Star Trac E Series CT E-CTi Installation guide

Brand: Star Trac

Model: E Series CT E-CTi

Category: Bicycle accessories

Type: Installation guide

This manual is also suitable for

STAR TRAC FITNESSTM

PVS Bracket 

Installation Manual 



|2



INTRODUCTION

Thank you for adding the STAR TRAC PERSONAL VIEWING SCREEN (PVS) to your Star Trac Purchase. The Personal

Viewing Screen has been designed to provide the user with the most rewarding experience based upon the carefully

planned features it possess. The design elements of this Personal Viewing Screen will provide you with a comfortable,

intuitive, safe and reliable experience, guiding you to a habit-forming lifestyle.

ABOUT THIS MANUAL

This manual is applicable to the STAR TRAC E-UB UPRIGHT BIKE, E-RB RECUMBENT BIKE, E-ST STEPPER, E-TBT

TOTAL BODY TRAINER, and the E-TR TREADMILL. The manual is divided into eight sections, as follows:

Introduction

Provides an overview of each section within the manual.

Before You Get Started

Provides guidelines to help you have a successful installation.

Warnings and Cautions

Helpful safety tips to keep you out of harm’s way.

STAR TRAC Personal Viewing Screen (PVS)

Provides a description of what you will find in your PVS kit.

Installing Your STAR TRAC Personal Viewing Screen (PVS)

Provides a step-by-step instruction set for installing your PVS on the E-UB, E-RB, E-ST, E-TBT and E-TR.

Setting Up Your STAR TRAC Personal Viewing Screen (PVS)

Provides step-by-step instruction set for configuring your PVS with either the NTSC/ATSC or PAL/SECAM screen.

FAQ’s and Troubleshooting

Frequently asked questions and troubleshooting methods to help solve problems that may occur with your PVS.

Regulatory Information

Provides regulatory information for the Star Trac Personal Viewing Screen.



permission from Star Trac. Every effort has been made to keep this information current; however, periodically, changes are made to the information herein, and these

changes will be incorporated into new editions of this publication. All product names and logos are trademarks of their respective owners. Printed in the USA.



|3



BEFORE YOU GET STARTED

CHECK FACILITIES PREPAREDNESS

For a proper installation, please read this guide thoroughly and follow the instructions. Star Trac’s goal is to help you have

a successful and reliable installation, for this reason we have come up with some helpful tips and check list to accomplish

this goal.

EQUIPMENT LAYOUT

Check to see that the equipment you will be adding the PVS are placed where they will be used. It is recommended that

you follow your installation guides for each one of your Star Trac pieces of equipment in making sure that there is ample

space around them to insure a safe and enjoyable experience.

INPUT SIGNAL

In the world of entertainment today you have many choices. Star Trac recommends you know what type of video signal

(cable, analogue, digital, satellite, antenna) is in the club facility and if it has a good signal. Don’t forget every installation

is different. Check to see that you have ample video coaxial cable connections to the locations where the PVS will be

installed.

CABLING

When Radio Frequency signals travel through cabling the signal will degrade over distance. Connectors may degrade the

signal as well. Check each output before connecting to your PVS and make sure you have a clean strong signal to insure

an enjoyable experience. The Star Trac PVS requires a minimum signal strength of 45dBmV for analogue channels, and

40% for digital channels. Your club may require signal amplifiers to achieve a good strong signal. Star Trac recommends

you use a qualified installer for your Audio Visual needs.

ELECTRICAL RECEPTACLES

The Personal Viewing Screen requires a plug-in 60 watt power supply to operate (included). Check with your club facility

to ensure ample electrical receptacles are placed next to the equipment for a safe and proper install. Check with your

contractor to make sure you have enough power.



|4



WARNINGS AND CAUTIONS





This lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user

to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

This exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instruction in the literature accompanying the

appliance.

 

|5



Supplied

• 5MM Hex Allen Key

Not Supplied

• #2 Phillips Screwdriver

• 1/2” Wrench (for E-TRi Kits only)

• Wire Cutters

• Step Stool





Required Tool for Installation

|6



Step 1

Usinga#2Phillipsscrewdriver,removethe(8)

screwsonthebackofthedisplayplastic.Setthe

screwsaside,youwillneedthemforreassembly.



STEP 2

Afterthescrewshavebeenremoved,carefullyopen

thedisplayplastic.Makesurenottodetach/snapthe

innercablesfromthedisplayboard.

DisconnectthegroundwirebetweentheHeartRate

boardandthedisplaymount.



STEP 3

Disconnectthe12‐pinserialconnector,displaycable and

theHeartRatecablefromthedisplay.

Thensetthe

displayaside.



Installing Your PVS Bracket on the E-UB, E-RB, E-CT, E-

ST and

|7







STEP 4

RemovethecapcoverwiththeStarTraclogofrom

theplasticsbyremovingthe2screwsusinga#2

Philipsscrewdriver.Retainthescrewsforlateruse

butthecapcoverisnolongerneededandcanbe

storedforfutureuse.







STEP 5

Removethe(2)M8buttonheadscrewsusinga5mm

HexKey.Retainthescrewsforlateruse.



STEP 6

Itisnowtimetore‐installthedisplaytothebase

unit.Installthe(4)M8Buttonheadscrewsthrough

thePVSmountingbracketintothedisplaymount.

Note:(2)ofthescrewsareinthePVSkit,(retained

fromearlierstep.



STEP 7

Adjustthecapwiththegrommetintoplace.Using

the5mmHexKey,tightentheM8Buttonhead

Screwsto190lb‐in(21.5N‐m)oftorque.Takethe

(2)Phillipsheadscrewsyouremovedfromthe

originalcapandsnuglytightenscrewsdownusinga

#2Phillipsscrewdriver.



Note:Checkthebacksideofthedisplaytoseethatthe

capisseatedproperly.Ifnot,loosenthetwoPhillips

HeadScrews,adjustthecapandthenretightenthe

screws.



|8



STEP 8

BindthecablesfromthePVSnecktotheonesideof

thedisplaymount.Takethetieandpu titthrough

theholeononeofthedisplaymounttube.







STEP 9

Itisnowtimetomakechangestothefrontdisplay.

Disconnectthecenterconsolekeypad.Usinga

#2Phillipsscrewdriverremove(4)screwsthathold

thecenterconsoletothemaindisplay.Retain

screwsforlateruse.Detachthecenterconsolefrom

thedisplay.Youwillnolongerneedthisitem

andit

canbestoredawayforanypossiblefutureuse.



STEP 10

Usinga#2Phillipsheadscrewdriver,removethe

screwthatholdsintheblankcoverwherethenew

HeadPhoneJackmountwillgo.Nextremovethe

blankcover.Youwillnolongerneed thisitemandit

canbestoredawayforanypossiblefutureuse.

Retainscrewforlater

use.



STEP 11

TakethePVScenterconsolefromthekit.







|9



STEP 12

Insertthenewcenterconsoleintothefrontdisplay.

Usinga#2Phillipsscrewdriver,screwinthe(4)

screwsthatweresavedtheoriginalcenterconsole.

Tightenthescrewssotheyaresnug.Attachthe

ribboncablefromthecenterconsoletothedisplay 

board.





STEP 13

TakethecoaxcablefromthePVSmount

andattachittothecoaxcableonthebaseunit.

Attachpowercabletothepowercabl econnector.

Tightentheconnectorssnugtoeachother.



 



STEP 14

Reconnectthecenterconsolekeypadtothemain

display.

ConnecttheRJ45cablefromtheneckintothecenter

consoleboard.







STEP 15

FeedtheHeadPhoneJackcablefromthePVSdisplayneck

throughtheholeinthefrontdisplayplasticswherethe

blankcoverwasremovedearlier.







Powercable



|10



STEP 16

Reconnectthegroundcablethatwasdisconnected

fromtheboardanddisplaymount.





STEP 17

Reconnectthe12‐pinserialconnectorandheart

ratecablethatwasdisconnectedfromthedisplay

board.



Note:onE‐SM,thereisaPausecablethatmustbeconnected

tothedaughterboardontheMainKeypad.



STEP 18

TakethefrontdisplayplasticswiththenewCenter

Consoletothebaseunit.Holdthefrontdisplay

plasticsatthetopwithonehandwhileconnecting

thecables/harnesseswiththeother.



STEP 19

Placethedisplayfrontplasticontotheback.Make

surethebottomofthedisplayfrontisunderthe2

tabsonthedisplaymount.Pressthefrontdisplay

againsttheroundtubeandrotateittotheback.Be

carefulnottopinchanywires.



|11



STEP 20

TaketheEntertainmentHeadPhoneJackfromthe

PVSkitandattachittothecablethatishangingout

ofthefrontofthedisplay.Makesuretheconnector

isseatedallthewayintothejack.Nowslidethejack

intothefrontofthedisplay.Usinga#2

Phillips

screwdriver,fastentheHeadPhoneJackintothe

frontdisplaywiththescrewthatwassavedfromthe

earlier.



STEP 21

Usinga#Phillipsscrewdriver,securethefront

displaytothebackwiththe(8)screwsyou

previouslyremovedandsaved.



STEP 22

NowthePVSisinstalledontheequipment.Connect

yourcoaxcableandpowersupplytotheunit.Take

thepowersupplyfromthePVSkitandplugthesmall

barrelconnectortotheDCinput.Takethe

appropriatePowerAdapterCablefromthekitand

plugitintothepower

supplyandtheelectrical

receptacle.



Onlyusethepowersupply

thatwasprovidedinyour

PersonalViewingScreenKit.

Usingthewrongsupplymay

damageyourPVS



ThiscompletestheinstallationofthePersonalViewingBracket.Nowitistimetoinstallthescreenanddothe



setup.Turntotheappropriatesection foryourPersonalViewingScreenManual.







|12



STEP1

Usinga#2Phillipsscrewdriver,remove

the(8)screwsfromtheupperbackof

thedisplay.Placethecoversomewhere

safetokeepitfrombeingdamaged.

Next,removethe(6)screwsfromthe

lowerbackofthedisplay.Placethe

coverwiththeother

one.Retainallthe

screwsforlateruse.







STEP 2

Removetheuppercapcoverthathasthe

STARTRAClogoonit.Thiscapisheldinbythe

upperbackcover.Youwillnolongerneedthiscap

coverand,ifdesired,youcanstoreitawayforany

possiblefutureuse.



STEP 3

Usinga#2Phillipsheadscrewdriver,removethe

screwbelowtheHotbarthatholdsintheblankcover

wherethenewHeadphoneJackmountwillgo.Next

removetheblankcover.Insertandscrewonthenew

HeadPhoneJackusingthepreviousscrews.









Installing Your PVS Bracket on The E-TRx

|13





STEP 4

DetachtheCenterConsoleRibbonCablefromthe

displayboardbygentlypullingontheribbon

connector.Usinga#2Phillipsscrewdriver,remove

the(4)screwsthatholdthecenterconsoleinplace.

Retainthescrewsforlateruse.Removethecenter

console.Youwillnolongerneedthis

center

consoleand,ifdesired,youcanstoreitaway

foranypossiblefutureuse.





Screws

 



TEP 5

MountthePVSneckontheTreadmill.Usingthe5mmhex

key,screwinthe(2)M8B uttonheadsatthebaseofthe

PVSfirst(donottightenyet).Usingthe5mmhexkeyput

oneoftheM8Buttonheadscrewsintotheholeonthe

PVSneck,thenput

thehexnutwithwasheronthe

backside(donottighten).



STEP 6

Adjustthedisplaycapupordowntoalignwiththe

holesonthedisplayfront.Oncethecapisaligned,

tightenthebuttonheadscrewswiththe5mmhex

key.



Ribbon

|14







STEP 7

NowthattheneckismountedtotheTreadmill,you need

toroutethewirestotheirproperplaces.

Takethecoaxcableandconnectit tothecoaxcable

comingfromtreadmillneck.

ConnecttheDCpowercabletothepowercablecoming

fromtreadmillneck.

NowfeedtheDC

powercableandRJ45cablethrough

thedisplayandoutthecenterconsolehole









 

STEP 9

Takethefemaleheadphonejackfromtheneck

andplugittothemaleheadphonejackcoming

fromthedisplay.





STEP 8

TaketheEntertainmentCenterConsolefromthe

PVSKit.



Fromtheneck

FromtheHotBar



|15



STEP 10

Reconnectthecenterconsolekeypadtothemain

display.

ConnecttheRJ45cablefromtheneckintothecenter

consoleboard.



STEP 11

ClosetheCenterConsole.Usinga#2Phillips

screwdriver,takethescrewsretainedfromearlier

andscrewinthe(4)screwsfrombelowthatholdin

thecenterconsole.Tightenthescrewssnug.



STEP 12

Replacethebottombackplastic.Usinga#2

Phillipsscrewdriverinsertthe(6)screws,retained

fromearlierstep,intotheplasticandtightensnug.



Caution:Donotovertightenscrews.





STEP 13

Replacethetopbackplastic.Usinga#2Phillips

screwdriverinsertthe(8)screws,retainedfrom

earlierstep,intotheplastic.



Caution:Donotovertightenscrews.  



RJ45

|16





STEP 14

Checkthecapwiththeneckandgrommet.Make

surethecapisflushwiththetopbackplastic.

Adjustifnecessary.Usethescrewdriverto

tightenthescrewssnugfromthepreviousstep.

Caution:Donotovertightenscrews.



STEP 15

NowthePVSisinstalledontheequipment.Connect

yourcoax.



ThiscompletestheinstallationofthePersonalViewingBracket.Nowitistimetoinstallthescreenanddothe

setup.Turntotheappropriatesection foryourPersonalViewingScreenManual.







|17



STEP 1

Usinga#2Phillipsscrewdriver,remove

the(8)screwsfromtheupperbackof

thedisplay.Placethecoversomewhere

safetokeepitfrombeingdamaged.

Next,removethe(6)screwsfromthe

lowerbackofthedisplay.Placethe

coverwiththeotherone.Retainallthe

screwsfor

lateruse.



STEP 2

Removetheuppercapcoverthathasthe

STARTRAClogoonit.Thiscapisheldinbythe

upperbackcover.Youwillnolongerneedthiscap

coverand,ifdesired,youcanstoreitawayforany

possiblefutureuse.



STEP 3

MountthePVSneckontheTreadmill.Usingthe5mmhex

key,screwinthe(2)M8B uttonheadsatthebaseofthe

PVSfirst(donottightenyet).Usingthe5mmhexkeyput

oneoftheM8Buttonheadscrewsintotheholeonthe

PVSneck,thenput

thehexnutwithwasheronthe

backside(donottighten).



Installing Your PVS Bracket on The S-TRx and S-TRc

Screws

|18



STEP 4

Adjustthedisplaycapupordowntoalignwiththe

holesonthedisplayfront.Oncethecapisaligned,

tightenthebuttonheadscrewswiththe5mmhex

key.



STEP 5

Connectthemalepowercablethatcomes

throughtheneckoftheunittothefemale

connectorthatcomesfromthebracket.



STEP 6

Makesuretoconnectthecoaxcablethatcomes

fromtheneckisconnectedtothecoaxcablethat

leadstothedisplay.



STEP 7

Usinga#2Phillipsscrewdriver,removethescrew

thatholdsintheBlankHeadPhoneJackCapatthe

lowerfrontofthedisplay.Retainthescrewyouwill

nolongerneedthecapand,ifdesired,youcanstore

itawayforanypossiblefutureuse.Nowtake

the

newHeadPhoneJackfromthePVShardwarekit.

Usethepreviouslyretainedscrewtoreinstallthe

HeadphoneJack.Tightensnugly.



Takethemaleheadphonejackfromtheneckand

plugittotheHeadPhoneJack.



|19



STEP 8

Replacethebottombackplastic.Usinga#2

Phillipsscrewdriverinsertthe(6)screws,retained

fromearlierstep,intotheplasticandtightensnug.

Caution:Donotovertightenscrews.



STEP 9

Replacethetopbackplastic.Usinga#2Phillips

screwdriverinsertthe(8)screws,retainedfrom

earlierstep,intotheplastic.

Caution:Donotovertightenscrews.



STEP 10

Checkthecapwiththeneckandgrommet.Make

surethecapisflushwiththetopbackplastic.

Adjustifnecessary.Usethescrewdriverto

tightenthescrewssnugfromthepreviousstep.



Caution:Donotovertightenscrews.



STEP 11

NowthePVSisinstalledontheequipment.Connect

yourcoax.



ThiscompletestheinstallationofthePersonalViewingBracket.Nowitistimetoinstallthescreenanddothe

setup.Turntotheappropriatesection foryourPersonalViewingScreenManual.





|20



STEP 1. Adding the Power Supply (S-TRx Only)

Slide up the neck and rail gaskets.

Using a #2 Phillips screwdriver, remove the screws

under the neck and rail gaskets.

Remove the shroud.

STEP 2.

t the right side corner on the base frame (when on

the running surface), there are (2) M5-thread-

inserts. Then, install the power supply and secure

with (2) M5 screws.

STEP 4.

Install the (2) T-Tap connectors (female) to the (2)

AC-MCB blue and brown wires:

• Locate one T-Tap connector on the blue wire

about 100mm from the side of quick-disconnect

connector as shown, and flip over to close the T-

Tap connector.

• Use a pair of pliers to crimp the T-Tap

connector. (When fully connected you will hear a

click).

• Do the same thing for the brown wire.

Pliers

T-Tap

Connector

STEP 3.

Plug the 2-contact connector of the power supply

cable, which came with with the PVS kit, onto the

power supply, and connect each male connector to

the female T-tap connector, which was installed in

Step 4. Make sure brown wire is connected to

brown wire and blue to blue (See the right figure for

reference).

Plug the 4-contact connector of the DC power

cable onto the 4-contact connector on the board.

Brown

Wires

Blue

Wires

2-contact

Power

DC Power

Cable

Male

Connecto

Female

Connector

From PVS

Neck

(2) thread-

inserts

Power

Supply

(2) M5 Screws

STEP 4.

Reinstall the shroud by reversion the step 1.

Installing the Power Supply on THE S-TRx

Page is loading ...

Star Trac E Series CT E-CTi Installation guide

Brand: Star Trac

Model: E Series CT E-CTi

Category: Bicycle accessories

Type: Installation guide

This manual is also suitable for

Download PDF

report

Star Trac E Series CT E-CTi Installation guide

This manual is also suitable for

Star Trac E Series CT E-CTi Installation guide

Related papers

Other documents