Commax IDentry-T45 Owner's manual

Brand: Commax

Model: IDentry-T45

Type: Owner's manual

Introduction

Cable-Connection

Component

Quantity

T45

Bracket

Cable

9PIN 6PIN 5PIN 4PIN (Power, 485 CON)

Screw

For Bracket 4ea T3x20mm

For T45-K 2ea M3x6mm

1. POWER: CN700(DC-In) connects with DC12V and GND. The direction of the GND

and VCC doesn’t matter.

2. TCP/IP: Shows TCP/IP connects with T45 using the HUB. No distance limits using

TCP/IP and configure access control system with LAN or WAN (Refer to user

manual or guardian software manual for the IP setup.

3. RS-485: Shows the connection CN700(DC-IN) and RS-232/485 Converter .

For the full version of this manual, please visit COMMAX online

www.commax.com > Customer > Manual. Download full manuals for installation and user.

Access Control IDentry-T45-T User Manual

http://www.commax.co.kr/boardnew/lib/downfile.php?db=TB_ENGLISH_manual&fnum=155

Access Control IDentry-T45-K User Manual

http://www.commax.co.kr/boardnew/lib/downfile.php?db=TB_ENGLISH_manual&fnum=154

Access Control IDentry-T45 Installation Manual

http://www.commax.co.kr/boardnew/lib/downfile.php?db=TB_ENGLISH_manual&fnum=117

Access Control IDentry-CAMS-S User Manual

http://www.commax.co.kr/boardnew/lib/downfile.php?db=TB_ENGLISH_manual&fnum=133

①

②

③

IDentry-T45

Quick Manual

July 2015 Ver. 1

Cable-Connection

4. WIEGAND OUT: If connected to other main controller, it works as a card reader

or fingerprint reader only not controller. CN506(Wiegand out) connects with

card reader port of main controller and transmit the data via Wiegand.

5. RF CARD READER: Connects the cable of the RF card reader to CN503.

Connection would be variable for each reader. (Follow the manual of each

RF card reader)

6. SENSOR: Shows T45 connected with sliding door and relevant controls; door

contact, door sensor, exit button, infrared sensor.

7. RELAY: Shows physical access controls of T45 by connecting many devices which

detect certain situation through the sensors explained in the above. Electric strike

or alarm devices to be operated with T45 using the connection of CN501.

⑤

④

⑥

⑦

(ex:IDentry-T20-F)

COMMAX Co.,Ltd. #531-11, Sangdaewon-dong, Jungwon-gu, Seongnam-city, Kyunggi-do, Korea

TEL +82-31-7393-540~550 FAX +82-31-745-2133 Mail: [email protected]

User Registration

Cautions

* In case of the absence of the admin, getting at least more than two admin staff charged

is recommended.

If you don’t need CARD, it is possible to skip the rest of the process.( from NO.7)

1. Press * on the main.

2. Press # with registered No. and ID as an administrator.

3. Select users to press #.

4. Select registration to press #.

5. Use F1 or F2 to move, put ID and press # to designate authority It can register

fingerprints, cards and pictures to put a button.

6. Enter fingerprint when a sensor light comes. *It totally registers fingerprint for 3 times

and it would move to previous menu to press *If it finishes fingerprint registration.

7. A card that would use for enter/exit should be read if puts on a screen and press #

to register a card.

8. Register to press # after shooting button for a photo.

9. Go back to a main menu to press F4 if all procedures are clear.

- Keep out of direct sunlight and heat radiation sources.

- Shall not be exposed to dripping or splashing and no objects filled with

liquid such as vases, shall be placed on the products.

- When cleaning, do not use liquid solvent or wet cloth. Wipe with soft cloth.

- Never disassemble or modify this device in any way. (COMMAX Co., Ltd is

not liable for problems caused by unauthorized modification or attempted

repair )

- Do not install this device near by TV, monitor or magnetic interference.

- If the product fails to operate normally, contact the authorized dealer or

service center.

Commax IDentry-T45 Owner's manual

Commax IDentry-T45 Owner's manual

Commax IDentry-T45 Owner's manual

Related papers

Other documents