DT Research DT500 Basic Operation Guide

DT Research
Brand
DT Research
Model
DT500
Type
Basic Operation Guide
Integrated LCD Systems
ENGLISH
Integrated LCD System
BASIC OPERATION GUIDE
ENGLISH
4
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com
Copyright © 2018, DT Research, Inc. All Rights Reserved.
INTRODUCTION
Thank you for acquiring the DT Research Integrated LCD System, a 19-inch and 21.5-inch TFT
display-integrated, thin compung plaorm, offering adaptability to mounng configuraons and
applicaons, including informaon appliance, thin client for server compung, and disk drive-
equipped opons.
Please take a few moments to review the contents of this document to ensure that the setup and
startup proceed smoothly. The DT Research Integrated LCD System is ready for use, out of the box,
in its default configuraon when powered by the power source provided. The following discussion
offers guidance on the hardware elements and features of the DT Research Integrated LCD System.
Please refer to your device provider for informaon pertaining to the soware operang system or
soware applicaons.
Package Contents
O
• ne DT Research Integrated LCD System with desktop stand
A
• C/DC power adapter with power cord
B• asic operaon guide
Precauons
Always exercise care when operang and handling the DT Research Integrated LCD System.•
Never disassemble any poron of the enclosure, as this will void any product warranty on the •
DT Research Integrated LCD System.
Do not use any AC/DC adapter other than the one provided with the device or a replacement •
acquired from the manufacturer.
I
• n the unlikely event that smoke, abnormal noise, or strange odor is present, immediately power
down the DT Research Integrated LCD System and disconnect all power so
urces. Please report
the problem to your device provider immediately.
BOG0041218ILENG
Mounng
The DT Research Integrated LCD System is designed to be secured to VESA-compliant mounng
arms or stands. This is accomplished by equiping the standard metal base on the rear of the display
unit. The VESA-compliant mounng holes at the rear of the device will mate with VESA mounts or
arms to meet the requirements of the deployment.
Remove the detachable base by pressing 1.
upward to remove the cover, then unscrewing
the four screws aaching the base to the
display.
Aach the new VESA-compliant mounng 3.
device or stand to the display.
The display without the base.2.
The display successfully mounted on a 4.
VESA-compliant mounng arm.
Integrated LCD Systems
I/O Panels & Funcon Buons
The
DT Research
Integrated LCD System has a comprehensive set of I/O ports. The following ports
are located along the lower rear edge of the display unit.
Two USB 2.0 ports1.
COM ports2.
Audio-out jack3.
Microphone-in jack4.
Two USB 2.0 ports5.
Ethernet port (RJ45)6.
DC-in jack7.
ENGLISH
2
3
ENGLISH
Packaging
The DT Research •
Integrated LCD System
is packaged with recyclable materials
and designed for maximum protecon in transportaon and handling.
When possible, please save the packaging carton and protecve inserts for •
re-use if there is ever a need to ship the DT Research
Integrated LCD System
.
Buon Descripon
8. Programmable
The three buons are intended to be user programmable via soware in
applicable operang systems.
9. Power
M
• ay be configured to perform different funcons, depending on the
soware operang system.
D
• epending on the OS, a brief, firm push will trigger soware-enabled
entry into Shutdown or Standby modes. Push in similar manner to Restart or
to exit Standby mode.
P
• ush an
d hold for over 4 seconds to forcefully shut down the device. This
method of powering off should only be used when proper shutdown
through soware is not possible.
1
1
2
2
3
3
4
4
5
5
7
7
8
9
8
9
6
6
19-inch and 22-inch LCD Models
17-inch and 19-inch LCD Models
Opons
The DT Research Integrated LCD System has a number of oponal configuraons in both soware
and hardware. These include:
IR or capacive touch screen 1.
Magnec card reader2.
Built-in 802.11 WLAN module3.
Cleaning the Screen
A screen cleaning soluon that is non-alcohol and non-abrasive can be used to clean the touch •
screen.
We suggest cleaning with a micro-fiber cloth.•
Please spread the soluon on to the cloth and then clean the touch screen.•
Cleaning the An-microbial Enclosure (DT500-MD series)
Use a so/non-abrasive cloth moistened with water to clean the enclosure.•
If using a cleaner, an alcohol-free and oxide-free cleaning liquid is recommended.•
To prevent scratching the an-microbial coang, please wipe gently.•
  • Page 1 1
  • Page 2 2

DT Research DT500 Basic Operation Guide

DT Research
Brand
DT Research
Model
DT500
Type
Basic Operation Guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents