SECO-LARM ENFORCER EV-Y1501-AMWQ Owner's manual

Brand: SECO-LARM

Model: ENFORCER EV-Y1501-AMWQ

Category: Security cameras

Type: Owner's manual

This manual is also suitable for

4-in-1 HD TVI, CVI, AHD, Analog

Bullet Cameras

Manual

 Select between multiple formats:

TVI, CVI, AHD, and Analog

 5MP Resolution

 ICR Module

 Joystick OSD Control

 DNR (Digital Noise Reduction)

 D-WDR (Digital Wide Dynamic Range)

 Rugged, weatherproof (IP66) construction

 Cables concealed in bracket to

prevent tampering

Features:

Model # Lens Resolution Voltage Style Color

EV-Y1501-A2WQ 2.8mm 5MP 12VDC Bullet White

EV-Y1501-AMWQ 2.8~12mm 5MP 12VDC Bullet White

EV-Y1501-

2WQ shown

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Cameras

2 SECO-LARM U.S.A., Inc.

Specifications:

Model EV-Y1501-A2WQ EV-Y1501-AMWQ

Type Fixed Bullet Camera Varifocal Bullet Camera

Formats TVI (Default) / CVI / AHD / Analog (CVBS)

CMOS

2.7

" 5MP CMOS

Resolution (HD) 2592x1944

3DNR No

2DNR Yes

D-WDR Yes

OSD (On-Screen Display) Yes

Cable OSD control Yes

Megapixels 5MP

Lens 2.8mm ICR 2.8~12mm ICR

Viewing angle 121° 38°~138°

# of IR LEDs 18 (SMT) 30 (SMT)

IR Range Up to 50ft (20m) Up to 115ft (35m)

FPS 20FPS

F Stop F2.0

Minimum

illumination

IR On 0Lux

IR Off 0.05Lux

S/N Ratio 35dB

Shutter control Auto

Gain control Auto

Operating voltage 12VDC

Current draw

IR On 320mA 350mA

IR Off

80mA

IP Rating IP66

Operating temperature -22°~131° F (-30°~55° C)

Dimensions

" x 2

(140x69x71 mm)

" x 3" x 3

(240x77x84 mm)

Weight 12.3-oz (349g) 1-lb 12.4-oz (805g)

Dimensions:

1x Bullet camera 3x Screws 3x Screw anchors 1x Manual

1x Mounting template 1x Hex wrench 1x Power balun 1x OSD Manual

Parts List:

EV-

1501-AMWQ: EV-

1501-A2WQ:

" (240mm)

" (150mm)

" (140mm)

" (126mm)

(

69mm

)

(77mm)

(58mm)

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Cameras

SECO-LARM U.S.A., Inc. 3

Overview:

Installation:

Important: Do not cut any wires as the warranty will be voided.

1. Run a 12VDC power supply wire and a video cable

with a male BNC connector to the wall or ceiling

where the camera is to be mounted.

2. Temporarily connect the camera to the 12VDC

power supply.

3. Temporarily connect the camera’s female BNC

connector to the video cable’s male BNC connector.

4. While watching the monitor, hold the camera against

the wall or ceiling by hand where it is to be mounted,

then turn the camera until it is certain that this

mounting location is correct.

djust the zoom and focus to desired settings. See

"Zoom and Focus Adjustment" (EV-Y1501-AMWQ

only).

6. Use the OSD controller's joystick to adjust the camera

settings. See "OSD Controller Settings". (For more

information, see separate OSD manual).

7. Use a pencil and the included mounting template

sticker to mark the mounting location. Disconnect the

12VDC power supply and video cable.

8. Mount the camera mounting base to the wall using the

included mounting screws.

OSD Controller Settings:

To set format via the OSD controller, move the

controller in the direction of the desired setting,

hold for 5 seconds, and release when the

camera restarts.

See chart below.

Direction Format Setting

Down CVBS/Analog

Left TVI

Right CVI

DC Jac

Female BNC

Connector

OSD controller

Sunshield screw Sunshield

Mounting arm

adjustment screw

Camera angle

adjustment screw

Mounting

screws

EV-Y1501-

MWQ shown above.

Zoom & Focus Adjustment*:

To adjust the Zoom and Focus, open the Zoom/Focus compartment

located on the bottom of the camera. Once within the compartment,

use a flathead screwdriver to loosen the Zoom and Focus screws to

allow for adjustment.

Focus

To focus in on close objects, push

the focus screw right towards "N".

To focus out on far objects, push

the screw right towards "F".

Zoom

To zoom in, push the zoom screw

left towards "T". To zoom out, push the

screw right towards "W".

1. Use the camera within the given temperature

and voltage limits.

2. Do not point the camera at the sun.

3. Do not subject the camera to strong vibrations.

4. Do not mount the camera in areas exposed to radiation,

strong magnetic fields, or strong electrical signals.

Before Starting:

Mounting base

*EV-Y1501-

MWQ only.

(Continued next page)

Zoom

Focus

To adjust the camera angle and positioning,

loosen the camera angle adjustment screw

and mounting arm adjustment screw.

Rotate the camera and position the

mounting arm in the desired position and

retighten the screws.

Camera arm position:

Camera Angle and Positioning:

Mounting arm

adjustment screw

Camera angle:

Camera angle

adjustment screw

N F

Base

Front

BNC

Connector

Camera

NOTE: Do not press joystick in when setting different modes.

Zoom and focus

compartment

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Cameras

4 SECO-LARM U.S.A., Inc.

The screen is blank.

 Check that the camera is powered up.

 Check that the power supply's polarity is correct.

 Check that the monitor is powered up.

 Check that the video cable connecting the camera to the monitor is

connected properly.

The screen image is dim.

 Clean the lens using a soft, clean cloth.

 Check that the light source is adequate.

The screen image has poor contrast.

 Adjust the monitor's contrast knob.

 Change the position of the camera.

The screen image flickers.

 Change the position of the camera, check cables and format setting

The screen image is distorted.

 Change the position of the camera, check cables and format setting

The camera case is hot.

 Check that the correct power supply is in use.

Installation (continued):

PICRN3

MI_EV-Y1501-

xWQ_191206.doc

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,

state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be

held responsible for the use of this product in violation of any current laws or statutes.

SECO-LARM

U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com

Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal

service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or

replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if

damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,

improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment

is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of

SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s

option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property

damage of any kind to the purchaser or anyone else.

Troubleshooting:

WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric

shock. Do not open the case of this device, as there are no user-serviceable components inside.

Do not cut any wires as the warranty will be voided.

9. Reconnect the 12VDC power supply and video cable.

10. Turn the monitor on and confirm the camera is sending the proper video signal.

11. Adjust the camera to the desired angle and position. See "Camera Angle and Positioning" for more information.

12. Do a final test of the video camera and monitor.

FCC COMPLIANCE STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the

device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure

uirements and void user’s authorit

to o

erate the device.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM

reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks

rights reserved.

SECO-LARM ENFORCER EV-Y1501-AMWQ Owner's manual

Brand: SECO-LARM

Model: ENFORCER EV-Y1501-AMWQ

Category: Security cameras

Type: Owner's manual

This manual is also suitable for

Download PDF

report

SECO-LARM ENFORCER EV-Y1501-AMWQ Owner's manual

This manual is also suitable for

SECO-LARM ENFORCER EV-Y1501-AMWQ Owner's manual

Related papers

Other documents