TSURUMI PUMP HS2.4S Residue Kit Installation guide

Brand
TSURUMI PUMP
Model
HS2.4S Residue Kit
Type
Installation guide

TSURUMI PUMP HS2.4S Residue Kit

The TSURUMI PUMP HS2.4S Residue Kit is a low water level pump down kit that can be used with the Tsurumi HS2.4S Sand/Trash Pump. This kit allows the pump to pump down to a lower water level than the standard strainer stand.

The Residue Kit includes a residue plate, three M8 x 65 hex bolts, three M8 flat washers, and three M8 nylon spacers. The residue plate is installed on the bottom of the pump, and the hex bolts are used to secure it in place. The flat washers are used to provide a level surface for the residue plate, and the nylon spacers are used to retain solids handling capability.

TSURUMI PUMP HS2.4S Residue Kit

The TSURUMI PUMP HS2.4S Residue Kit is a low water level pump down kit that can be used with the Tsurumi HS2.4S Sand/Trash Pump. This kit allows the pump to pump down to a lower water level than the standard strainer stand.

The Residue Kit includes a residue plate, three M8 x 65 hex bolts, three M8 flat washers, and three M8 nylon spacers. The residue plate is installed on the bottom of the pump, and the hex bolts are used to secure it in place. The flat washers are used to provide a level surface for the residue plate, and the nylon spacers are used to retain solids handling capability.

HS2.4S Residue Kit
Installation Guide
MAY2013
The RESIDUE KIT provides a low water level pump down by
simply replacing the standard Strainer Stand of your Tsurumi
HS2.4S Sand/Trash Pump with this Residue Kit.
Residue Kit Installed on
Tsurumi HS2.4S Sand/Trash Pump
w w w . t s u r u m i p u m p . c o m
Tsurumi (America), Inc. • 1625 Fullerton Court, Glendale Heights, IL 60139 • Tel: 888-878-7864 (toll-free)
Check out other Tsurumi Pumps designed fo low-level
pumping and remove standing water from...
Road Construction
Roof Tops
Parking Lots
Basements Sport Facilities
LSC1.4S - Floor Level Drainage Pump
Internal check valve allows LSC pump to hold prime for:
- start-up at any water level
- pump down to any surface
- prevention of back-flow when turned off
LSR2.4S - Ground Level Drainage Pump
Top discharge, angle coupling design allows for:
- continuous operation at low water levels
without overheating motor
- easy change to vertical or horizontal discharge
Step 1:
Remove the strainer stand from
pump by removing the (3) M8
nuts using a 13mm wrench or
socket.
Make sure your Residue Kit has all
components on hand:
• Residue plate
• Hex bolt M8 x 65 (Qty 3)
• Flat washer M8 (Qty 3)
• Nylon Spacer M8 (Qty 3)
Lift the pump assembly from the pump casing / discharge assembly and invert
the pump upside down on a sturdy level surface. Block the pump in place as
illustrated to assure it is stable during installation of the residue plate.
If a suitable size block is not available, the strainer stand may be used to
support the pump.
Replace the pump casing / discharge assembly to
the pump assembly and place either set of (3) flat
washers (for lowest pump down level), or (3)
nylon spacers (to retain solids handling
capability).
<CAUTION> Use the nylon spacer option when
the pump is used on a finished surface or flexible
material such as a swimming pool or pond liner.
Place the residue plate, assuring that the bolt
through-holes are aligned with the washers or
spacers. Install the (3) M8 x 65mm hex bolts
from the Residue Kit as illustrated.
To complete the Residue Kit installation, reinstall
the (3) nuts removed in Step 2, and carefully
return the pump to its upright position.
<CAUTION> When small stones are present, clear
a large area free of stones and place the pump on
a hard level surface (such as a board) to prevent
stones from passing through the pump.
Step 3:
Step 2: Step 4:
Step 5:
Step 6:
  • Page 1 1
  • Page 2 2

TSURUMI PUMP HS2.4S Residue Kit Installation guide

Brand
TSURUMI PUMP
Model
HS2.4S Residue Kit
Type
Installation guide

TSURUMI PUMP HS2.4S Residue Kit

The TSURUMI PUMP HS2.4S Residue Kit is a low water level pump down kit that can be used with the Tsurumi HS2.4S Sand/Trash Pump. This kit allows the pump to pump down to a lower water level than the standard strainer stand.

The Residue Kit includes a residue plate, three M8 x 65 hex bolts, three M8 flat washers, and three M8 nylon spacers. The residue plate is installed on the bottom of the pump, and the hex bolts are used to secure it in place. The flat washers are used to provide a level surface for the residue plate, and the nylon spacers are used to retain solids handling capability.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents