Nice Apollo 936 Control Board for 1550 / 1650 Gate Openers User guide

936 Control Board for 1550 / 1650 Gate Openers
Nice Apollo
Brand
Nice Apollo
Model
936 Control Board for 1550 / 1650 Gate Openers
Type
User guide

This manual is also suitable for

Nice Apollo 936 Control Board for 1550 / 1650 Gate Openers provides advanced control and customization options for your swing gate operator. With its intuitive interface and comprehensive features, you can easily set up and adjust various parameters to ensure smooth, safe, and reliable operation of your gate system. From learning procedures and primary settings to force adjustment, slowdown control, and auto-close configuration, the 936 Control Board offers a user-friendly experience and enhances the performance of your gate opener.

Nice Apollo 936 Control Board for 1550 / 1650 Gate Openers provides advanced control and customization options for your swing gate operator. With its intuitive interface and comprehensive features, you can easily set up and adjust various parameters to ensure smooth, safe, and reliable operation of your gate system. From learning procedures and primary settings to force adjustment, slowdown control, and auto-close configuration, the 936 Control Board offers a user-friendly experience and enhances the performance of your gate opener.

TECHNICAL BULLETIN
P/N 10059799
936 QUICK START GUIDE
Publish Date:
March 2019
LEARN PROCEDURE
1. Connect battery power, monitored entrapment device(s)
(photo eye), and motor to board as outlined in manual for
particular operator you are using. For dual systems, connect
only one motor at this time. Connect other accessories after
basic system operation is conrmed.
2. Lr should be ashing. If not, hold RESET command until Fd
is displayed - then Lr will begin ashing.
3. Run motor by holding down either Open or Close buttons on
board. If motor runs opposite of what it should be, reverse
motor wires (red/black) and re-check travel direction.
4. Put operator in closed position and adjust appropriate limit
until Close LED limit indicator above the motor is connected
comes on. If the Open Limit LED is on, reverse limit wires
(orange/white).
5. Put operator in open position and adjust appropriate limit
until Open LED limit indicator above the motor is connected
comes on.
6. Placing the gates in the mid-way position may yield better
results when Learning.
7. While LR is still ashing, press and hold Learn until LR is
SOLID (approx/ 5 seconds), then press, OK.*
*A circling cursor should now be displayed. If the circling cursor
display is not seen, repeat Steps 2 & 6.
8. Once Steps 2 & 6 are completed, Learn cycle has been
initialized and operator will begin learning process by scanning
BlueBus port, then run motor(s). *
*If you press Stop at any point before this list of actions is
complete, board will return to, Position Learn condition.
9. Learn procedure is now complete and status display should
read "CL" signifying close limit is active.
NOTICE
For DUAL GATE installations, unplug current motor connected
and repeat Steps 1-5 with second motor. Ensure both motors
are connected to board BEFORE LEARNING.
PRIMARY SETTINGS
This order of operations applies to Force, Slowdown, and
Auto Close settings.
1. Press and release desired setting button.
2. Setting's code will display momentarily.
3. Current setting's value will display.
4. Use up or down to select desired value.
5. Press and release OK button.
6. Display returns to Current Status.
FORCE
Current sensitivity should be set to a level strong enough for
operation under normal conditions yet sensitive enough to
reverse if obstructed.
Setting Values:
1 - Very Sensitive
2
3 - Average (default)
4
5 - Very Strong
SLOWDOWN
Adjusts percentage of acceleration or deceleration when
opening or closing. Setting Slowdown to lowest acceptable
setting provides most reliable operation.
Setting Values:
1 - 5% (recommended for most gates)
2 - 10%
3 - 15% (default)
4 - 20%
5 - 25%
AUTO CLOSE
Adjusts amount of time before gate automatically closes.
Setting Values:
0 - disabled (default)
1-90 - seconds until close begins
The following steps allow for basic setup of the 936 control board. Information on additional features and congurability can
be found in the 1550 or Titan12L Nice Swing Gate Operator Manual.
www.ApolloGateOpeners.com | (800) 878-7829 | Sales@ApolloGateOpeners.com
  • Page 1 1

Nice Apollo 936 Control Board for 1550 / 1650 Gate Openers User guide

936 Control Board for 1550 / 1650 Gate Openers
Nice Apollo
Brand
Nice Apollo
Model
936 Control Board for 1550 / 1650 Gate Openers
Type
User guide
This manual is also suitable for

Nice Apollo 936 Control Board for 1550 / 1650 Gate Openers provides advanced control and customization options for your swing gate operator. With its intuitive interface and comprehensive features, you can easily set up and adjust various parameters to ensure smooth, safe, and reliable operation of your gate system. From learning procedures and primary settings to force adjustment, slowdown control, and auto-close configuration, the 936 Control Board offers a user-friendly experience and enhances the performance of your gate opener.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents