DECAL PLACEMENT
10
Flat Black
Light Gull Gray
Dark Gray
Aluminum
Green
Insignia Red
Steel
Yellow
Blue Angel Blue
Orange
Red
Gloss White
Olive Drab
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Noir mat
Gris clair
Gris foncé
Aluminium
Vert
Rouge emblemé
Acier
Jaune
Blue angélique
Orange
Rouge
Blanc brillant
Gris vert
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulle was
d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
BLUE ANGELS' A-4 SKYHAWK
KIT 5310 85531000200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85531000200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
Kit 5310 - Page 8
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* DECAL
* DECAL COMANIE
* ASSEMBLY CAUTION
*ATTENTION D ASSEMBLEE
* OPTIONAL PARTS
* PIECES EN OPTION
* REPEAT PROCEDURE
* R E P E T E Z L E P R O C E D E
`` ` ` `
The A-4 Skyhawk was designed as a small
light weight jet attack aircraft capable of oper-
ating from aircraft carriers. The Skyhawk was
used extensively during the war in Vietnam
where it gained a reputation for being rugged
and reliable. A-4's were also used by the Blue
Angels flight demonstration team. The Blue
Angels are well known the world over for their
impressive performances of precision aero-
batics. Flying in tight formation, these four
outstanding U.S. Navy flyers captivate their
audiences with breath-taking maneuvers.
Your Monogram model features an open or
closed canopy with detailed cockpit and pilot,
two optional external fuel tanks, center bomb
pylon with six bombs and two wing mounted
missiles and decals to build any one of the four
aircraft from the Blue Angels team of 1978 or
A-4E Skyhawk of LVDR John S. McCain,
VA-45 Klansmen, USS Forestal, June 1967.
COCKPIT / FUSELAGE ASSEMBLY
1DECAL PLACEMENT
9
39
PILOT ARM
40
PILOT
22
CONTROL
STICK
DARK GRAY
20
NOSE GEAR
WELL
WHITE
23
INSTRUMENT PANEL
DARK GRAY WITH BLACK INSTRUMENTS
21
COCKPIT
DARK GRAY WITH
BLACK INSTRUMENTS
44
RIGHT
FUSELAGE
1
LEFT
FUSELAGE
11
SMALL FAIRING
31
AVIONIC PACK
RIGHT HALF
55
AVIONIC PACK
LEFT HALF
27
LEFT
INTAKE
4
DECAL
3
DECAL
1
DECAL
2
DECAL
53
RIGHT
INTAKE
FLAT BLACK
FLAT BLACK
LIGHT GRAY
(STRAPS)
DARK GRAY
(BOTH SIDES)
Kit 5310 - Page 2 Kit 5310 - Page 7
PAINT NOTE:
PILOT - WHITE OR DARK GREEN HELMET WITH
BLACK TRIM, OLIVE DRAB SUIT, DARK GRAY MASK
AND HOSE, BLACK BOOTS, LIGHT GRAY CHUTE
STRAPS WITH SILVER BUCKLES, BLACK GLOVES.
BLUE ANGELS VERSION
WING ASSEMBLY
2
MAIN WHEEL ASSEMBLY
3
Kit 5310 - Page 3Kit 5310 - Page 6
38
FUEL TANK TOP
WHITE
58
FUEL TANK BOTTOM
WHITE
26
FUEL TANK PYLON
WHITE
36
BOMB HALF
WITH FINS
OLIVE DRAB
57
BOMB HALF
OLIVE DRAB
33
BOMB RACK
WHITE
37
MISSILE FIN
WHITE
35
MISSILE HALF
WITH FINS
WHITE
56
MISSILE HALF
WHITE
37
MISSILE FIN
WHITE
2
WING BOTTOM
45
RIGHT
WING TOP
3
LEFT
WING TOP
5
LEFT
WING SLAT
UNDERSIDE RED
14
MAIN WHEEL
FLAT BLACK
14
MAIN WHEEL
FLAT BLACK
59
WING ANTENNA
WHITE
8
RIGHT
MAIN GEAR STRUT
WHITE
50
LEFT
MAIN GEAR STRUT
WHITE 51
RIGHT
RETRACTION STRUT
WHITE
9
LEFT
RETRACTION STRUT
WHITE
47
RIGHT
WING SLAT
UNDERSIDE RED
WHITE
ALUMINIUM
ALUMINIUM
WHITE
32
MISSILE
PYLON
WHITE
32
MISSILE
PYLON
WHITE
ARMAMENT ASSEMBLY
8
DOOR / FLAP ASSEMBLY
4
NOSE WHEEL ASSEMBLY
5
TAIL ASSEMBLY
6
CANOPY ASSEMBLY
7
Kit 5310 - Page 4 Kit 5310 - Page 5
ANGLE OF FLAPS
ANGLE OF AIR BRAKES
CLOSED
OPEN
62
LANDING LIGHT
CLEAR
16
RIGHT
MAIN WHEEL DOOR
16
RIGHT
MAIN WHEEL DOOR
52
LEFT
MAIN WHEEL DOOR
4
LEFT
WING FLAP
RED
(INSIDE SURFACE)
61
RIGHT
MAIN STRUT DOOR
19
LEFT
MAIN STRUT DOOR
46
RIGHT
WING FLAP
RED
(INSIDE SURFACE)
7
LEFT
CANNON
STEEL
49
RIGHT
CANNON
STEEL
34
ECM
34
ECM
34
ECM'S
13
YOKE
WHITE
WHITE
15
NOSE WHEEL
FLAT BLACK
10
NOSE GEAR STRUT
WHITE
12
NOSE GEAR
RETRACTION STRUT
WHITE
17
NOSE GEAR DOOR
RED
(INSIDE SURFACE)
28
LEFT
AIR BRAKE
RED
(INSIDE SURFACE)
29
AIR BRAKE ACTUATOR
ALUMINUM
29
AIR BRAKE ACTUATOR
ALUMINUM
6
LEFT
HORIZONTAL
STABILIZER
ALUMINUM
48
RIGHT HORIZONTAL
STABILIZER
ALUMINUM
25
EXHAUST
NOZZEL
ALUMINUM
61
TAIL STAND
CLEAR
30
ARRESTOR
HOOK
FLAT BLACK
(INSIDE)
FLAT BLACK
54
RIGHT
AIR BRAKE
RED
(INSIDE SURFACE)
18
NOSE STRUT DOOR
RED
(INSIDE SURFACE)
ALUMINUM
ALUMINUM
64
CANOPY
SHADED AREA
BLUE
FUSELAGE
COLOR
63
WINDSHIELD
SHADED AREA
FUSELAGE COLOR
FLAT BLACK
DARK GRAY
24
REFUELING PROBE
DOOR / FLAP ASSEMBLY
4
NOSE WHEEL ASSEMBLY
5
TAIL ASSEMBLY
6
CANOPY ASSEMBLY
7
Kit 5310 - Page 4 Kit 5310 - Page 5
ANGLE OF FLAPS
ANGLE OF AIR BRAKES
CLOSED
OPEN
62
LANDING LIGHT
CLEAR
16
RIGHT
MAIN WHEEL DOOR
16
RIGHT
MAIN WHEEL DOOR
52
LEFT
MAIN WHEEL DOOR
4
LEFT
WING FLAP
RED
(INSIDE SURFACE)
61
RIGHT
MAIN STRUT DOOR
19
LEFT
MAIN STRUT DOOR
46
RIGHT
WING FLAP
RED
(INSIDE SURFACE)
7
LEFT
CANNON
STEEL
49
RIGHT
CANNON
STEEL
34
ECM
34
ECM
34
ECM'S
13
YOKE
WHITE
WHITE
15
NOSE WHEEL
FLAT BLACK
10
NOSE GEAR STRUT
WHITE
12
NOSE GEAR
RETRACTION STRUT
WHITE
17
NOSE GEAR DOOR
RED
(INSIDE SURFACE)
28
LEFT
AIR BRAKE
RED
(INSIDE SURFACE)
29
AIR BRAKE ACTUATOR
ALUMINUM
29
AIR BRAKE ACTUATOR
ALUMINUM
6
LEFT
HORIZONTAL
STABILIZER
ALUMINUM
48
RIGHT HORIZONTAL
STABILIZER
ALUMINUM
25
EXHAUST
NOZZEL
ALUMINUM
61
TAIL STAND
CLEAR
30
ARRESTOR
HOOK
FLAT BLACK
(INSIDE)
FLAT BLACK
54
RIGHT
AIR BRAKE
RED
(INSIDE SURFACE)
18
NOSE STRUT DOOR
RED
(INSIDE SURFACE)
ALUMINUM
ALUMINUM
64
CANOPY
SHADED AREA
BLUE
FUSELAGE
COLOR
63
WINDSHIELD
SHADED AREA
FUSELAGE COLOR
FLAT BLACK
DARK GRAY
24
REFUELING PROBE
WING ASSEMBLY
2
MAIN WHEEL ASSEMBLY
3
Kit 5310 - Page 3Kit 5310 - Page 6
38
FUEL TANK TOP
WHITE
58
FUEL TANK BOTTOM
WHITE
26
FUEL TANK PYLON
WHITE
36
BOMB HALF
WITH FINS
OLIVE DRAB
57
BOMB HALF
OLIVE DRAB
33
BOMB RACK
WHITE
37
MISSILE FIN
WHITE
35
MISSILE HALF
WITH FINS
WHITE
56
MISSILE HALF
WHITE
37
MISSILE FIN
WHITE
2
WING BOTTOM
45
RIGHT
WING TOP
3
LEFT
WING TOP
5
LEFT
WING SLAT
UNDERSIDE RED
14
MAIN WHEEL
FLAT BLACK
14
MAIN WHEEL
FLAT BLACK
59
WING ANTENNA
WHITE
8
RIGHT
MAIN GEAR STRUT
WHITE
50
LEFT
MAIN GEAR STRUT
WHITE 51
RIGHT
RETRACTION STRUT
WHITE
9
LEFT
RETRACTION STRUT
WHITE
47
RIGHT
WING SLAT
UNDERSIDE RED
WHITE
ALUMINIUM
ALUMINIUM
WHITE
32
MISSILE
PYLON
WHITE
32
MISSILE
PYLON
WHITE
ARMAMENT ASSEMBLY
8
COCKPIT / FUSELAGE ASSEMBLY
1DECAL PLACEMENT
9
39
PILOT ARM
40
PILOT
22
CONTROL
STICK
DARK GRAY
20
NOSE GEAR
WELL
WHITE
23
INSTRUMENT PANEL
DARK GRAY WITH BLACK INSTRUMENTS
21
COCKPIT
DARK GRAY WITH
BLACK INSTRUMENTS
44
RIGHT
FUSELAGE
1
LEFT
FUSELAGE
11
SMALL FAIRING
31
AVIONIC PACK
RIGHT HALF
55
AVIONIC PACK
LEFT HALF
27
LEFT
INTAKE
4
DECAL
3
DECAL
1
DECAL
2
DECAL
53
RIGHT
INTAKE
FLAT BLACK
FLAT BLACK
LIGHT GRAY
(STRAPS)
DARK GRAY
(BOTH SIDES)
Kit 5310 - Page 2 Kit 5310 - Page 7
PAINT NOTE:
PILOT - WHITE OR DARK GREEN HELMET WITH
BLACK TRIM, OLIVE DRAB SUIT, DARK GRAY MASK
AND HOSE, BLACK BOOTS, LIGHT GRAY CHUTE
STRAPS WITH SILVER BUCKLES, BLACK GLOVES.
BLUE ANGELS VERSION
DECAL PLACEMENT
10
Flat Black
Light Gull Gray
Dark Gray
Aluminum
Green
Insignia Red
Steel
Yellow
Blue Angel Blue
Orange
Red
Gloss White
Olive Drab
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Noir mat
Gris clair
Gris foncé
Aluminium
Vert
Rouge emblemé
Acier
Jaune
Blue angélique
Orange
Rouge
Blanc brillant
Gris vert
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulle was
d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
BLUE ANGELS' A-4 SKYHAWK
KIT 5310 85531000200
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85531000200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
Kit 5310 - Page 8
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* DECAL
* DECAL COMANIE
* ASSEMBLY CAUTION
*ATTENTION D ASSEMBLEE
* OPTIONAL PARTS
* PIECES EN OPTION
* REPEAT PROCEDURE
* R E P E T E Z L E P R O C E D E
`` ` ` `
The A-4 Skyhawk was designed as a small
light weight jet attack aircraft capable of oper-
ating from aircraft carriers. The Skyhawk was
used extensively during the war in Vietnam
where it gained a reputation for being rugged
and reliable. A-4's were also used by the Blue
Angels flight demonstration team. The Blue
Angels are well known the world over for their
impressive performances of precision aero-
batics. Flying in tight formation, these four
outstanding U.S. Navy flyers captivate their
audiences with breath-taking maneuvers.
Your Monogram model features an open or
closed canopy with detailed cockpit and pilot,
two optional external fuel tanks, center bomb
pylon with six bombs and two wing mounted
missiles and decals to build any one of the four
aircraft from the Blue Angels team of 1978 or
A-4E Skyhawk of LVDR John S. McCain,
VA-45 Klansmen, USS Forestal, June 1967.
/
