Introduction
Cable-Connection
Component
Quantity
T45
1
Bracket
1
Cable
9PIN 6PIN 5PIN 4PIN (Power, 485 CON)
Screw
For Bracket 4ea T3x20mm
For T45-K 2ea M3x6mm
1. POWER: CN700(DC-In) connects with DC12V and GND. The direction of the GND
and VCC doesn’t matter.
2. TCP/IP: Shows TCP/IP connects with T45 using the HUB. No distance limits using
TCP/IP and configure access control system with LAN or WAN (Refer to user
manual or guardian software manual for the IP setup.
3. RS-485: Shows the connection CN700(DC-IN) and RS-232/485 Converter .
For the full version of this manual, please visit COMMAX online
www.commax.com > Customer > Manual. Download full manuals for installation and user.
Access Control IDentry-T45-T User Manual
http://www.commax.co.kr/boardnew/lib/downfile.php?db=TB_ENGLISH_manual&fnum=155
Access Control IDentry-T45-K User Manual
http://www.commax.co.kr/boardnew/lib/downfile.php?db=TB_ENGLISH_manual&fnum=154
Access Control IDentry-T45 Installation Manual
http://www.commax.co.kr/boardnew/lib/downfile.php?db=TB_ENGLISH_manual&fnum=117
Access Control IDentry-CAMS-S User Manual
http://www.commax.co.kr/boardnew/lib/downfile.php?db=TB_ENGLISH_manual&fnum=133
①
②
③
IDentry-T45
Quick Manual
July 2015 Ver. 1
Cable-Connection
4. WIEGAND OUT: If connected to other main controller, it works as a card reader
or fingerprint reader only not controller. CN506(Wiegand out) connects with
card reader port of main controller and transmit the data via Wiegand.
5. RF CARD READER: Connects the cable of the RF card reader to CN503.
Connection would be variable for each reader. (Follow the manual of each
RF card reader)
6. SENSOR: Shows T45 connected with sliding door and relevant controls; door
contact, door sensor, exit button, infrared sensor.
7. RELAY: Shows physical access controls of T45 by connecting many devices which
detect certain situation through the sensors explained in the above. Electric strike
or alarm devices to be operated with T45 using the connection of CN501.
⑤
④
⑥
⑦
(ex:IDentry-T20-F)
COMMAX Co.,Ltd. #531-11, Sangdaewon-dong, Jungwon-gu, Seongnam-city, Kyunggi-do, Korea
User Registration
Cautions
* In case of the absence of the admin, getting at least more than two admin staff charged
is recommended.
If you don’t need CARD, it is possible to skip the rest of the process.( from NO.7)
1. Press * on the main.
2. Press # with registered No. and ID as an administrator.
3. Select users to press #.
4. Select registration to press #.
5. Use F1 or F2 to move, put ID and press # to designate authority It can register
fingerprints, cards and pictures to put a button.
6. Enter fingerprint when a sensor light comes. *It totally registers fingerprint for 3 times
and it would move to previous menu to press *If it finishes fingerprint registration.
7. A card that would use for enter/exit should be read if puts on a screen and press #
to register a card.
8. Register to press # after shooting button for a photo.
9. Go back to a main menu to press F4 if all procedures are clear.
- Keep out of direct sunlight and heat radiation sources.
- Shall not be exposed to dripping or splashing and no objects filled with
liquid such as vases, shall be placed on the products.
- When cleaning, do not use liquid solvent or wet cloth. Wipe with soft cloth.
- Never disassemble or modify this device in any way. (COMMAX Co., Ltd is
not liable for problems caused by unauthorized modification or attempted
repair )
- Do not install this device near by TV, monitor or magnetic interference.
- If the product fails to operate normally, contact the authorized dealer or
service center.
/
