Pyle Pro PCTVM18 Owner's manual

Brand: Pyle Pro

Model: PCTVM18

Category: Wall & ceiling mounts accessories

Type: Owner's manual

Pyle Pro PCTVM18 is a flat panel ceiling mount designed for TVs up to 70 inches and weighing up to 110lbs. It is made of high-quality materials and has a durable construction. The PCTVM18 is easy to install and comes with all the necessary hardware. It features a universal plate that is compatible with most TVs, and it can be adjusted to fit different ceiling heights. The PCTVM18 also has a built-in safety lock to prevent the TV from falling.

Here are some of the features and possible use cases of the Pyle Pro PCTVM18:

Universal compatibility: The PCTVM18 is compatible with most TVs up to 70 inches, making it a great choice for a wide range of users.

Here are some of the features and possible use cases of the Pyle Pro PCTVM18:

Universal compatibility: The PCTVM18 is compatible with most TVs up to 70 inches, making it a great choice for a wide range of users.

INSTALLATION MANUAL

Flat Panel Ceiling Mount

70"

MAX

200x200

400x400/400x200

600x400/800X400

/300x300

50kg

(110lbs)

RATED

50kg

(110lbs)

RATED

50kg

(110lbs)

RATED

CAU TION: DO NOT EXCEED

RATED LISTED WEIGHT. SERIOUS

INJURY OR PROPERTY DAMAGE

MAY OCCUR!

PCTVM18

NOTE: Read the entire instruction manual before you start installation and assembly.

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.

If any parts are missing or faulty, telephone your local distributor for a replacement.

Package P

D8 ø8.5 ø16 (x6)

P-F

x washer M8 nut (x5)

P-E

M8 (x3)

P-K

x70 iron expansion bolt

M8x60

P-A

(x1) M8x60

P-B

(x1)

M8x55

P-C

(x2)

washer

P-G

(x4)

ø10.5 ø20 (x1)

P-H

x washer

ø8.5 ø17.5 (x3)

P-I

x washer

M8 iron knob

P-J

(x1)

M8x14

P-D

(x2)

top pipe (x1)

bottom pipe (x1)

connect plate (x1)

universal plate (x1)

adapter bracket (x2)

Package M

WARNING

• Do not begin the installation until you have read and understood all the instructions

and warnings contained in this installation sheet. If you have any questions

regarding any of the instructions or warnings, please contact your local distributor.

• This mounting bracket was designed to be installed and utilised ONLY as

specified in this manual. Improper installation of this product may cause damage

or serious injury.

• This product should only be installed by someone with good mechanical ability

who has basic building experience and fully understands this manual.

• Make sure that the supporting surface will safely support the combined weight of

the equipment and all attached hardware and components.

• Always use an assistant or mechanical lifting equipment to safely lift and position

the equipment.

• Tighten screws firmly, but do not over tighten. Over tightening can cause damage

to the items, This greatly reduces their holding power.

• This product is intended for indoor use only. Using this product outdoors could

lead to product failure and personal injury.

M5x14

M-A

(x4) M6x14

M-B

(x4)

washer

M-F

(x4)

M8x20

M-C

(x4)

big spacer

M-H

(x4)

M6x30

M-D

(x4)

M8x30

M-E

(x4) small spacer

M-G

(x8)

2. Assembling the Universal Plate1b. Solid Brick and Concrete Block Mounting: 1. Assembling the Pipes

P-A

P-H

P-B

P-I

P-G

P-J

P-F

P-I

P-F

P-I

P-E

P-F

P-D

Run power cable through pipe.

Attach bottom pipe to top pipe

and fix them at the desired

height. Using correct

combination of screw, washer

and nut.

Attach connect plate to the universal plate using correct combination of screws, washers and nuts.

Assemble the universal plate and bottom pipe with connect plate. Using correct combination of screws

washers, nuts and iron knob.

P-C

P-F

P-E

1b. Solid Brick and Concrete Block Mounting: 1b. Solid Brick and Concrete Block Mounting:

Installers must verify that the supporting surface will safely support the combined weight

of the equipment and all attached hardware and components.

WARNING

3. For Solid Brick and Concrete Mounting

Drill three

pilot holes

60mm

(2.4")

45mm

(1.8")

ø 12mm

(ø 1/2")

Screw ceiling

mount on the

ceiling

flat roof installation

sloped roof installation

Tighten all nuts but do not over

tighten.

P-K

4.Installing the Adapter Brackets

4-1 For Flat Back Screens

4-2 For Recessed Back Screens or to Access A/V Inputs

Tighten all screws but do not over

tighten.

Note: Choose the appropriate screws, washers

and spacers (if necessary) according to the

type of screen.

· Position the adapter brackets as close as

possible to the center of the display.

· Screw the adapter brackets onto the display.

M-F

M-A

M-B

M-C

M-F

M-C

M-G

M-F

M-G

M-C

M-D

M-E

M-F

M-D

M-E

M-H

M-D

M-E

M-F

M-G

M-H

or or

5. Hanging the TV onto the Universal Plate 6. Adjustment

0°

-15°

Attach the TV onto the universal plate and

tighten the safety screws with a proper

screwdriver.

Make sure the TV is safely secured before

releasing.

Loosen the knob and adjust to

the desired angle, then tighten

it.

109

Maintenance

• Check that the bracket is secure and safe to use at regular intervals(at least every three months).

• Please contact your distributor if you have any questions.

Pyle Pro PCTVM18 Owner's manual

Brand: Pyle Pro

Model: PCTVM18

Category: Wall & ceiling mounts accessories

Type: Owner's manual

Here are some of the features and possible use cases of the Pyle Pro PCTVM18:

Universal compatibility: The PCTVM18 is compatible with most TVs up to 70 inches, making it a great choice for a wide range of users.

Download PDF

report

Pyle Pro PCTVM18 Owner's manual

Pyle Pro PCTVM18 Owner's manual

Related papers

Other documents