenitisyellowtheunbalancedinputsareinuse.

Note:Ifapowerinterruptionoccurstothesystemtheamplifierwillpoweronwiththebias

off.Pressthebiasbuttontoresumeuseoftheamplifier.

DETAILED INSTALLATION 6

The16.0normallyoperatesinstereomode,providingamaximumoutputpowerof150watts

Class AB(intoan8-ohmload)perchannel.Inbridgedmode,bothchannelsactasone

amplifierprovidingamaximumoutputpower600watts.Forextremelyhigh-powermulti-

channelaudioapplications,multiple16.0amplifierscanbeusedinplaceofonestereo

amplifier.

Toconfiguretheamplifierforbridgedmodeoperationyoumustenablethebridgingswitches

insidetheamplifier.Usea5/64”hexdrivertoremovethetwelvescrewsfromthetopofthe

amplifierandremovethetopcover. Thebridgingswitchesaremountedonacircuitboard

attachedtotheaudioinputjacksinsidetheamplifier. Thediagrambelowshowsthecircuit

board. Theredslideswitchesbelowthearrowsarethebridgingswitches. Thearrowsshow

thedirectiontosettheswitchestoenablebridging.Reversetheswitchpositionstoenable

normalstereooperation.

WARNING:Disconnecttheamplifier’spowercordfromthe ACsupplyandsetthepower

switchtoOFFbeforeadjustingthemodeswitchorconnectingordisconnectinganycables

toavoidpotentialdamagetoyourspeakersandpersonalinjuryduetohighinternal

voltages.

III.BRIDGEDSETUP

Inbridgedmodeonlyoneaudioinputisused.Nootherinputshouldbeconnected,andthe

bridgedmodeinputmustbeabalancedsignalconnectedtotheXLRreceptaclelabeled

BRIDGEDINPUT.Bridgedmodewillnotoperatecorrectlywithaninputadaptedfroman

unbalancedsignal.ConnectingtheinputsignaltothereceptaclenotlabeledBRIDGED

INPUT willcausenodamage,butwillcausethespeakerterminalpolaritiestoreverse,with

theterminallabeledpositivebecominggroundandtheterminallabeledgroundbecoming

positive.

Theamplifier’sspeakerterminalsarereconfiguredinbridgemode. Theleftchannelpositive

terminalbecomesthemonauralnegativeterminalandtherightchannelpositiveterminal

becomesthemonauralpositiveterminal.

Seethenextpageforadiagramofastereoamplifierconfigurationusingtwobridgedmode

16.0amplifiers.Speakerterminalsinthediagramaremarkedwiththeirbridgedmode

polarities.

DO NOT CONNECT AMPLIFIER OUTPUT

TERMINALS TOGETHER. CONNECT

AMPLIFIER OUTPUT TERMINALS ONLYTO

SPEAKERS.

FOR CONTINUEDPROTECTION AGAINST

SHOCKORFIRE:

REPLACE FUSE WITH SAME TYPE AND

RATING. DO NOT EXPOSE THIS UNIT TO

RAINORMOISTURE

SEESERIALTAGFORPOWERREQUIREMENTS.

REMOVEPOWERCORDBEFORECHANGINGFUSEORLINEVOLTAGE.

ACLINEINPUT MAINPOWER FUSE/VOLTAGESELECTOR

READ THEBRIDGINGSECTIONOF THEOPERATINGMANUAL ORCONTACTYOURCODA AUTHORIZED

DEALER TOSET THEBRIDGINGSWITCHES

BRIDGEDMODE

16AMP

8AMP

UNBALANCED

BRIDGED

INPUT

INPUTS

BALANCED

INPUTS

UNBALANCED

PUSH PUSH

230

DO NOT CONNECT AMPLIFIER OUTPUT

TERMINALS TOGETHER. CONNECT

AMPLIFIER OUTPUT TERMINALS ONLYTO

SPEAKERS.

FOR CONTINUEDPROTECTION AGAINST

SHOCKORFIRE:

REPLACE FUSE WITH SAME TYPE AND

RATING. DO NOT EXPOSE THIS UNIT TO

RAINORMOISTURE

SEESERIALTAGFORPOWERREQUIREMENTS.

REMOVEPOWERCORDBEFORECHANGINGFUSEORLINEVOLTAGE.

ACLINEINPUT MAINPOWER FUSE/VOLTAGESELECTOR

READ THEBRIDGINGSECTIONOF THEOPERATINGMANUAL ORCONTACTYOURCODA AUTHORIZED

DEALER TOSET THEBRIDGINGSWITCHES

BRIDGEDMODE

16AMP

8AMP

UNBALANCED

BRIDGED

INPUT

INPUTS

BALANCED

INPUTS

UNBALANCED

PUSH PUSH

230

RIGHT SPEAKER

LEFT SPEAKER

PREAMPLIFIER

FORCONTINUEDPROTECTIONAGAINST

SHOCKORFIREHAZARD,DONOTEXPOSE

THISUNITTORAINORMOISTURE.

ACLINEINPUT

SEESERIALT AGFOR

POWERREQUIREMENTS

UNBALANCEDINPUT

RIGHTLEFT

COMPACTDISC

RIGHTLEFT

TUNER

RIGHTLEFT

VIDEO

RIGHTLEFT

MONITOR

RIGHTLEFTRIGHTLEFT

IN OUT

PROCESSOR

RIGHTLEFTRIGHTLEFT

IN OUT

VIDEO

RIGHTLEFT

UNBALANCEDOUTPUT

RIGHTLEFT

DETAILED INSTALLATION 7

IV.BRIDGEDSETUP DIAGRAM

REMOTEOPERATION

The16.0canbeoperatedbyremotecontrol. TheMX-450LearningRemoteis

optional.ForinstructionsonusingtheMX-450itselfseetheonscreenmanual

includedintheremote.

DETAILEDINSTALLATION

DETAILED INSTALLATION 9

Thelightbehindthelogoonthefrontpanelofyouramplifiercanbeenabledanddisabledby

settinginternalswitchesinsidetheamplifier’schassis.Changingthissettingrequires

removingtheamplifier’stopcover.

ThelightiscontrolledbytwosmallswitcheswithredsliderslocatedonthePCBattachedto

thebacksideofthefaceplate.Viewingfromtherearoftheamplifier,withthecoverremoved,

theswitcheswillbeatthetopofthePCBasshownbelow.

WARNING:Disconnecttheamplifier’spowercordfromthe ACsupplyandsetthepower

switchtoOFFbeforemakinganyinternaladjustmentstoavoidpersonalinjuryduetohigh

internalvoltages.

LOGOLIGHT CONTROL

Toenablethelightonlywhenthebiasis

turnedon:

Slidetheleftswitchtotheleftorright,and

therightswitchtotheleft.

Toenablethelightatalltimes:

Slidetheleftswitchtotheleft,andtheright

switchtotheright.

Todisablethelightatalltimes:

Slidetheleftswitchtotheright,andthe

rightswitchtotheright.

DESIGNPHILOSOPHY

I.DesignPhilosophyand Approach

Thesubtletyofthedesignprocessatthislevelofperformancemakesitimpossibletoeasily

explainalloftheadvantagesinherentinthe16.0.However,wepresenthereanoverviewto

giveyouanunderstandingofsomeofitsuniquefeaturesandanideaofthelistening

experienceyoucanexpect.Oftenaparticulartechniquehasnumerousunrelatedadvantages

andpossibilities.Wemakeeveryefforttoexploittheseadvantageswiththefinalresultbeing

anamplifierthatperformsbetterthanthesumofitsindividualfeaturessuggest.

ThetopologyandcomponentselectionisbuiltonthefoundationestablishedbytheCoda

System100.Balancedinterconnectionsareprovidedtotakeadvantageoftheirgreaternoise

rejection.Differentialvoltagegainthroughoutprovidesexceptionalrejectionofexternalnoise

andcontributestotheinherentDCstabilityofthecircuit. Thisallowsdirectcouplingwithout

servocircuitry. Theunitalsousesoutputfollowersoperatingwithoutfeedback.

Excellenthighfrequencydesignensureslinearoperationathighspeed,andtranslatesintoa

sonicreproductionwhichisextremelytransparentincharacter. Thepowersupplytakesa

verydirectapproachtohighperformance. First,topqualitytoridaltransformersandover

280,000uFofcapacitancewithverylowESRandinductanceareused.Foroptimum

performanceandreliabilityallcircuitryremainscontinuouslypowered.

Thespecificationsareconsistentwithwhatwouldbeexpectedinahighcurrentamplifier

design.Inthisdesign,however,anunusualdegreeofattentionhasbeenpaidtosonically

meaningfulparameters.

Forexample,thecurrentstageiscapableofproducingpeakcurrentsinexcessof100

Ampereswithadegreeoflinearityandspeedunmatchedbyotherdesignsproducingonlya

fractionofthiscurrent. Thisisachievedbytheimplementationofseveraldistinctcircuit

features.

Extremelywidebandwidthtransistorsareusedintheoutputstageinsteadoftheusual TO3

devicesusedinotheroutputdesigns.Eachchanneluses28individualoutputtransistorswith

acombinedpowerratingof1500Wattsand120 Ampereswithabandwidthof50Mhz.

The16.0usesbiasvoltagesandcomponentvalueswhichhavebeenspecificallyselectedto

produceaprecisiontransitionwithnoabruptchangesindistortionoroutputimpedance. This

“PrecisionBias”techniqueyieldsseamlessperformanceregardlessofthecomplexityofthe

loadimpedanceandisparticularlyeffectiveateliminatingIMdistortionwhichoftenoccursin

theseinstances.

DESIGNPHILOSOPHY

I.DesignPhilosophyand Approach(continued)

Tomaintain “PrecisionBias”requiresanadvancedbiascircuitthatmusthaveaveryhigh

degreeofstabilityunderawiderangeoftemperaturesandloadconditions.Mostamplifier

biasnetworksareofsuchhighimpedanceandpoorthermalregulationthatattheextremes

ofoperation,biascurrentsareineffectivelycontrolled. Advancedtrackingtechniquesusedin

the16.0resultinabsolutecontrolofbiascurrentsunderallconditions.

Themainpowersupplyoftheamplifierconsistsofa3000VA transformerwithindependent

rectifierstoisolatethechannelsfromoneanother.280,000uFoftotalcapacitanceprovide

effectivefilteringofall ACripple.

Theseattributesresultinanamplifierofsuchextremelinearityandbandwidththatnooverall

feedbackcorrectionisrequiredorused.Oneadvantageofthisisahighdegreeofimmunity

frominteractionswithloadsorcablesandasuperiortransientresponse. Anextremelylow

nonreactiveoutputimpedanceismaintainedwellbeyond20,000Hz.theresultinguniform

dampingfactorisnotcommonlyfoundinotherdesigns.

Thechassisofthe16.0isconstructedofmachinedaluminummilledtoveryclosetolerances

yieldingtheseamlessappearancecharacteristicofpreviousproductsfromCoda. Aswithall

high-poweramplifiers,heatdissipationisimportant. The16.0usessixmassivealuminum

heatsinkswithoutfansforefficient,noiselessandcleanthermalrelief. Thethermalcoefficient

ofthe16.0heatsinksisoneofthelowestandmosteffectiveintheaudioindustry.

DESIGNPHILOSOPHY

II.MaterialQuality

Theamplifier’schassisismadefrommachinedaluminum. Allexteriormetalpartsare

anodizedorpowdercoatedfordurability.

Printedcircuitboardsarefiberglassepoxywithgoldplatingoveratin/nickelbarrier. Thegold

layerwillnotcorrode,whilethebarrierlayerpreventsthegoldfrommigratingtothelower

copperlayer.

Allresistorsareprecisionmetalfilm;1%tolerancefor1/4-wattand5%tolerancefor1-watt.

Capacitorshavebeeneliminatedwhereverpossible.Noelectrolyticcapacitorsareused

exceptinthepowersupply,whereseveralhigh-capacitanceelectrolyticsprovideoutstanding

filteringofthesupplyoutput.

Allsemiconductordevicesareofveryhighgrade.Voltagegainisaccomplishedwithan

extremelyhigh-quality,matcheddualFET,chosenforit’sexceptionallylownoise

characteristics.

Allaudioinputandoutputconnectorcontactsaregold-plated,andXLRreceptaclesare

manufacturedbyNeutrikofSwitzerland.Wireisusedaslittleaspossibleinthesignalpath-

onlytoconnecttheRCA jacksandspeakerterminalstothecircuitboard-andwhatisusedis

141-strandsilver-platedcopperwithsiliconeinsulation.

TECHNICAL DATA

STEREO

RatedPower: 150Wattsclass AB(100Wattsclass A)@8Ohms,

300Wattsclass AB@4Ohms

FrequencyResponse: DCto-3dB@100kHz

Distortion: <.02percentfrom10Hzto20kHz@ratedpower

Gain: 26dB

MaximumCurrent: >100 Amperespeakperchannel

Noise: -120dBreferencedtoratedoutput

InputImpedance: 50kOhmsunbalanced/10kOhmsbalanced

OutputImpedance: .03Ohmsfrom20Hzto20kHz

BRIDGEDMONO

RatedPower: 600Wattsclass AB@8Ohms

FrequencyResponse: DCto-3dB@100kHz

Distortion: <.02percentfrom10Hzto20kHz@ratedpower

Gain: 32dB

MaximumCurrent: >100 Amperespeak

Noise: -130dBreferencedtoratedoutput

InputImpedance: N/A unbalanced/10kOhmsbalanced

OutputImpedance: .06Ohmsfrom20Hzto20kHz

POWERSUPPLY

TransformerRating: 3kVA

PowerFiltering: 280,000 F

DIMENSIONS

Height: 7"Faceplate,7.75"Overall

Width: 18”Overall

Depth: 19"Overall

Weight: 110lbs.,115lbs.Shipping

Powerrequirement: 1KWattsmaximumatratedpower

1200Wattsclass AB@4Ohms

Transformer Type: Multi-tap,multi-windingtoroidal

CARE&HANDLING

Theinterioroftheunitrequiresnospecialcare.Ifitbecomesnecessarytocleantheexterior,

asimpledustingmaybeallthatisrequired.Ifacleanerisnecessary,anydilutecommercial

ammoniabasedproductwillbeappropriate.NEVERuseanyabrasiverags,cleanersor

chemicalsolventsonCodaproducts.

Whenhandlingtheunit,takecarenottomarthealuminum. Aluminumisamediumhardness

metalandcanbescratchedbythehardertoolsteels.

Avoidexposingtheunittodirectsunlight,andkeepitawayfromsourcesofintenseheat.

Donotthrowawaythecartonorassociatedpackingmaterial. Theyareidealifyouneedto

packtheunitformovingandintheunlikelyeventthatservicingisneeded,theywillbe

necessaryforsafeshipment.

Besuretoprovideadequateinsurancewhenshipping.

WARRANTY &DISCLAIMER

I.Warranty- Anyfailureoftheamplifier,hereafterknownastheproductororiginalproduct,to

operateortomeetspecifications,applicableattimeofmanufacture,duetoamanufacturing

defectorcomponentfailure,willbecorrectedbyCoda Technologieswithoutchargeforparts

orlabor,foraperiodoftenyearsfromdateoforiginalpurchase.Coda Technologieswill

provideforsurfacetransportationtoandfromthefactoryforaperiodofoneyearfromdateof

originalpurchase.

II.Procedure-IftheproductshouldrequireserviceunderwarrantycontactCoda

Technologiesatthelocationonthebackcoverofthismanualforshippinginstructions.

ProductspurchasedoutsideoftheUnitedStateswillbecoveredbythewarrantyconditions

extendedbytheimportingdistributorwhichmaydifferfromthosegivenabove.

III.ExclusionofCoverage-Coda Technologiesisnotobligatedtoservicetheproductin

certainconditions,asaccordingtothefollowingsubsections.

a. Theproducthasbeendamagedthrough:

i.operationnotinaccordancewiththeinstructionsinthismanual

ii.abuse,tampering,modificationoraccident

iii.serialnumberdefacement

c. TheproducthasbeentransportedoutsideoftheUnitedStatesof America.

IntheseconditionsanyservicewillbemadeatCoda Technologiessoleoption.

IV. TotalLossandReplacement-Iftheproductissubmittedforserviceduetoasevere

malfunctionwhichhascauseddamagesufficientenoughtomakearepairattemptinfeasible,

theproductwillbereplacedwithanotherunitofequalorsuperiorspecifications.Coda

Technologiesproductlineisfrequentlyupdatedandchanged,andthespecificmodeland

versionoftheoriginalproductmaybediscontinuedatanytimewithoutnotice.Inthiscaseno

guaranteesaremadethatthereplacementunitwillbevisuallysimilartotheoriginalproduct.

V.SubjectiveDifferences-Noguaranteeismadethattheproductwillperformtoany

specificationsthatcannotbemeasuredandconfirmedwithprecisionaudioanalysis

equipment.Coda Technologiesisonlyobligatedtomakerepairswhichwillbringtheproduct

intocompliancewiththespecificationsstatedinthismanual.

VI.UnnecessaryService-Inallconditions,iftheproductissubmittedforserviceandfound

tobeoperatedwithoutfaultandwithinspecifications,shippingchargeswillbebilledtothe

customer.

Thiswarrantygivesyouspecificlegalrights. Youmayhaveotherrightswhichvaryfromstate

tostate.

Disclaimer-Coda Technologiescannotbeheldresponsibleforanydamagecausedbytheir

products,includingbutnotlimitedto:

a.DamagetospeakerscausedbyfailureofaCoda Technologiesproducttomute

ordisableitselfasexpectedordescribedinitsmanual.

b.DamagecausedbyconnectingaloadtoaCoda Technologiesproducthaving

animproperimpedanceasdescribedintheproductsmanual.

c.Damagecausedbydefectsindesign,constructionorcomponentquality.

Theproducthasbeentransferredtoathirdparty.Inthiscasethewarranty

Iisvalidfor5yearsfromdateofmanufactureasdeterminedfromtheserialnumber

WARRANTY REGISTRATION

FillinthisregistrationsheetandfaxormailittoCoda Technologiestoensureyouareinour

warrantysystem. Thiswillfacilitatewarrantyserviceshoulditbecomenecessary.

Itisrecommendedthatyouretainacopyofthisformforyourownrecords.Coda

Technologies’addressandfaxnumberarelocatedonthebackofthismanual.

MODEL DESIGNATION:

SERIAL NUMBER:

DATEOFPURCHASE:

PLACEOFPURCHASE

OWNERINFORMATION

NOTES:

Name:

Address:

City: State: Zip:

Phone:

Name:

Address:

City: State: Zip:

Phone:

WARRANTY REGISTRATION

FillinthisregistrationsheetandfaxormailittoCoda Technologiestoensureyouareinour

warrantysystem. Thiswillfacilitatewarrantyserviceshoulditbecomenecessary.

Itisrecommendedthatyouretainacopyofthisformforyourownrecords.Coda

Technologies’addressandfaxnumberarelocatedonthebackofthismanual.

MODEL DESIGNATION:

SERIAL NUMBER:

DATEOFPURCHASE:

PLACEOFPURCHASE

OWNERINFORMATION

NOTES:

Name:

Address:

City: State: Zip:

Phone:

Name:

Address:

City: State: Zip:

Phone:

7850CUCAMONGA AVENUE#34

SACRAMENTO,CA 95826USA

phone

onthewebat

emailusat

fax

+01916.383.3653 +01916.455.3653

CODA.CC

[email protected]

Coda 16 Amplifier User manual

Brand: Coda

Model: 16 Amplifier

Category: Audio amplifiers

Type: User manual

Download PDF

report

Coda 16 Amplifier User manual

Coda 16 Amplifier User manual

Related papers

Other documents