Boss Audio Systems 775DI User manual

10R-030667

775DI

AM/FM Receiver with universal docking cradle for iPod, iPhone

USER’S MANUAL

CONTENTS

Installation

To support the unit

Detaching and attaching the front panel

Cleaning the connector

Wire Connection

Location of parts and controls

General operations

Using the RDS function

How to select MP3/WMA ﬁles

Playing back USB device / Connect iPod/iPhone

Playing back SD/MMC card

Reset

Troubleshooting

Speciﬁcations

Before installing your new AM/FM Receiver, please review the

items below carefully.

Use only the installation parts and hardware provided with the unit to ensure

proper installation. Using other parts can cause malfunction and possible damage

to your AM/FM receiver.

affect performance.

INSTALLATION

PRECAUTIONS

• Installtheunitinanideallocationwhereitwillnotinterferewithnormaldrivingprocedures.

• Donotinstalltheunitinaplacewhereitwillbeexposetohightemperaturesordirectsunlight,or

whereitwillbepronetodirt,dust,moistureoreexcessivevibration.

• Useonlythesuppliedmountinghardwareforasafeinstallation.

• Removerstthefrontpanelbeforemountingtheunit.

NOTE:Donotinstalltheunitsothatitwillbetiltedatmorethan30°upward.

182mm

53mm

TAP

Bend these

claws,ifnecessay

Release screw and

bracket

NOTE: Securethereleasekeyinasafeandconvenientplaceforfutureuseinremovingtheunitfromthecar.

TO SUPPORT THE UNIT

Detaching and attaching the front panel

Thefrontpanelofthisunitcanbedetachedinordertopreventtheunitfrombeingstolen.

Beforedetachingthefrontpanel,turnothepowerrstbypressingthe

Then press the

buttonanddetachthepanelbypullingittowardsyouasillustrated.

Notes:

• Whenattachingthefrontpaneltotheunit,carefullypressthepanellightlyagainsttheunit.Exces-

siveforcemaydislodgetheunitandcausesomemalfunction.

• Whenyoucarrythefrontpanelwithyou,putitinthesuppliedfrontpanelcase.

1.UNIT

2.RELEASECASE

3.DASHBOARD

4.HEXNUT

5.LOCKWASHER

6.PLAINWASHER

7.CARBODY

8.REARSUPPORTSTRAP

9.TAPPINGSCREW

10.M5X15HEXBOLT

Dashboard

< 10°

Cleaning the connector

Theunitmaynotfunctionproperlyiftheconnectorsbetween

theunitandthefrontpanelarecontaminatedwithdirt.Inorder

topreventthisfromhappening,detachthefrontpanelbypress-

ing the

buttonandcleantheconnectorfromtimetotime.

Clean the connector with a cotton swab together with contact

cleanerasillustrated.Besuretocleanthemcarefullypinbypin

andmakesurenottodamagetheconnectingpoints.

WIRE CONNECTION

RCA Jack Line Out:

Red (right) White (left)

Subwoofer:Orange

USB Drive: Black

Connect USB Drive /

Use Adaptor Connect iPod/iPhone

Maintenance

FUSE REPLACEMENT

Ifthefuseblows,checkthepowerconnectionandreplacethefuse.Ifthefuseblowsagainafterthe

replacement,theremaybeaninternalmalfunction.Inthiscase,consultyournearestrepairingcenter.

Warning

Usethecorrectamperefortheuseineachlead.Improperuseofsuchamperesmaycauseseriousdamage

totheunit.

Cotton Swab

Rear of

front panel

Main unit

GREY +

GREY/BLACK –

FRONT

RIGHT

SPEAKER

VIOLET +

VIOLET/BLACK –

REAR

RIGHT

SPEAKER

FRONT

LEFT

SPEAKER

REAR

LEFT

SPEAKER

+ WHITE

– WHITE/BLACK

+ GREEN

– GREEN/BLACK

ISO A/B PLUG

AUTO ANTENNA

OUTPUT

BLUE

IGNITION SWITCH (12 V)

RED

CONSTANT

12 VOLTS

YELLOW

BLACK

GROUND (–)

L (WHITE)

LINE OUT

R (RED)

ISO CONNECTOR

FUSE 10A

ANTENNA

CONNECTOR

SUBWOOFER

CONNECT USB DRIVE

ADAPTOR

CONNECT iPod/iPhone

Location of Parts and Controls

1. POWERON/OFF( )

2. FUNCTIONSELECTBUTTON:

 VOLUME/BASS/TREBLE/BALANCE/FADER/

without RDS (for USA AREA):BEEP/TADJTIME/AUDIODSP/AREA

RDS (for EUROPE AREA):TASEEK/PISOUND/RETUNE/MASKDPI/

EON/BEEP/TAVOL/ADJTIME/AUDIODSP/AREA

3. TURNVOLLEFTORRIGHTTOADJUSTBASS/TREBLE/BALANCE/

FADER

4. PRESETSTATIONS(1,2,3,4,5,6)

5. STEREO/MONO(ST)/

‘AF’function(ALTERNATIVEFREQUENCIES)(AF)

6. EQUALIZER(EQ)/

 ‘TA’function(TRAFFICANNOUNCEMENT)(TA)

7. LOCAL/DISTANT(LOC)/

 ‘PTY’function(PROGRAMTYPE)(PTY)

8. DISPLAYBUTTON(DISP)

9. MODE/SUBWOOFERBUTTON(MD/SUB)

10.BAND/LOUDNESSBUTTON(BD/LD)

11.AUTOMATICORMANUALTUNING

 (FREQUP

ORFREQDOWN /TRACK/SEARCH)

12.AUTOSEEKSEARCHTUNING(A/PS)

13.‘SCAN’AUTOMATICTUNINGCONTROL(SCAN)

14.MUTEBUTTON(MUTE)

15.LCDDISPLAY

16.OPENPANELRELEASEBUTTON(

)

17.PAUSEBUTTON

18.REPEATBUTTON

19.INTROBUTTON(PreviewallTracks)

20.RANDOMBUTTON

21,22.SEARCHPREVIOUS/NEXTFOLDER

23.FRONTAUXIN

24.USBTUNETRAY

25.SD/MMCCARDSLOT

26.RESET

BD/LD

A/PS

DISP

LOC

PTY

MD/SUB

MUTE SCAN123456

775DI

MODE

TUNE/SEEK

VOL

ENTER

SEL

DISP

BAND

LOUD

RPT

INT

MP3

AS/PS

PAU

FL-

FL+

RDM

1 11 3 2 8 5 6 15 16

12 9 14 17 1918 20 21 22 13 23710

(1-6)

RESET

2 93

1921

17 18

(1-6)

2624 25

BD/LD

A/PS

DISP

LOC

PTY

MD/SUB

MUTE SCAN123456

775DI

BD/LD

A/PS

DISP

LOC

PTY

MD/SUB

MUTE SCAN123456

775DI

MODE

TUNE/SEEK

VOL

ENTER

SEL

DISP

BAND

LOUD

RPT

INT

MP3

AS/PS

PAU

FL-

FL+

RDM

1 11 3 2 8 5 6 15 16

12 9 14 17 1918 20 21 22 13 23710

(1-6)

RESET

2 93

1921

17 18

(1-6)

2624 25

BD/LD

A/PS

DISP

LOC

PTY

MD/SUB

MUTE SCAN123456

775DI

BD/LD

A/PS

DISP

LOC

PTY

MD/SUB

MUTE SCAN123456

775DI

MODE

TUNE/SEEK

VOL

ENTER

SEL

DISP

BAND

LOUD

RPT

INT

MP3

AS/PS

PAU

FL-

FL+

RDM

1 11 3 2 8 5 6 15 16

12 9 14 17 1918 20 21 22 13 23710

(1-6)

RESET

2 93

1921

17 18

(1-6)

2624

BD/LD

A/PS

DISP

LOC

PTY

MD/SUB

MUTE SCAN123456

775DI

BD/LD

A/PS

DISP

LOC

PTY

MD/SUB

MUTE SCAN123456

775DI

MODE

TUNE/SEEK

VOL

ENTER

SEL

DISP

BAND

LOUD

RPT

INT

MP3

AS/PS

PAU

FL-

FL+

RDM

1 11 3 2 8 5 6 15 16

12 9 14 17 1918 20 21 22 13 23710

(1-6)

RESET

2 93

1921

17 18

(1-6)

2624

BD/LD

A/PS

DISP

LOC

PTY

MD/SUB

MUTE SCAN123456

775DI

HOW TO OPERATE THE REMOTE CONTROL

Installing the battery

Slidethetrayoutfromthebackoftheremotecontrolandinsertbatterywith

the(+)andminus(-)polespointingintheproperdirection.

•Whenuseforthersttime,pulloutthelmprotrudingthetray.

CAUTIONS

•Removebatteryiftheremotecontrolisnotusedforamonthorlonger.

•Donotstorebatterywithmetallicmaterials.

•Intheeventofbatteryleakage,replacetheoldbatterywithanewone.Cleanrstthesurfaceof

theremotecontrolincludingthecompartmentofthebattery.

•Whendisposingofusedbatteries,makesurethatyoucomplywithgovernmentregulationsand

environmentalsafetyproceduresinyourarea.

Using the remote control

Pointtheremotecontrolinthedirectionofthefrontpaneltooperate.

IMPORTANT

•Donotstoretheremotecontrolinhightemperaturesordirectsunlight.

GENERAL OPERATIONS

1. POWER

By pressing

,theunitisswitchedon.Pressandholdagaintoturnounit.

2. SELECT BUTTON

3. VOLUME KNOB (Turn left or right to adjust)

 Instandardoperation,theVOLUMEcontrol(3)isforsettingthevolume.

 PresstheSELECTbutton(2)onceorseveraltimes,tochangetheparametersBAS(basscontrol),TRB

(treblecontrol),BAL(balancecontrol)andFAD(fadercontrol)byturningtheVOLUMEcontrol(3)

1 2 3 4 5

SEL SEL SEL SEL SEL

 Fig.1Selectionofsoundcontrolfunctions

 1.VOL2.BAS3.TRB4.BAL5.FAD

Without RDS (for USA Area): Press and hold VOLtoadjustBEEP/TADJTIME/AUDIODSP/AREA

BEEP MODE (2)

PresstheVOLknobagain(formorethan2seconds)toactivateSelectingmodeforBEEP:

2 sec.

SEL

BEEP

2nd / OFF

VOL

2 sec.

BEEP

SEL

FLAT / POP / ROCK / CLASSICALDSP

SEL

ADJ

VOL

2 sec.

BEEP

SEL

DSP AREA USA/EUR

SEL

AREA

SEL

ADJ

VOL

2 sec.

BEEP

SEL

ADJ

to set hourto set minute

VOL

2nd

Button sound is triggered by secondary button functions (hold button down for a while)

OFF Buttonsoundiso

ADJUST TIME (2)

PresstheVOLknobagain(formorethan2seconds)toactivateSelectingmodeforADJUSTTIME:

2 sec.

SEL

BEEP

2nd / OFF

VOL

2 sec.

BEEP

SEL

FLAT / POP / ROCK / CLASSICALDSP

SEL

ADJ

VOL

2 sec.

BEEP

SEL

DSP AREA USA/EUR

SEL

AREA

SEL

ADJ

VOL

2 sec.

BEEP

SEL

ADJ

to set hourto set minute

VOL

 TurnVOLknobclockwisetosethoursandcounterclockwisetosetminutes.

AUDIO DSP CONTROLS (2)

 PresstheVOLknobagain(formorethan2seconds)toactivateSelectingmodeforDSP:

2 sec.

SEL

BEEP

2nd / OFF

VOL

2 sec.

BEEP

SEL

FLAT / POP / ROCK / CLASSICALDSP

SEL

ADJ

VOL

2 sec.

BEEP

SEL

DSP AREA USA/EUR

SEL

AREA

SEL

ADJ

VOL

2 sec.

BEEP

SEL

ADJ

to set hourto set minute

VOL

USA/EUROPE FREQUENCY TUNING (2)

 This unitsupports boththe USA andEUROPE radiofrequenciestuning. TurnVOL knobto adjust

betweenthetwofrequencies.

2 sec.

SEL

BEEP

2nd / OFF

VOL

2 sec.

BEEP

SEL

FLAT / POP / ROCK / CLASSICALDSP

SEL

ADJ

VOL

2 sec.

BEEP

SEL

DSP AREA USA/EUR

SEL

AREA

SEL

ADJ

VOL

2 sec.

BEEP

SEL

ADJ

to set hourto set minute

VOL

USING THE RDS FUNCTION

What is RDS?

TheRDS(RadioDataSystem)isadigitalinformationsystemdevelopedbytheEBU(EuropeanBroad-

castUnion).Piggy-backedonnormalFMbroadcasts,RDSoersavarietyofinformationservicesand

automaticretuningfunctionsforRDS-compatiblecarstereos.

In1988,RDSbecameavailableintheUnitedKingdom,France,WestGermany,IrelandandSweden.

TesttransmissionsarebeingconductedinmanyotherEuropeancountries.ItisexpectedthatRDS

willbeavailableinmostwesternEuropeancountriesinthenearfuture.

RDS (for European Broadcast Union Area): Press and hold VOLtoadjustTASEEK/PISOUND/RETUNE/

MASKDPI/EON/BEEP/TAVOL/ADJTIME/AUDIODSP/AREA

SEL

2 sec.

SEL

BEEP

SEL

RETUNE MASK

SEL

DSP

SEL

AREA

SEL

ADJ

SEL

TA VOL

SEL

EON

SEEK/ALARM (

turnVOLknobtoselectTASEEK/TAALARM)

TA SEEK mode:WhennewlyturnedstationdoesnotreceiveTPinformationfor5sec.,theradio

retunestonextstationwhichhasnotthesamestation(PI)asthelaststation,buthastheTPinforma-

tion.

 InTAseekmode,thecurrentstationcanbechangedtothecompletelydierentstationbecausethe

unitsearchesTPstationwhentheeldstrengthofthecurrentstationisveryweak,orthecurrent

stationhasnoTPsignal.

TA ALARM mode: Anyautomaticretunemodeisnotactivated,justcanhearBeepsound.

PI SOUND (

turnVOLknobtoselectPISOUND/PIMUTE)

Actionwhen2stationswithdierentprogrammeidentication(PI)codesareonthesamefrequency:

SOUND: The radio switches to the new channel for a few seconds and then switches back again

MUTE:Theradioismuted

RETUNE L/S (

turnVOLknobtoselectRETUNEL/RETUNES)

RETUNE L:Select90secondsastheinitialtimeofautomaticTAsearch.

RETUNE S:Select30secondsasinitialtime.

MASK DPI/ALL (

turnVOLknobtoselectMASKDPI/MASKALL)

MASK DPI: maskedonlytheAFwhichhasdierentPI.

MASK ALL: maskedtheAFwhichhasdierentPIandNORDSsignalwitheldstrength.

EON (

turnVOLknobtoselectEONON/EONOFF)

 SelectedEONcondition,ONorOFF.

BEEP (

turnVOLknobtoselectBEEP2nd/BEEPOFF)

ALL: Buttonsoundisonpermanently

2nd:

Button sound is triggered by secondary button functions (hold button down for a while)

OFF: Buttonsoundiso

TA VOL (

turnVOLknobtoselectTAVOLON/TAVOLOFF)

TracAnnouncementVolume

ADJ (

turnVOLknobtoadjustTIME)

DigitalClock.Toadjust,turnVOLknobtorightforhoursandturnVOLknobtoleftforminutes.

DSP Modes (

turnVOLknobtoselectAUDIODSPmodes)

CLASSIC,ROCK,POP,FLAT,NONE

USA/EUROPE FREQUENCY TUNING (

turnVOLknobtoselectwithoutRDS/RDS)

 This unitsupports boththe USA andEUROPE radiofrequenciestuning. TurnVOL knobto adjust

betweenthetwofrequencies.

4. PRESET STATIONS (1-6)

 Sixnumberedpresetbuttonsstoreandrecallstationsforeachband.

Storing a station:

 1.Selectaband(ifneeded)

 2.Selectastation

 3.Holdapresetbuttonlongerthanonesecond.Presetstationnumberappearsinthedisplaywhen

stationissaved.

Recall a station:

 1.Selectband(ifneeded)

 2.Pressapresetbuttonforlessthanonesecondtoselectstoredstation.

Note: This unit is equipped with built-in memory I.C. (Integrated Circuits) to save user settings such

as tuner preset stations and audio control settings. To cancel these settings, switch to Radio mode,

press and hold button “1” for 2 seconds (do not release button) followed by pressing MD button.

Unit will automatically restart after 5 seconds.

5. STEREO/MONO BUTTON (ST)

Press STbuttontoswitchbetweenstereoandmonosoundforFMradioreception.Whenreceptionof

anFMstationisweak,listeningqualitycanbeimprovedbyswitchingtomonosound.

‘AF/REG’ function (ALTERNATIVE FREQUENCIES)

 Whenpressedmomentarily,AF/REGswitchingmodeisselected.

 WhenAF/REGswitchingmodeisselected,theradiochecksthesignalstrengthoftheAFallthetime.

Whenpressedlong,itactivatetheregionalmodeON/OFFfunction.

– Regional mode ON:

 AFswitchingorPISEEKisimplementedtothestationwhichhaveallPIcodessameascurrentstation.

REGsegmentisturnedon,inLCDdisplay.

– Regional mode OFF

TheregionalcodeintheformatofPIcodeisignoredwhenAFswitchingorPISEEKisimplemented.

6. EQUALIZER CONTROL (EQ)

Press EQtoselectbetweenO/Pop/Rock/Classic/Flatequalizermodes.

‘TA’ function (TRAFFIC ANNOUNCEMENT)

 Whenpressedmomentarily,itisactivatedasTAmodeonoro

 WhenTAmodeisonandtracannouncementistransmitted

 –WhentheunitisinMP3mode,itwillswitchtoradiomodetemporarily.

 –Ifthevolumelevelwasunderthethresholdpoint,itwillberaisedtothethresholdpoint.

 –WhenTPstationisreceived,TPsegmentisturnedinLCDdisplay.

7. LOCAL/DISTANT BUTTON (LOC)

 PressLocal/Distant(LO/DX)buttonforlisteningtoweakstations.“LOCAL”indicatorwillappearon

thedisplay.Pressthisbuttonagain(Distantmode)fornormaloperation.

‘PTY’ function (PROGRAM TYPE)

 EachpressofPTY button will toggle between PTY Music, PTY Speech and PTY Oﬀ.

When PTY Musicisselected,pressButtons(1-6)fordesiredprogramtypes.Unitautomaticallysearch

forcorrespondingprograms.

 1PopM,RockM 2EasyM,LightM 3Classics,OtherM

 4Jazz,Country 5NationM,Oldies 6FolkM

When PTY Speechisselected,pressButtons(1-6)fordesiredprogramtypes.Unitautomaticallysearch

forcorrespondingprograms.

 1News,Aairs,Info 2Sport,Educate,Drama 3Culture,Science,Varied

 4Weather,Finance,Children 5Social,Religion,PhoneIN 6Travel,Leisure,Document

Tips:

Program Type function is available only in radio FM mode.

Since each button number can store multiple program types, i.e. Button 1 stores Pop and Rock music,

to switch between Pop and Rock music, simply press button 1 repeatedly until the desired program

type shows in display.

8. DISPLAY (DISP)

Press DISPbuttontoswitchbetweendisplayinformationssuchasradiofrequencies,clock,track

andotherinformationsdependingontheplayingMODE.

9. MODE / SUBWOOFER BUTTON (MD/SUB)

 Bypressingthiskey,usercanselectTUNER/USB1/USB2/MMC/SD/AUXmode.

SUBWOOFER:Pressandholdbuttontoengagesubwooferoutput.

10. BAND / LOUDNESS BUTTON (BD/LD)

 EachbandistoggledcyclicallybypressingthiskeyFM1---FM2---FM3---MW(AM)1---MW(AM)2.

LOUDNESS:PressandholdthebuttontoselectLOUDNESSmode.

11. AUTOMATIC OR MANUAL TUNING (FREQ UP

OR FREQ DOWN )

(A) RADIO MODE

 Whenpressedmomentarily,thesekeysareoperatedasMANUALtuningmode.

 Whenpressedlongerthan1sec.,theyoperateasSEEKtuningmode.

(B) MP3/WMA PLAYER MODE

 Whenpressedmomentarily,theyoperateasTRACKUPorTRACKDOWNmode.

 Whenpressedlongerthan1sec.,theyoperateasCUEorREVIEWmode.

12. AUTO SEEK / PRESET SCAN (A/PS)

Preset Scan (PS) -Bypressingshortly,theradioplayseachpresetstationfor5seconds.

Auto Seek (AS)-Bypressinglongerthan1sec,autoseekisactivated.The6strongeststationsare

presetandstoredinthecorrespondingpresetnumber.WhenAutoSeekoperationisnished,the

radioexecutesthepresetscan.

13. ‘SCAN’ AUTOMATIC TUNING CONTROL (SCAN)

 Thisbuttonstartstheauto-scan.Whenastationhasbeenfound,itisplayedfor5secondsandthen

theauto-scaniscontinued.Pressthebuttonagaintostoptheauto-scantolistentothecurrently

playedstation.

14. MUTE BUTTON

 Pressthisbuttontosilentthesoundatonce.Pressagaintoreturntopreviousvolumelevel.

15. LCD DISPLAY

 TheLiquidCrystalDisplaywilldisplaythecurrentstateoftheunit.

16. OPEN THE FRONT PANEL (

)

Press

buttonandthefrontpanelwillopen.

MP3/WMA CONTROL LOCATION OF PARTS

TRACK/SEARCH BUTTON (11)

FORWARD AND REVERSE TRACK SEARCH (or changing songs)

PresstheSKIPbutton(

or )duringplaytogotothedesiredtrack(song).

....REVERSE ....FORWARD

PressandholdtheSKIPbutton(

or )duringplaytoscanathighspeed.Whenthedesiredmusic

sectionisfound,releasethebutton.Normalplaywillresume.

17. PAUSE BUTTON

 During“PLAY”,press(17)‘PAU’buttonto“PAUSE”.Pressitagaintoresumeplay.

18. REPEAT BUTTON

 Whenthisbuttonispressed,‘RPT’indicationisdisplayedandplayoftheselectedtrackwillbecon-

tinuallyrepeateduntiltheTrackrepeatmodeiscancelledbypressing‘RPT’buttonagain.

19. INTRO BUTTON (Preview all Tracks)

 Whenthisbuttonispressed,‘INT’indicationisdisplayedandtherstseveralsecondsofeachtrack

areplayed.Pressagaintostopintroandlistentotrack.

20. RANDOM BUTTON

Whenthisbuttonispressed,‘RDM’indicationisdisplayedandeachtrackareplayedinrandominstead

ofnormalprogression.TocancelRANDOMmode,press‘RDM’buttonagain.

21, 22. SEARCH PREVIOU / NEXT FOLDER: (In case of MP3/WMA ﬁles)

Pressthesebuttonstosearchprevious/nextfolder.

NOTE: These buttons (17 to 22) are available only in MP3 and USB mode.

HOW TO SELECT MP3/WMA FILES

Searching by Track:

• Press“A/PS”,digitstartsblinking.

• TurnVOLtorightorleftuntilthedesiredtracknumbershowsthenpressVOLknob.

• Songnumberyouselectedwillstarttoplay.

Searching by Folder:

• Press“A/PS”twice.

• TurnVOLtorightorlefttoselectfoldernamethenpressVOLknob.

• TurnVOLtorightorlefttoselectletoplaythenpressVOLknobtostartplayback.

23. Connecting AUX IN

Anexternalaudiosource(e.g.portableMP3player)canbeconnectedtotheAUXINsockettobeplayed

backbythevehicleloudspeakers.

1. ConnecttheAUXINsocketwiththeaudiooutputoftheexternaldevice.

2. PressMDbuttonandswitchtoAUXmode.

PLAYING BACK USB DEVICE / CONNECT iPod/iPhone

A USB device can be connected to theinternal/external or bothUSB connectors. PressMD to select

USB1(internal),USB2(external).

Playing back via the USB (internal) connector

1. Press

buttonandthefrontpanelwillopen.

2. PressPUSHOPENontheTUNETRAY.TheTUNETRAYopensslowly.

3. ConnecttheUSBdevicetotheUSBconnector.orUseadaptorConnecttoUSBportforplayingiPod/

iPhone.

4. SlideintheTUNETRAYbypressingPUSHCLOSEontheTUNETRAYuntilitlocksshut.

5. Closethefrontpanel.

6. Theplayerautomaticallyswitchestotheinputusedandstartsplayback.

7. Seethesectiononoperationscommonforaudioles.

Playing Songs in iPod

1. PressMDtoselectUSB1.

2. PressA/PS.

3. RotateVOLtoselectPLAYLIST–ARTISTS–ALBUMS–SONGS–GENRES-COMPOSER

4. PressBD/LD.

IfyouareawareonhowtouseiPOD,thewaytousethecarstereofeatureisbasically

justthesame.Takenoteoftheequivalentkeyfunctionbelow.

Car Stereo iPOD Functions

 RotateVOLknob RotateCLICKWHEEL Up/downcategory/lebrowsing

 PressBD/LDbutton PressSELECTbutton Selectingacategory/Playsong

CarStereoandiPODequivalentkeyfunction

Note: Please refer to your iPOD user’s manual for operating instructions.

Press A/PS to go back to Main Menu.

Note:•supportiPodClassic•iPodnano2,3,4,5,6•iPodtouch1,2,3•iPhone,3G,3GS,4

PLAYING BACK SD/MMC CARD

< 10°

1. Press buttonandthefrontpanelwillopen.

2. Detachthefrontpanel.

3. InsertSD/MMCintothememorycardreader.

4. Theplayerautomaticallyswitchestotheinputusedandstartsplayback.

5. Seethesectiononoperationscommonforaudiolesonhowtocontrolmemorycardplayback.

Note:

- Due to the great variety of devices with USB and SD/MMC card interfaces that sometimes have

manufacturer-speciﬁc functions, we cannot guarantee that all media will be recognized and that all

operational functions will be available with this device.

- You cannot operate USB hard drives on the device.

RESET

Thisbuttonisbehindthefrontpanelandresetsallthesettingstotheoriginalsettingsthatweremade

inthefactory.Pressthisbuttoninthefollowingcases:

- whenyouhavecompletedtheinstallationandconnection

- when the display shows undeﬁned characters

Note: You have to detached the front panel and use a sharp object to press the “Reset” button.

RESET

Speciﬁcations

775DI

AM/FM Receiver with with universal docking cradle for iPod, iPhone

CD/MP3 PLAYER

Signal to noise ratio >60dB

Channel separation >50dB(1kHz)

Frequency response 20Hz-20kHz

RADIO

FM Section:

Frequency range 87.5-107.9MHz(America),87.5-108MHz(Europe)

Channel step 200kHz(USA),50kHz(Europe)

Sensitivity 2.8µV

Stereo separation 30dB

Signal to noise ratio 50dB

MW(AM) Section:

Frequency range 530-1710KHz(America),522-1620KHz(Europe)

Usable sensitivity 32dBµV

TONE CONTROLS

Bass (at 100Hz) +/-10dB

Treble (at 10kHz) +/-10dB

LINE-OUT

Output 1.5V(max.)

Impedance 10kOhm

AMPLIFIER

Maximum output power 80wattsx4channels

GENERAL

Power supply 12VDC(10.8-15.6Vallowable)

Speaker impedance 4or8Ohm

Fuse 10A

Instructions on environment protection

Do not dispose or throw away this product in the usual household garbage at the end of its life-

cycle.Themethodofdisposalofthisproductisproperlyinscribedinthismanual.Thematerial

usedarerecyclable,andbyrecyclingthisproduct,youarehelpingprotectourenvironment.

Pleaseinquireatthecommunityadministrationfortheauthorizeddisposallocation.

Boss Audio Systems 775DI, MP3/AM/FM Receiver User manual

Related papers

Other documents