CARTER-HOFFMANN HBU5A2GM Operating instructions

Brand: CARTER-HOFFMANN

Model: HBU5A2GM

Type: Operating instructions

LOGIX

3 &

LOGIX

4 Series

ALUMINUM HEATED HOLDING

CABINETS & HEATER PROOFERS

OWNERS / OPERATORS MANUAL

Part Number: 18400-3130c Printed in The United States of America Rev: KBA100710

TABLE OF CONTENTS

SAFETY PRECAUTIONS……………………………..…………………. 2

FEATURES & SPECIFICATIONS………..……………..………………. 3-6

UNPACKING, INSPECTION & FREIGHT DAMAGE…………………. 7

INSTALLATION & STARTUP …………………….……………………. 8

DETAILS: CONTROLS AND WATER PANS………………………….. 9

NORMAL OPERATION: LOGIC1 & 3 HB HEATED CABINETS……. 10

NORMAL OPERATION: LOGIC2 & 4 HW HEATER PROOFERS …. 11

FOOD HOLDING GUIDE………………………………………………... 12

DAILY CLEANING PROCEDURES...………………..………………... 13

CABINET MAINTENANCE………………………………………………. 14

WIRING DIAGRAMS...……………………………………… …………... 15

REPLACEMENT PARTS………………………………………………... 16

TROUBLESHOOTING GUIDE …………………………………………. 17

WARRANTY STATEMENT……….……………….……………………. 18

MANUFACTURED BY:

CARTER-HOFFMANN

1551 McCormick Avenue

Mundelein, IL 60060 U.S.A.

Phone: 847-362-5500

Fax: 847-367-8981

Toll Free: 800-323-9793

Email: Service@Carter-Hoffmann.com

HBF18A2GM

MODELS:

LOGIX1 HEATED

CABINETS

(non-insulated)

HBU5A2GM

HBU8A2GM

HBU14A2GM

HBU18A2GM

HBC10A2GM

HBC16A2GM

HBC28A2GM

HBC36A2GM

HBF5A2GM

HBF8A2GM

HBF14A2GM

HBF18A2GM

MODELS:

LOGIX2 HEATER/

PROOFERS

(non-insulated)

HWU5A2GM

HWU8A2GM

HWU14A2GM

HWU18A2GM

HWC10A2GM

HWC16A2GM

HWC28A2GM

HWC36A2GM

HWF5A2GM

HWF8A2GM

HWF14A2GM

HWF18A2GM

MODELS:

LOGIX3 HEATED

CABINETS

(insulated)

HBU5A1GM

HBU8A1GM

HBU14A1GM

HBU18A1GM

HBC10A1GM

HBC16A1GM

HBC28A1GM

HBC36A1GM

HBF5A1GM

HBF8A1GM

HBF14A1GM

HBF18A1GM

MODELS:

LOGIX4 HEATER/

PROOFERS

(insulated)

HWU5A1GM

HWU8A1GM

HWU14A1GM

HWU18A1GM

HWC10A1GM

HWC16A1GM

HWC28A1GM

HWC36A1GM

HWF5A1GM

HWF8A1GM

HWF14A1GM

HWF18A1GM

WARNING: ELECTRIC SHOCK HAZARD

All service requiring access to non-insulated components must be performed by

qualified service personnel. Failure to heed this warning may result in severe

electric shock.

CAUTION: ELECTRIC SHOCK HAZARD

Disconnect this appliance from electrical power before performing any

maintenance or service.

CAUTION: BURN HAZARD

Exposed metal surfaces can be hot to the touch and may cause burns.

SAFETY PRECAUTIONS

WAR NING

NOTE: The technical content of this manual, including any wiring diagrams, schematics, parts breakdown

illustrations and/or adjustment procedures, is intended for use by qualified technical personnel and is

subject to change without notice.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances basic safety precautions should be followed, including the following:

1) Be familiar with the appliance use, limitations and associated restrictions. Operating instructions must

be read and understood by all persons using or installing this appliance.

2) This appliance must be grounded. Connect only to properly grounded outlet.

3) Use this appliance only for its intended purpose as described in the manual.

a. This equipment is specifically designed to hold pre-cooked food at temperature.

This equipment is intended for use in commercial establishments only.

c. This equipment is not designed for industrial or laboratory use.

4) Cleanliness of this appliance and its accessories is essential to good sanitation.

5) DO NOT submerge this appliance in water. This appliance is not jet stream approved. DO NOT direct

water jet or steam jet at this appliance, or at any control panel or wiring. DO NOT splash or pour

water on, in or over any controls, control panel or wiring. DO NOT use corrosive chemicals or vapors

in this appliance.

6) DO NOT store this appliance outdoors. DO NOT use this product near water – for example,

near a kitchen sink, in a wet basement, or near a swimming pool, and the like.

7) DO NOT operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has

been damaged or dropped. Do not immerse cord or plug in water, keep cord away from heated

surfaces, and do not let cord hang over edge of table or counter.

8) DO NOT cover or block any openings on the appliance.

9) Only qualified service personnel should service this appliance.

LOGIX1 NON-INSULATED ALUMINUM HEATED CABINET FEATURES & SPECIFICATIONS

Model

Number

Pan/Tray

Capacity*

12”x20” 18”x26”

Slide Pairs

Provided

Overall Dimensions

Height Depth Width

in (mm)

Caster

Diameter

in (mm)

Class 100

Shipping

Weight

lbs (kgs)

HBU5A2GM

(under-counter)

10 5 5 31-1/16 29-1/2 24-11/16

(789) (749) (627)

(127)

108

(49)

HBC10A2GM

(under-counter)

- 10 10 31-1/16 29-1/2 24-11/16

(789) (749) (627)

(127)

(43)

HBF5A2GM

(under-counter)

10 5 5 31-1/16 29-1/2 24-11/16

(789) (749) (627)

(127)

(45)

HBU8A2GM

(1/2 size)

16 8 8 40-1/16 29-1/2 24-11/16

(1018) (749) (627)

(127)

149

(68)

HBC16A2GM

(1/2 size)

- 16 16 40-1/16 29-1/2 24-11/16

(1018) (749) (627)

(127)

131

(59)

HBF8A2GM

(1/2 size)

16 8 8 40-1/16 29-1/2 24-11/16

(1018) (749) (627)

(127)

137

(62)

HBU14A2GM

(3/4 size)

28 14 14 58-1/16 29-1/2 24-11/16

(1474) (749) (627)

(127)

168

(76)

HBC28A2GM

(3/4 size)

- 28 28 58-1/16 29-1/2 24-11/16

(1474) (749) (627)

(127)

148

(67)

HBF14A2GM

(3/4 size)

28 14 14 58-1/16 29-1/2 24-11/16

(1474) (749) (627)

(127)

155

(70)

HBU18A2GM

(full size)

36 18 18 70-1/16 29-1/2 24-11/16

(1780) (749) (627)

(127)

215

(97)

HBC36A2GM

(full size)

- 36 36

70-1/16 29-1/2 24-11/16

(1780) (749) (627)

(127)

185

(84)

HBF18A2GM

(full size)

36 18 18 70-1/16 29-1/2 24-11/16

(1780) (749) (627)

(127)

198

(90)

* HWU Standard spacing at 3”, adjustable on 1-1/2” centers. HWC standard spacing fixed at 1-1/2”, HWF fixed spacing at 3”

LOGIX1 Features & Benefits

•

Precision-engineered bottom mount heater with superior heat-up and recovery time

•

Analog heat control. Digital thermometer. Temperature range of 90°- 190°F

•

Four sizes, available with adjustable universal, fixed universal or adjustable universal slides

•

All swivel heavy-duty casters, front casters fitted with brakes

•

Field reversible glass door in heavy-duty extruded aluminum frame is standard, black anodized solid aluminum

door is optional

Cabinets with Adjustable Universal, Fixed Universal or Angle Slides

APPROVALS:

3174974

Conforms to UL Std 197

certified to CAN/CSA Std

C22.2 No. 109

3174974

Conforms to

NSF/ANSI

Std 4

LOGIX2 NON-INSULATED ALUMINUM HEATER/PROOFER FEATURES & SPECIFICATIONS

Model

Number

Pan/Tray

Capacity*

12”x20” 18”x26”

Slide Pairs

Provided

Overall Dimensions

Height Depth Width

in (mm)

Caster

Diameter

in (mm)

Class 100

Shipping

Weight

lbs (kgs)

HWU5A2GM

(under-counter)

10 5 5 31-1/16 29-1/2 24-11/16

(789) (749) (627)

(127)

108

(49)

HWC10A2GM

(under-counter)

- 10 10 31-1/16 29-1/2 24-11/16

(789) (749) (627)

(127)

(43)

HWF5A2GM

(under-counter)

10 5 5 31-1/16 29-1/2 24-11/16

(789) (749) (627)

(127)

(45)

HWU8A2GM

(1/2 size)

16 8 8 40-1/16 29-1/2 24-11/16

(1018) (749) (627)

(127)

149

(68)

HWC16A2GM

(1/2 size)

- 16 16 40-1/16 29-1/2 24-11/16

(1018) (749) (627)

(127)

131

(59)

HWF8A2GM

(1/2 size)

16 8 8 40-1/16 29-1/2 24-11/16

(1018) (749) (627)

(127)

137

(62)

HWU14A2GM

(3/4 size)

28 14 14 58-1/16 29-1/2 24-11/16

(1474) (749) (627)

(127)

168

(76)

HWC28A2GM

(3/4 size)

- 28 28 58-1/16 29-1/2 24-11/16

(1474) (749) (627)

(127)

148

(67)

HWF14A2GM

(3/4 size)

28 14 14 58-1/16 29-1/2 24-11/16

(1474) (749) (627)

(127)

155

(70)

HWU18A2GM

(full size)

36 18 18 70-1/16 29-1/2 24-11/16

(1780) (749) (627)

(127)

215

(97)

HWC36A2GM

(full size)

- 36 36

70-1/16 29-1/2 24-11/16

(1780) (749) (627)

(127)

185

(84)

HWF18A2GM

(full size)

36 18 18 70-1/16 29-1/2 24-11/16

(1780) (749) (627)

(127)

198

(90)

* HWU Standard spacing at 3”, adjustable on 1-1/2” centers. HWC standard spacing fixed at 1-1/2”, HWF fixed spacing at 3”

LOGIX2 Features & Benefits

•

Precision-engineered bottom mount heater with superior heat-up and recovery time

•

Analog heat and humidity levels. Digital thermometer. Temperature range of 90°- 190°F

•

Can be operated with or without humidity. Capable of humidified holding as well as proofing

•

Four sizes, available with adjustable universal, fixed universal or adjustable universal slides

•

All swivel heavy-duty casters, front casters fitted with brakes

•

Field reversible glass door in heavy-duty extruded aluminum frame is standard, black anodized solid aluminum

door is optional

Cabinets with Adjustable Universal, Fixed Universal or Angle Slides

APPROVALS:

3174974

Conforms to UL Std 197

certified to CAN/CSA Std

C22.2 No. 109

3174974

Conforms to

NSF/ANSI

Std 4

LOGIX3 INSULATED ALUMINUM HEATED CABINET FEATURES & SPECIFICATIONS

Model

Number

Pan/Tray

Capacity*

12”x20” 18”x26”

Slide Pairs

Provided

Overall Dimensions

Height Depth Width

in (mm)

Caster

Diameter

in (mm)

Class 100

Shipping

Weight

lbs (kgs)

HBU5A1GM

(under-counter)

10 5 5 31-5/8 31-1/2 26-1/2

(803) (800) (673)

(127)

113

(51)

HBC10A1GM

(under-counter)

- 10 10 31-5/8 31-1/2 26-1/2

(803) (800) (673)

(127)

100

(45)

HBF5A1GM

(under-counter)

10 5 5 31-5/8 31-1/2 26-1/2

(803) (800) (673)

(127)

104

(47)

HBU8A1GM

(1/2 size)

16 8 8 40-5/8 31-1/2 26-1/2

(1032) (800) (673)

(127)

159

(72)

HBC16A1GM

(1/2 size)

- 16 16 40-5/8 31-1/2 26-1/2

(1032) (800) (673)

(127)

141

(64)

HBF8A1GM

(1/2 size)

16 8 8 40-5/8 31-1/2 26-1/2

(1032) (800) (673)

(127)

147

(67)

HBU14A1GM

(3/4 size)

28 14 14 58-5/8 31-1/2 26-1/2

(1489) (800) (673)

(127)

183

(83)

HBC28A1GM

(3/4 size)

- 28 28 58-5/8 31-1/2 26-1/2

(1489) (800) (673)

(127)

163

(74)

HBF14A1GM

(3/4 size)

28 14 14 58-5/8 31-1/2 26-1/2

(1489) (800) (673)

(127)

170

(77)

HBU18A1GM

(full size)

36 18 18 70-5/8 31-1/2 26-1/2

(1794) (800) (673)

(127)

235

(107)

HBC36A1GM

(full size)

- 36 36 70-5/8 31-1/2 26-1/2

(1794) (800) (673)

(127)

205

(93)

HBF18A1GM

(full size)

36 18 18 70-5/8 31-1/2 26-1/2

(1794) (800) (673)

(127)

218

(99)

* HWU Standard spacing at 3”, adjustable on 1-1/2” centers. HWC standard spacing fixed at 1-1/2”, HWF fixed spacing at 3”

LOGIX3 Features & Benefits

•

Precision-engineered bottom mount heater with superior heat-up and recovery time

•

Analog heat control. Digital thermometer. Temperature range of 90°- 190°F

•

Four sizes, available with adjustable universal, fixed universal or adjustable universal slides

•

All swivel heavy-duty casters, front casters fitted with brakes

•

Field reversible glass door in heavy-duty extruded aluminum frame is standard, black anodized solid

aluminum door is optional

Cabinets with Adjustable Universal, Fixed Universal or Angle Slides

APPROVALS:

3174974

Conforms to UL Std 197

certified to CAN/CSA Std

C22.2 No. 109

3174974

Conforms to

NSF/ANSI

Std 4

LOGIX4 INSULATED ALUMINUM HEATER/PROOFER FEATURES & SPECIFICATIONS

Model

Number

Pan/Tray

Capacity*

12”x20” 18”x26”

Slide Pairs

Provided

Overall Dimensions

Height Depth Width

in (mm)

Caster

Diameter

in (mm)

Class 100

Shipping

Weight

lbs (kgs)

HWU5A1GM

(under-counter)

10 5 5 31-5/8 31-1/2 26-1/2

(803) (800) (673)

(127)

113

(51)

HWC10A1GM

(under-counter)

- 10 10 31-5/8 31-1/2 26-1/2

(803) (800) (673)

(127)

100

(45)

HWF5A1GM

(under-counter)

10 5 5 31-5/8 31-1/2 26-1/2

(803) (800) (673)

(127)

104

(47)

HWU8A1GM

(1/2 size)

16 8 8 40-5/8 31-1/2 26-1/2

(1032) (800) (673)

(127)

159

(72)

HWC16A1GM

(1/2 size)

- 16 16 40-5/8 31-1/2 26-1/2

(1032) (800) (673)

(127)

141

(64)

HWF8A1GM

(1/2 size)

16 8 8 40-5/8 31-1/2 26-1/2

(1032) (800) (673)

(127)

147

(67)

HWU14A1GM

(3/4 size)

28 14 14 58-5/8 31-1/2 26-1/2

(1489) (800) (673)

(127)

183

(83)

HWC28A1GM

(3/4 size)

- 28 28 58-5/8 31-1/2 26-1/2

(1489) (800) (673)

(127)

163

(74)

HWF14A1GM

(3/4 size)

28 14 14 58-5/8 31-1/2 26-1/2

(1489) (800) (673)

(127)

170

(77)

HWU18A1GM

(full size)

36 18 18 70-5/8 31-1/2 26-1/2

(1794) (800) (673)

(127)

235

(107)

HWC36A1GM

(full size)

- 36 36 70-5/8 31-1/2 26-1/2

(1794) (800) (673)

(127)

205

(93)

HWF18A1GM

(full size)

36 18 18 70-5/8 31-1/2 26-1/2

(1794) (800) (673)

(127)

218

(99)

* HWU Standard spacing at 3”, adjustable on 1-1/2” centers. HWC standard spacing fixed at 1-1/2”, HWF fixed spacing at 3”

LOGIX4 Features & Benefits

•

Precision-engineered bottom mount heater with superior heat-up and recovery time

•

Analog heat and humidity levels. Digital thermometer. Temperature range of 90°- 190°F

•

Can be operated with or without humidity. Capable of humidified holding as well as proofing

•

Four sizes, available with adjustable universal, fixed universal or adjustable universal slides

•

All swivel heavy-duty casters, front casters fitted with brakes

•

Field reversible glass door in heavy-duty extruded aluminum frame is standard doors are standard, solid aluminum

door is optional

Cabinets with Adjustable Universal, Fixed Universal or Angle Slides

APPROVALS:

3174974

Conforms to UL Std 197

certified to CAN/CSA Std

C22.2 No. 109

3174974

Conforms to

NSF/ANSI

Std 4

UNPACKING AND INSPECTION

1. Remove the cabinet from shipping carton, ensuring that all pack-

ing materials and protective plastic has been removed from the

unit.

2. Inspect all components for completeness and condition.

3. If any freight damage is present, a freight claim must be filed im-

mediately with the shipping company.

4. Freight damage is not covered under warranty.

5. Check to insure all components are included: cabinet, instruction

packet and additional accessories.

6. Read operation instructions completely.

7. Appliance should be thoroughly cleaned before use. See

CLEANING INSTRUCTIONS in this manual.

This appliance

should be

thoroughly

cleaned prior to use.

See the CLEANING

INSTRUCTIONS in

this manual.

NOTE: DO NOT discard

the carton or other

packing materials until

you have inspected the

appliance for hidden

damage and checked it

for proper operation.

Refer to SHIPPING

DAMAGE CLAIM

PROCEDURE on

bottom of this page.

FREIGHT DAMAGE PROCEDURE

NOTE: For your protection, please note that equipment in this shipment was carefully inspected

and packaged by skilled personnel before leaving the factory. Upon acceptance of this shipment,

the transportation company assumes full responsibility for its safe delivery.

IF SHIPMENT ARRIVES DAMAGED:

1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight

bill or express receipt, and that the note of loss or damage is signed by the delivery person.

2. FILE CLAIM FOR DAMAGE IMMEDIATELY

: Regardless of the extent of damage. Contact

your dealer immediately.

3. CONCEALED DAMAGE: If damage is unnoticed until the merchandise is unpacked, notify the

transportation company or carrier immediately, and then file a “CONCEALED DAMAGE” claim

with them. This should be done within fifteen (15) days from the date the delivery was made to

you. Be sure to retain the container for inspection.

Carter-Hoffmann cannot assume liability for damage or loss incurred in transit, freight damage is

not covered under warranty. We will, however, at your request, supply you with the necessary

documents to support your claim.

LOCATION

For proper operation and maximum performance, locate the

unit in an ambient air temperature of 70ºF (21ºC).

Avoid placement in areas near exhaust fans or where there

are active air movements.

For safe operation and maximum performance, locate the

unit at least 2” from any wall or combustible material.

Unit must be on a solid level surface.

INSTALLATION AND STARTUP

GROUNDING INSTRUCTIONS

This appliance is equipped with a cord having a grounding

wire with a grounding plug which must be plugged into an

outlet that is properly installed and grounded. In the event of

an electrical short circuit, grounding reduces the risk of elec-

tric shock by providing an escape wire for the electric current.

WARNING—Improper use of the grounding can result in

a risk of electric shock. Consult a qualified electrician or

service agent if the grounding instructions are not completely

understood, or if doubt exists as to whether the appliance is

properly grounded.

If necessary, contact a licensed

electrician to install an appropriate

20 amp electrical circuit with correct

NEMA receptacle.

DO NOT use an extension cord.

Installation procedures must be

performed by a qualified technician

with full knowledge of all applicable

electrical codes. Failure could

result in personal injury and prop-

erty damage.

Damage to unit due to being

connected to the wrong voltage or

phase is NOT covered by warranty.

START UP

1. Prior to use, thoroughly clean the interior of the unit, per

the instructions in this manual. Familiarize yourself with

the controls.

2. Plug the power cord of the cabinet into a grounded outlet

with a electrical service according to the electrical infor-

mation provided below. DO NOT MODIFY CORD PLUG.

3. Set POWER switch to the “ON” position.

4. Do not load product into the cabinet. Allow the heat to

remove any residual oils which may adhere to inside

metal surfaces. A slight emission of smoke is common

during the first few hours of operation.

he ground prong of the power

cord is part of a system designed to

protect you from electric shock in

the event of internal damage.

DO NOT cut off the large round

ground prong or twist a blade to fit

an existing receptacle.

CAUTION:

Electrical Shock Hazard

Unit is not waterproof, to avoid

electrical shock, keep unit from be-

ing submerged in water. Do not

operate if unit has been in contact

with water.

IMPORTANT:

Power cord is 8' long

IMPORTANT:

Not under warranty

WARNING:

Risk of personal injury

WARNING:

Risk of personal injury

LOGIC1 & LOGIC3 Models

beginning with HB

LOGIC2 & LOGIC4 Models

beginning with HW

DETAILS: CONTROL PANELS & WATER PANS

LOGIX1 & LOGIX3 HB Series Heated Holding Cabinets

LOGIX2 & LOGIX4 HW Series Heater/Proofer Cabinets

ON/OFF power switch

and indicator light

Heat control knob. Settings from 1 (low heat) to 7 (high heat)

Heating element cycle light

Digital temperature read-out

ON/OFF power switch

and indicator light

Heat control knob. Settings from

1 (low heat) to 7 (high heat)

Heating element cycle light

Digital temperature

read-out

Humidity control knob. Settings from

1 (low humidity) to 7 (high humidity)

Humidity element cycle light

Humidity pan (manual fill): check and fill every 2 hours

when operating cabinet with humidity

Water trough for condensation: collects and deposits

condensation into pan below

Condensation pan: check and empty periodically

WATER PAN LOCATIONS

NORMAL OPERATION—LOGIX1 & LOGIX3 HB HEATED CABINETS

CAUTION:

HOT SURFACE

Inner and outer surfaces of

the unit will be very hot dur-

ing and after operation.

Avoid touching the cabinet

when loading or removing

product.

FIRST USE

Before using the cabinet, familiarize yourself with the heater con-

trols. See page 9 for details. Plug the cabinet into a proven power

source. See electrical specifications on page 8.

HOLDING

1. Turn the cabinet on using the power switch located on the far left

side of the control panel. Once the switch is turned on, the

power indicator light will illuminate.

2. A water pan is provided in the base of the cabinet to provide a

small amount of passive humidity, if desired. Fill pan with clean

warm water. Check water level every 2 hours and refill as

needed. This step is optional; cabinet be also be operated

without water in the pan.

3. To adjust the temperature setting, rotate the HEAT dial clock-

wise to increase temperature and counter-clockwise to decrease

temperature to the desired set point. Temperature dial settings

range from 1 to 7, with 1 being the lowest temperature and 7

being the highest temperature. HEAT cycle light will turn on and

off as the heat thermostat cycles.

4. Wait approximately 25 minutes for the cabinet to preheat. Digital

readout dial on right side of control panel will display actual

cabinet temperature*.

5. Load food pans into cabinet. NOTE: Follow all food safety guide-

lines. Put hot, cooked food into the cabinet. This cabinet is not

intended to reheat food. Food must be cooked and at safe serv-

ing temperature prior to being placed in the cabinet.

6. When removing items, start at the bottom and work up. This will

keep food hotter and eliminate spillage onto lower items.

Operating ranges:

- air temp: 90ºF-190ºF

*For food safety reasons,

it is recommended that

the holding temperature

be set at 140°F or higher.

NORMAL OPERATION—LOGIX2 & LOGIX4 HW HEATER PROOFERS

CAUTION:

HOT SURFACE

Inner and outer surfaces of

the unit will be very hot dur-

ing and after operation.

Avoid touching the cabinet

when loading or removing

product.

FIRST USE

Before using the cabinet, familiarize yourself with the heater con-

trols. See page 9 for details. Plug the cabinet into a proven power

source. See electrical specifications on page 8.

HOLDING

1. If humidity is desired, a water pan is located at the bottom of the

cabinet. This pan will provide active humidification up to 90%RH

(depending on temperature). Fill water pan with clean warm

water. NOTE: Cabinet may also be operated without water.

2. Turn the cabinet on using the power switch located on the far left

side of the control panel. Once the switch is turned on, the

power indicator light will illuminate.

3. To adjust the temperature setting, rotate the HEAT dial clock-

wise to increase temperature and counter-clockwise to decrease

temperature to the desired set point. Temperature dial settings

range from 1 to 7, with 1 being the lowest temperature and 7

being the highest temperature.

4. To adjust humidity, rotate the humidity dial clockwise to

increase humidity and counter-clockwise to decrease humidity.

If humidity is not required, rotate dial counter-clockwise to the off

position (line up dot on knob with white hash mark on control

panel).

5. Wait approximately 25 minutes for the cabinet to preheat. Digital

readout dial on right side of control panel will display actual

cabinet temperature*.

6. Load food pans into cabinet. NOTE: Follow all food safety guide-

lines. Put hot, cooked food into the cabinet. This cabinet is not

intended to reheat food. Food must be cooked and at safe

serving temperature prior to being placed in the cabinet.

7. When removing items, start at the bottom and work up. This will

keep food hotter and eliminate spillage onto lower items.

PROOFING

1. Follow instructions above for holding. Note: water pan at base

of cabinet must be filled with clean warm water.

2. For proofing settings, rotate HEAT knob clockwise to 3.5 to 4

(approximately 90°F to 100°F) and rotate HUMIDITY knob clock-

wise to 7 (90%+ RH).

3. Allow cabinet to preheat for approximately 25 minutes and load

food according to the instructions above.

Operating ranges:

- air temp: 90ºF-190ºF

- humidity: 0-90%RH

Water reservoir:

When using the water reser-

voir for humidified holding or

proofing, check water level

every 2 hours and refill if

needed.

CAUTION:

WATER HAZARD

A water trough is located at

the base of the cabinet to

collect and direct condensa-

tion into black plastic con-

densation pan below. Make

sure to periodically check

and empty the pan to avoid

overflow & slip hazard.

*For food safety reasons,

we recommend that the

holding temperature

should be set at or above

140°F.

FOOD HOLDING GUIDE

NOTE: Times and temperatures

observed in a test kitchen environ-

ment. Times and temperatures

may vary, depending on initial food

quality, initial cooked temperature

and user expectations of accept-

able food quality.

PRODUCT SET TEMPERATURE

(°F /°C)

MAXIMUM TIME

(MINUTES)

Bacon, Canadian 180°F / 82°C 30

Bacon, Crisp (uncovered) 180°F / 82°C 30

Baked Potato 180°F / 82°C 60

Biscuits 170°F / 77°C 60

Casseroles 175°F / 79°C 90

Chops, Sliced Meats 160°F / 71°C 60

Chicken, Fried (uncovered) 170°F / 77°C 30

Chicken, Boneless Breasts 175°F / 79°C 60

Chicken Nuggets, Deep Fried (uncovered) 190°F / 88°C 25

Chicken, Pre-Cooked Grilled Boneless Patties 150°F / 66°C 90

Coffee Cakes (uncovered) 170°F / 77°C 60

Cookies (uncovered) 175°F / 79°C 90

Crab Legs 160°F / 71°C 45

Croissants 170°F / 77°C 45

Eggs 160°F / 71°C 45

Fish, Deep-Fried (uncovered) 170°F / 77°C 30

Fish, Baked 155°F / 68°C 45

Fish, Broiled 155°F / 68°C 45

French Toast 165°F / 74°C 60

Gravies / Sauces 170°F / 77°C 45

Hamburgers / Ground Meat Patties 180°F / 82°C 45

Hot Dogs 180°F / 82°C 90

Muffins 170°F / 77°C 60

Omelets 160°F / 71°C 30

Pancakes 180°F / 82°C 30

Pasta 175°F / 79°C 60

Pastries 165°F / 74°C 30

Pizza (uncovered) 180°F / 82°C 15

Pizza (boxed) 180°F / 82°C 60

Poppers, Deep Fried (uncovered) 190°F / 88°C 25

Poultry, Whole, bone-in 175°F / 79°C 60

Poultry, Cut-up, bone-in 175°F / 79°C 60

Ribs 175°F / 79°C 90

Rice 175°F / 79°C 30

Roasts / Bone-in Meats 165°F / 74°C 90

Sausage 180°F / 82°C 90

Shrimp / Shellfish 150°F / 66°C 60

Soups (broth) 185°F / 85°C 90

Tortillas (soft) 180°F / 82°C 60

Vegetables 175°F / 79°C 45

CAUTION: SAFE

FOOD HOLDING

PRACTICES

RECOMMENDED

Cooking food to a safe tem-

perature, holding at a tem-

perature of at least 140°F is

critical in the prevention of

foodborne illness. Hold only

cooked, hot food at 140°F

or higher. This cabinet is

not intended to cook or re-

heat food. Food must be at

appropriate temperature

before being placed into

cabinet.

140°F

41°F

DANGER ZONE: 41°F

to 140°F Bacteria

grow rapidly

COOK TO AT LEAST

165°F Destruction of

most bacteria

165°F

HOLD at 140°F or higher

DAILY CLEANING PROCEDURES

1. After all food products have been removed from the cabinet,

turn the power switch to “OFF” and allow the cabinet to cool

completely.

2. Unplug the unit prior to any cleaning.

3. Remove the rack assemblies.

4. Make sure the power cord is not hooked into the cord hook.

Open cabinet door and empty water reservoir. Remove the

heater module by lifting up the front enough to clear its detent,

and then pull the module out of the cabinet. The power cord

will slide through the access hole at the rear of the cabinet.

5. Inspect and clean the areas where there are vents or filters,

making sure no water gets into the internal controls or

electrical areas of the cabinet.

6. Clean the inside of the cabinet as well as the removed parts.

Reinstall when all parts are dry and clean. Empty and clean

black plastic condensation pan.

7. A solution of two tablespoons of baking soda per quart of

warm water is sufficient for most cleaning jobs. Mild soap or

detergent may be used on heavily soiled interiors—follow

manufacturer’s directions.

8. If cabinet has a clear glass door, clean with window cleaner,

taking care not to get any of the solution on the aluminum

cabinet walls. Stubborn deposits may be cleaned with a mild

soap and water and then rinsed with clean water. Use a soft,

non-abrasive cloth to avoid scratching the door.

9. Control panel should be washed with a clean, damp, non-

abrasive cloth and chlorine-free detergent. Rinse thoroughly

with clean damp cloth and allow to dry. Do not use abrasive

cleaners, waxes, car polish, or substances containing strong

aromatic solvents or alcohol. If the control knob(s) need to be

removed for cleaning, simply pull the knob out, clean the con-

trol panel and knob, and then replace the knob.

CAUTION:

ELECTRIC SHOCK

HAZARD

Disconnect appliance from

electric power before cleaning.

CAUTION:

HOT SURFACE

Exposed surfaces can

be hot to the touch and may

cause burns. Allow appliance

to cool before cleaning.

IMPORTANT:

DO NOT spill or pour

water into controls,

control panel or wiring.

Water damage is not covered

by warranty.

CAUTION

Beware of sharp

edges with sheet

metal during cleaning process.

CAUTION:

Do not use strong detergents, alkalis, ammonia solutions or

abrasive cleaners. Use only cleaning agents approved for alu-

minum and only in the recommended manufacturer’s concentration. Do

not use steel wool pads—ferrous deposits will cause rusting.

Use of cleaning agents that are not recommended for aluminum may

cause permanent damage to the cabinet. THIS DAMAGE IS PERMA-

NENT, COSTLY TO REPAIR AND IS NOT COVERED BY THE

WARRANTY.

CABINET MAINTENANCE

CASTERS

Some cabinets may have caster bearings that are equipped with

Zerk grease fittings so that they may be easily lubricated with a

grease gun. Lubricate bearings at least once every six months.

HINGE MAINTENANCE

Make sure all joints remain sealed and door latches do not stick. If

necessary, use WD-40 to keep door latches from sticking. Do not

use oil.

REVERSING THE DOOR

Reversing the door takes about 30 minutes & requires two people.

1. Using a small screwdriver, pry off the hinge covers and set

aside. Removing the covers will allow access to the inside

hinge screws. Remove the three screws that hold each hinge

to the cabinet. DO NOT REMOVE THE SCREWS THAT

HOLD THE HINGES TO THE DOOR. Remove the door, tak-

ing care not to let it fall.

2. Remove the door strike plate and screws adjacent to the door

opening on the cabinet. Reinstall door strike plate and screws

on opposite side of the cabinet.

3. Screw hinges onto opposite side of the door.

4. With the help of another person, hold door up to the cabinet

and attach with the screws removed in step one. Before tight-

ening the screws, be sure the door is flush, level and square.

Replace the hinge covers.

WARNING:

DO NOT perform

these procedures

while the cabinet is turned on

or heated. Turn off the power

and wait for the cabinet to cool

to room temperature.

CAUTION:

Do not move cabinet

unless door is se-

curely closed. Serious dam-

age to hinges and door may

result if bumped into tables,

walls, or other equipment when

the doors are open.

Logix1 & Logix3 HB SERIES

120 VOLT, 1800 WATT, 15AMP, 1 PH, 60 HZ

Logix2 & Logix4 HW SERIES

120 VOLT, 2100 WATT, 17.5 AMP, 1 PH

WIRING DIAGRAMS

REPLACEMENT PARTS

Use only (OEM) original equipment manufacturer replacement parts. Using unauthorized parts may

cause serious injury or damage to the cabinet. Replacement parts should be installed by a qualified

service technician.

Contact Carter-Hoffmann with your model and serial number for replacement parts.

Call: 800-323-9793 or

Email: [email protected]

Part Number HB LOGIX1 & LOGIX3 Series Description

18600-0046 Hi limit—open at 300°F, close at 250°F

18602-0083 On/Off switch 20 Amp

18602-0031 Switch boot

18608-0010 Knob—heat

18605-0022 Power cord-8’

18606-0221 5-20P plug

18612-0131 Heat element 1700 watt

18616-0071 Transformer

18614-0360 Fan motor

18614-0321 Fan motor blower wheel

18314-0019 1.8 qt. black condensation pan

18600-0017 Thermostat

18614-0322 Muffin fan

18616-0073 Digital thermometer

18616-0071 Transformer for digital thermometer

18601-1171 Red indicator light, power and heat

Part Number HW LOGIX2 & LOGIX4 Series Description

18600-0046 Hi limit—open at 300°F, close at 250°F

18602-0083 On/Off switch 20 Amp

18602-0031 Switch boot

18608-0010 Knob—heat or humidity

18605-0022 Power cord—8’

18606-0221 5-20P plug

18612-0131 Heat element 1700 watt

18612-0132 Water pan element 350 watt

18616-0071 Transformer

18614-0322 Muffin fan

18614-0360 Fan motor

18614-0321 Fan motor blower wheel

18314-0019 1.8 qt. black condensation pan

18600-0017 Thermostat—heat element

18600-0016 Thermostat—humidity element

18616-0073 Digital thermometer

18616-0071 Transformer for digital thermometer

18601-1171 Red indicator light, power, heat & humidity

TROUBLESHOOTING GUIDE

SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY

No power on display Not plugged in or circuit breaker

tripped

Check or reset circuit breaker

Connect to proper receptacle

Power cord damaged Check - replace if required

Circuit breaker tripped Check circuit breaker

Power switch damaged or defective Check - replace if required

Food dries out too

quickly

Operation where product temp is too

high; food pans should be covered

Check product temps going into

holding cabinet; cover food pans

Control incorrectly set or defective Check proper operation or calibration

of control

Internal wiring error

Call service technician

Element hi-limit trip / defective Call service technician

Takes too long to

get to temperature

Improper voltage Call service technician to verify

incoming voltage matches cabinet

specifications.

Unit is hot

but low or no airflow

Internal wiring error Call service technician

Circulation motor has quit Call service technician

Improper voltage Call service technician to verify

incoming voltage matches cabinet

specifications.

Unit is on, motors

are running but no

heat

NOTE:

The technical content of this manual,

including any wiring diagrams, schemat-

ics, parts breakdown illustrations and /

or adjustment procedures, is intended

for use ONLY by qualified technical

personnel

NOTE:

For warranty service, call Carter-Hoffmann

direct at 800-323-9793 for authorization,

we will dispatch the nearest authorized

service agency.

Carter-Hoffmann Warranty:

Carter-Hoffmann (“CARTER-HOFFMANN”) warrants to the initial purchaser of its standard Carter

Line Products that CARTER-HOFFMANN will, at its option, repair or replace, during the warranty

period set forth below, any part of such products made necessary due to a defect in material or work-

manship which is present when the product leaves its factory and which manifests itself during the war-

ranty period under normal use and service.

This warranty applies only to original equipment owned and possessed by the initial purchaser and the

warranty period begins on the date of original shipment from the CARTER-HOFFMANN factory and

extends as follows: to component parts and labor for 12 months (36 months on hotLOGIX holding

cabinets and cook & hold cabinets); to refrigeration compressor unit for one year (limited to replace-

ment only - not to include labor for removal, repair or replacement).

Repair or replacements under this warranty will be performed, unless otherwise authorized in writing

by CARTER-HOFFMANN, at its factory. All parts or components to be repaired or replaced under this

warranty are to be shipped prepaid to CARTER-HOFFMANN, with reimbursement credit for such part

or component to be given if found by CARTER-HOFFMANN to be defective.

CARTER-HOFFMANN neither makes nor assumes and does not authorize any other person to make or

assume any obligation or liability in connection with its products other than that covered in this war-

ranty. This warranty applies only within the continental United States and Canada. In Alaska and Ha-

waii, this warranty applies only to and is limited to the supply of replacement parts.

Warranty Exclusions and Limitations:

Any implied warranty of merchantability or fitness for a particular purpose is hereby specifically dis-

claimed by CARTER-HOFFMANN. There are no warranties, expressed or implied, which extend be-

yond the description on the face hereof. This warranty does not cover and CARTER-HOFFMANN shall

not under any circumstances be liable for any incidental, consequential or other damages (such as in-

jury to persons or property, loss of time, inconvenience, loss of business or profits, or other matters not

specifically covered) arising in connection with the use of, inability to use, or failure of these products.

Specifications subject to change through product improvement and innovation.

3-YEAR WARRANTY on HOTLOGIX HOLDING CABINETS

Carter-Hoffmann

1551 McCormick Ave.

Mundelein, Illinois, 60060 USA

Phone: 847-362-5500 Toll free: 800-323-9793 Fax: 847-367-8981

Sales and Marketing E-mail: sales@carter-hoffmann.com

Service E-mail: [email protected]

Company Website: www.carter-hoffmann.com

CARTER-HOFFMANN HBU5A2GM Operating instructions

CARTER-HOFFMANN HBU5A2GM Operating instructions

CARTER-HOFFMANN HBU5A2GM Operating instructions

Related papers

Other documents