QUICK SETUP GUIDE
RF-HTC4818, 4.8A 4-Port Charging Hub
Before using your new product, please read these instructions to prevent any damage.
USING THE POWER HUB
Note: The USB hub is designed for constant use. It can be left
plugged in at all times, even if no USB cords are connected.
1. Plug the USB hub into a power outlet.
2. Plug your USB devices into the USB ports to
power or charge them.
3. Slide the switch on the side to turn the trace
lighting on or o.
PACKAGE CONTENTS
• USB Power Hub
• Quick Setup Guide
FEATURES
• 4 USB ports with 4.8A
total output for constant
power delivery for fast
charging of your devices
• LED lighting around
each USB port for
easy connection
(can be turned o)
• Premium design matches
modern home theater systems
• Weighted base keeps
the USB hub in place
TROUBLESHOOTING
USB hub isn't charging your device:
• Make sure that the USB hub is plugged into a working power
outlet. If you're using a surge protector, make sure
that it's turned on.
• Make sure that your USB cable is properly inserted into your
USB device and the USB hub.
LED trace lighting isn't on
• Make sure that the USB hub is plugged into a working
power outlet. If you're using a surge protector, make sure
that it's turned on.
• Slide the light switch to turn on the trace lights.
USB ports
Light
switch
ONEYEAR LIMITED WARRANTY
Visit www.rocketfishproducts.com for details.
CONTACT ROCKETFISH:
For customer service please call 1-800-620-2790
www.rocketfishproducts.com
ROCKETFISH is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2017 Best Buy. All rights reserved
Made in China
V1 ENGLISH 17-0668
SAFETY INFORMATION
• RISK OF ELECTRIC SHOCK - Use only in dry locations and only
indoors.
• DO NOT plug into another relocatable power tap.
• DO NOT “daisy chain” surge protectors.
• DO NOT use with any aquarium equipment.
• DO NOT use if correctly grounded outlets are not available.
• DO NOT install this device if there is not at least 30 feet (10
meters) or more of wire between the electrical outlet and
electrical service panel.
• This device features internal protection that will disconnect
the protective component at the end of its useful life, but will
maintain power to the load – WHICH WILL BE UNPROTECTED.
If you don't want your equipment at risk, follow the
manufacturer’s instructions for replacing the device.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
ICES-003:
This Class B digital apparatus complies with Canadian ICES-003
SPECIFICATIONS
Line voltage
100-125V, 60Hz, 0.7A
Dimensions:
(L×W×H):
USB hub: 2.9 x 2.2 x 1.4 in (74 x 56 x 36.5 mm)
Adapter (excluding plug):
3.2 x 2 x 1.3 in (83 x 50 x 33.5 mm)
USB output
5V DC, 4.8A / 24W
/