Algo 8039 User guide

Category
Door intercom systems
Type
User guide
8039 SIP Video Intercom (FW version 2.0.1)
8039 SIP Video Intercom
FW Version 2.0.1
Installation & Configuration
Order Codes
8039 SIP Video Intercom
Document 90-00075A
10/31/2019
Page 1
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Table of Contents
IMPORTANT SAFETY INFORMATION......................................................................................................3
OVERVIEW................................................................................................................................................. 6
INTRODUCTION................................................................................................... 6
WHATS NEW (COMPARED TO THE PREVIOUS FIRMWARE V1.5)........................................6
SETUP AND INSTALLATION..................................................................................................................... 7
GETTING STARTED - QUICK INSTALL & TEST...............................................................7
INSTALLATION.................................................................................................... 8
PROGRAMMING AND CONFIGURATION........................................................................8
WIRING CONNECTIONS..........................................................................................9
WEB INTERFACE STATUS AND LOGIN................................................................................................. 11
WEB INTERFACE LOGIN.......................................................................................11
STATUS..........................................................................................................12
STATUS TAB – VIDEO.........................................................................................12
WEB INTERFACE BASIC SETTINGS......................................................................................................13
BASIC SETTINGS TAB – SIP..................................................................................13
BASIC SETTINGS TAB – FEATURES..........................................................................14
BASIC SETTINGS TAB – VIDEO...............................................................................16
BASIC SETTINGS TAB – KEYPAD............................................................................19
BASIC SETTINGS TAB – DOOR CONTROL..................................................................21
BASIC SETTINGS TAB – MULTICAST........................................................................23
WEB INTERFACE ADVANCED SETTINGS............................................................................................. 26
ADVANCED SETTINGS TAB - NETWORK....................................................................26
ADVANCED SETTINGS TAB – ADMIN........................................................................28
ADVANCED SETTINGS TAB – TIME..........................................................................30
ADVANCED SETTINGS TAB – PROVISIONING..............................................................31
ADVANCED SETTINGS TAB – TONES........................................................................33
ADVANCED SETTINGS TAB – ADVANCED AUDIO..........................................................34
ADVANCED SETTINGS TAB – ADVANCED SIP.............................................................35
ADVANCED SETTINGS TAB – ADVANCED MULTICAST....................................................37
WEB INTERFACE SYSTEM..................................................................................................................... 39
SYSTEM TAB - MAINTENANCE...............................................................................39
UPGRADE 8039 SIP VIDEO INTERCOM FIRMWARE......................................................40
SYSTEM – SYSTEM LOG.......................................................................................40
SPECIFICATIONS..................................................................................................................................... 41
8061 IP RELAY CONTROLLER............................................................................................................... 42
TYPICAL 8039/8061 SETUP..................................................................................................................... 43
POE AND RELAY CONNECTIONS ON BACK OF 8061 IP RELAY CONTROLLER:......................43
CONFIGURING THE 8061........................................................................................................................ 44
FCC COMPLIANCE STATEMENT............................................................................................................ 45
Document 90-00075A
10/31/2019
Page 2
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Important Safety Information
Important Safety Information
This product is powered by a certified limited power source (LPS), Power over
Ethernet (PoE); through CAT5 or CAT6 connection wiring to an IEEE 802.3af
compliant network PoE switch. The product is intended for installation indoors or
on outdoor perimeter of a building. If used in an outdoor environment, additional
protective measures must be taken according to the installation manual. All wiring
connections to the product must be in the same building. If the product is installed
beyond the building perimeter or used in an inter-building application, the wiring
connections must be protected against over voltage / transient. Algo recommends
that this product be installed by a qualified electrician.
If you are unable to understand the English language safety information then
please contact Algo by email for assistance before attempting an installation
Consignes de Sécurité Importantes
Ce produit est alimenté par une source d’alimentation limitée certifiée
(alimentation par Ethernet); des câbles de catégorie 5 et 6 joignent un
commutateur réseau à alimentation par Ethernet homologué IEEE 802.3af. Le
produit est conçu pour être installé à l’intérieur ou dans une zone adjacente à un
édifice; selon le manuel d’installation, des mesures de sécurité additionnelles
s’avèrent alors nécessaires. Tout le câblage rattaché au produit doit se trouver
dans le même édifice. Si le produit est installé au-delà du périmètre de l’édifice ou
utilisé pour plusieurs édifices, le câblage doit être protégé des surtensions
transitoires. Algo recommande qu’un électricien qualifié se charge de l’installation
de ce produit.
Si vous ne pouvez comprendre les consignes de sécurité en anglais, veuillez
communiquer avec Algo par courriel avant d’entreprendre l’installation au
Información de Seguridad Importante
Este producto funciona con una fuente de alimentación limitada (Limited Power
Source, LPS) certificada, Alimentación a través de Ethernet (Power over Ethernet,
PoE); mediante un cable de conexión CAT5 o CAT6 a un conmutador de red con
PoE en cumplimiento con IEEE 802.3af. El producto se debe instalar en lugares
cerrados o en el perímetro de un edificio al aire libre. Si se utiliza en un ambiente
al aire libre, se deben tomar medidas de protección adicionales de acuerdo con el
Document 90-00075A
10/31/2019
Page 3
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
manual de instalación. Todas las conexiones cableadas al producto deben estar
en el mismo edificio. Si el producto se instala fuera del perímetro del edificio o se
utiliza en una aplicación en varios edificios, las conexiones cableadas se deben
proteger contra sobretensión o corriente transitoria. Algo recomienda que la
instalación de este producto la realice un electricista calificado.
Si usted no puede comprender la información de seguridad en inglés,
comuníquese con Algo por correo electrónico para obtener asistencia antes de
intentar instalarlo: [email protected].
Wichtige Sicherheitsinformationen
Dieses Produkt wird durch eine zertifizierte Stromquelle mit begrenzter Leistung
(LPS – Limited Power Source) betrieben. Die Stromversorgung erfolgt über
Ethernet (PoE – Power over Ethernet). Dies geschieht durch eine Cat-5-
Verbindung oder eine Cat-6-Verbindung zu einer IEEE 802.3af-konformen
Ethernet-Netzwerkweiche. Das Produkt wurde konzipiert für die Installation
innerhalb eines Gebäudes oder außerhalb eines Gebäudes. Bei der Anwendung
außerhalb eines Gebäudes müssen zusätzliche Schutzmaßnahmen gemäß der
Gebrauchsanweisung durchgeführt werden. Alle Kabelverbindungen zum Produkt
müssen im selben Gebäude bestehen. Wenn das Produkt jenseits des Gebäudes
oder für mehrere Gebäude genutzt wird, müssen die Kabelverbindungen vor
Überspannung und Spannungssprüngen geschützt werden. Algo empfiehlt das
Produkt von einem qualifizierten Elektriker installieren zu lassenv.
Sollten Sie die englischen Sicherheitsinformationen nicht verstehen, kontaktieren
Sie bitte Algo per Email bevor Sie mit der Installation beginnen, um Unterstützung
zu erhalten. Algo kann unter der folgenden E-Mail-Adresse erreicht werden:
安全须知
本产品由认证的受限电源(LPS),以太网供电(PoE),通过 CAT5 或 CAT6 线路
联接至 IEEE 802.3af 兼容的 PoE 网络交换机供电。本产品适用于室内或建筑物周边
安装。如用于室外环境,必须按照安装手册采用附加的保护措施。所有联接本产品
的线路必须源自同一建筑物。本产品如需用于超出建筑物周边范围或跨建筑物的安
装,线路联接部分必须有过压和瞬态保护。Algo 建议本产品由专业电工安装。
如果您对理解英文版安全须知有问题,安装前请通过电子邮件和 Algo 联
Document 90-00075A
10/31/2019
Page 4
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
EMERGENCY COMMUNICATION
If used in an emergency communication application, the 8039 SIP Video Intercom
should be routinely tested. SNMP supervision is recommended for assurance of
proper operation. Contact Algo for other methods of operational assurance
including the use of the integrated microphone for automated “sound to air”
acoustic testing.
WET OR OUTDOOR ENVIRONMENTS
The 8039 SIP Video Intercom is intended for indoor or outdoor locations and may
be subjected to spray or weather, provided the rear wiring cavity is properly sealed
to prevent water ingress.
Gaskets included with the 8039 SIP Video Intercom may be effective against water
ingress on some, but not all surfaces in which case additional protective measures
must be taken such as a perimeter sealant.
CAT5 or CAT6 connection wiring to an IEEE 802.3af compliant network PoE
switch must not leave the building perimeter without adequate lightning
protection.
When the Intercom is connected to wiring that exits the building, there is
potential risk of lightning induced electrical surges or high voltages from
fault conditions. To reduce risk, outdoor wiring should be protected by Earth
grounded conduit whenever possible. Relay input and output connections
must not leave the building perimeter without adequate lightning protection.
Document 90-00075A
10/31/2019
Page 5
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Overview
Introduction
The 8039 SIP Video Intercom is ideal for secure business entrances, emergency
intercom, and gated entrances. The Algo 8039 provides hands-free intercom
capability with video, entrance security with door unlock control, rugged
weatherproof design, and superior audio performance.
Fully compatible with SIP industry standards, the 8039 SIP Video Intercom will
work with most hosted or enterprise SIP-base servers supporting third-party SIP
endpoints.
The 8039 SIP Video Intercom is configured using central provisioning features or
by accessing a web interface using browsers such as Google Chrome, Firefox, or
Internet Explorer.
What is Included
8039 SIP Video Intercom
Mounting Plate
What is not Included
Optional 8061 IP Relay Controller
Document 90-00075A
10/31/2019
Page 6
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Setup and Installation
Getting Started - Quick Install & Test
This guide provides important safety information which should be read thoroughly
before permanently installing the product.
1. Connect the 8039 SIP Video Intercom to an IEEE 802.3af compliant PoE network
switch. The backlight keypad will turn on. After about 30 seconds, a beep will signal the
completion of the boot process.
2. After the boot is complete, press the call button on the 8039 to hear the IP address.
(Once the SIP Server field is populated in the 8039 web interface, the call button will
contact the preconfigured extension when pressed.) The IP address may also be
discovered by downloading the Algo locator tool to find Algo devices on your network:
www.algosolutions.com/locator
3. Access the 8039 SIP Video Intercom web page by entering the IP address into a
browser (Chrome, IE, Firefox etc) and login using the default password algo .
4. Enter the IP address for the SIP server into the SIP Domain field under the BASIC
SETTINGS > SIP tab.
5. Enter the SIP Extension, Authentication ID, and Password. Also enter the target Dialing
Extension that the Intercom will call.
Note: The Authentication ID may also be called Username for some SIP servers, and in
some cases may be the same as the SIP extension.
6. Press the Call Button on the 8039 Intercom, then answer the phone to communicate
over the Intercom. Press the digit 6 on the phone keypad to activate the door control
relay for three seconds (if applicable).
Document 90-00075A
10/31/2019
Page 7
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Installation
The 8039 SIP Video Intercom is
weather protected for outdoor
installation. However, if network
cabling extends beyond the perimeter
of the building, then adequate lightning
protection is required to protect the
cabling and network switch from
lightning surges. No lightning
protection is required by UL or CSA if
the 8039 is located on the outside wall
of a building and the wiring is inside
the perimeter of the building.
The 8039 is wall and door frame
(mullion) mountable via the supplied
mounting plate:
Secure the mounting plate to the wall/
mullion door frame via two #8 screws.
Attach the 8039 into the mounting
plate and secure the device in place
with the attached security screw at the
bottom of the mounting plate using the
provided Allen wrench.
Programming and Configuration
The 8039 SIP Video Intercom is configurable using the web interface or
provisioning features.
After boot up, the speaker will beep and the intercom will have obtained an IP
address. If there is no DHCP server the 8039 SIP Video Intercom will default to the
static IP address 192.168.1.111.
Before the 8039 is configured, the call button on the front can be pressed to play
the IP address over the speaker. (Once the SIP Server field is populated on the
8039 web interface, the call button will contact the preconfigured extension when
pressed.) The IP address may be discovered by downloading the Algo locator tool
to find Algo devices on your network: www.algosolutions.com/locator
Document 90-00075A
10/31/2019
Page 8
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Enter the IP address (e.g 192.168.1.111) into a browser such as Google Chrome,
Firefox, or Internet Explorer (other than IE9). The web interface should be visible
and the default password will be algo in lower case letters.
Wiring Connections
Network Connection
The speaker provides a RJ45 jack for network
connection. A cable run from the switch can be
terminated to a modular jack with connection by patch
cord, or terminated with a RJ45 plug.
PoE (Power over Ethernet) must be 48V 350 mA IEEE
802.3af compliant whether provided by the network
switch or injector.
There are two lights on the Ethernet jack:
Green light: On when Ethernet is working, flickers off
to indicate activity on the port.
Amber light: Off when successful 100Mbps link is
established. Typically on only briefly at power up.
Under normal conditions, the Amber light will turn on
immediately after the Ethernet cable is first connected.
This indicates that PoE power has been successfully
applied. Once the device connects to the network, it
will switch to the Green light instead, which will
typically flicker indicating traffic on the network.
Door Control Relay
Provides both normally open and normally closed
relay contacts. Note: The 8061 IP Relay Controller
can be used as an alternative more secure option
for door opening control, by using a separate relay
from the public-facing intercom.
Serial Control
**Reserved for future use**
Door Sensor (Dry Contact Input)
An external call button can be connected as a normally open switch. When the
relay is triggered, this will dial the pre-configured “Extension to Dial”.
Document 90-00075A
10/31/2019
Page 9
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Backlit Keypad and Call Button
The backlit keypad and call button will be steady during power up and will flash
during a reset.
If enabled, when making a call, the call button light will flash rapidly, while the call
is ringing at the far-end phone. Once the call is answered, the flashing will slow
down.
Reset
The 8039 SIP Video Intercom can only be reset during a power up. To return all
the settings to the factory default for the 8039, wait until all the backlit keys start
flashing. Then press and hold the call button until the call button backlight
begins a double flash pattern. Release the call button and allow the unit to
complete its boot process. Do not press the call button until all the keys
start flashing.
A reset will set all configuration options to factory default including the password.
Document 90-00075A
10/31/2019
Page 10
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Web Interface Status and Login
Web Interface Login
The web interface requires a password which is ‘algo’ by default. This password
can be changed in the Admin tab after logging in the first time.
Web Interface is accessed by entering 8039’s IP Address into the web browse.
Important: It is highly recommended to change the default password if the device is
directly connected to a public network.
Document 90-00075A
10/31/2019
Page 11
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Status
The device’s Status page will be available before and after log on. The section can
be used to check 8039’s SIP Registration status of the SIP extensions, Call
Status, Proxy Status, Extension to Dial, Door Controller status, and general MAC,
IP, Netmask, and Date/Time information.
The Status page can be hidden when logged out for security purposes under the
Advanced Settings > Admin tab.
Status Tab – Video
The video can be seen in the “Status > Video” tab when the user is not logged in.
A separate video password can also be enabled, to allow users to access the
video, but not the rest of the device settings. This password can be set in “Basic
Settings > Video” tab, “Session Password” field. Video settings like brightness,
contrast, view (Dewarped or Fisheye) are also available in the “Basic Settings >
Video” tab.
Document 90-00075A
10/31/2019
Page 12
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Web Interface Basic Settings
Basic Settings Tab – SIP
SIP Server information and Credentials should be obtained from your telephone
system administrator or hosted account provider. After saving the settings, see the
Status tab to confirm the registration was successful.
Important: Any time changes are made to settings in the web interface the ‘Save’
button must be clicked to save the changes.
SIP Domain (Proxy Server)
The IP address (e.g. 192.168.1.111) or domain name (e.g. myserver.com) of the
SIP Server
SIP Extension
Used to register the 8039 on the SIP Server.
Authentication ID
May also be called Username for some SIP servers and in some cases may be
the same as the SIP extension.
Authentication Password
SIP password provided by the system administrator for the SIP account.
Extension to Dial
Enter the phone number that will be dialed when the call button is pressed. This
can also be a Hunt Group number. Ensure that voice mail is not reached.
Document 90-00075A
10/31/2019
Page 13
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Note: The “Basic Settings > Keypad” tab offers additional keypad modes like playing
a voice prompt when the call button is pressed and using the keypad to dial
extensions or listed departments.
Basic Settings Tab – Features
Speaker Volume
Select speaker audio level of the 8039 from 1 (lowest) to 10 (highest).
Automatic Gain Control (AGC)
Normalizes the audio level. This ensures audio level heard at the speaker is
always at a consistent level, independent of the phone that is used to answer the
call.
Answer Inbound Call
Allow the 8039 to auto-answer an inbound call. By default, this functionality is
activated.
Document 90-00075A
10/31/2019
Page 14
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Answer Tone
Select a tone to be played over the speaker when the intercom answers an
inbound call. Use only Default, or custom uploaded file. The other pre-installed
tone files all contain silence at the end in order to generate ring "cadence" of 6
seconds. This silence will block the voice path for several seconds at the start of a
call.
Outbound Ring Limit
This feature can be used to set a limit on how long the intercom will ring before
timing out. If the call is not answered within this time period, the 8039 will go back
to an idle state.
Ringback Tone
Select an audible ringback tone to be played on the 8039 speaker until the call is
answered.
Allow Call Button to End Active Call
If enabled, allows the visitor to end an active call by pressing the call button.
G.722 Support
Enable or disable the G.722 codec.
Maximum Call Duration
Select the maximum call length. The call will be terminated once the maximum
time is reached. In the event that a call inadvertently reaches voicemail or gets
accidentally left on hold, this setting ensures that the 8039 returns on-hook.
Door Sensor Connector
External call button can be used as an input to the door sensor connector.
External call button will function like the call button on the device.
Document 90-00075A
10/31/2019
Page 15
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Basic Settings Tab – Video
Exposure Region
Select an exposure calculation region for optimal image rendering. “Spot” method
calculates exposure based on the center area of the image. “Full Frame” method
uses the entire image to determine the exposure. “Centre Weighted” uses mainly
the center area and a fraction of the remaining frame to compute the exposure.
Camera View
Camera view can be set to either a “Dewarped” full page view or a circular
“Fisheye”.
White Balance
Select the white balance settings. “Auto” will auto-detect the light levels and auto-
balance the video accordingly. Other balance choices include: Daylight 6500K and
5500K, Fluorescent, and Incandescent.
Document 90-00075A
10/31/2019
Page 16
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Brightness
Increase or decrease image brightness either above or below the default value.
Contrast
Increase or decrease image contrast either above or below the default value.
Sharpness
Increase or decrease image sharpness either above or below the default value.
Saturation
Increase or decrease image saturation either above or below the default value.
Powerline Frequency
Choose the local powerline frequency. For example, 60 Hz in North America and
50 Hz in Europe. This allows the device to reduce video flicker when used with
indoor lighting.
Allow PTZ Video via DTMF Control
Use DTMF command to control the web video and H.264 video stream.
Packet Type
Refer to phone specifications to determine best supported packet type (“Single
NAL Unit” or “Fragmentation Unit Type A (FU-A)”). Use ‘Auto’ mode except with
legacy video phones with limited Video SDP negotiation capability.
CIF Stream Bitrate
Select the amount of network traffic the device can use.
HD Channel Resolution
Select the video resolution as supported by the video phone that will answer the
calls, 720p (1280x720) or VGA (640x480).
HD Channel Bitrate
Select the amount of network traffic the device can use.
Document 90-00075A
10/31/2019
Page 17
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Request Media Bandwidth
Adds bandwidth modifiers and attributes in the SDP offer/answer.
SIP Video Capacity
This controls the video parameters included in the SIP 'Offer' that is sent when the
8039 initiates a call. Select the video capacity as supported by the video phone
that will answer the calls.
SIP Video Stream
This controls the actual video stream sent by the 8039. Use ‘Auto’ mode unless a
manual override is required for compatibility with legacy video phones.
Maximum Browser Sessions
Allows for a limit to be set on the number of separate browser sessions that can be
open simultaneously to show the video. The setting can be “Disabled” to turn off
the web video capability.
Session Passcode
This allows a separate password to be configured that allows access to only the
“Status > Video” tab.
Document 90-00075A
10/31/2019
Page 18
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Basic Settings Tab – Keypad
Dial Mode – Single Number
This mode allows the 8039’s “Call” button to dial a pre-configured number, the
“Extension to Dial”. There is also an option to allow all the number keys on the
keypad to dial this same extension.
Dial Mode – List
This mode allows each of the 10 “number” keys to dial a different preconfigured
phone number. For example, 1 for Reception, 2 for Sales, 3 for Shipping, etc.
The Call button can be configured to play a voice prompt detailing the available
options to the visitor. The voice prompt can be uploaded via a custom audio file in
the “Advanced Settings > File Manager” tab.
Dial Mode – Keypad Dial
This mode allows the keypad to be used to dial extensions directly. If an incorrect
number is dialed by mistake, the “#” key can be pressed to cancel, and the
extension can be dialed again.
Set the “Length of Extension to Dial”, correctly to match the extension length of
your phone system.
The Call button can be set to “Dial Extension” (e.g. reception) or to “Play Voice
Prompt” giving the visitor instructions and/or summary of main extensions to dial
via the keypad.
Document 90-00075A
10/31/2019
Page 19
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8039 SIP Video Intercom (FW version 2.0.1)
Warning: Set appropriate permissions on the phone system to ensure that a
malicious visitor cannot use the intercom to dial an external number. Also ensure
that a visitor will not reach voicemail to prevent the call from getting “stuck”
Keypad Backlight
Enable or disable the Keypad’s blue backlight.
Call Button Backlight
Enable or disable the Call Button’s blue backlight.
Backlight Brightness
Configures the brightness of the Keypad and Call Button backlight if they are
enabled.
Basic Settings Tab – Door Control
The 8039 contains a relay that can be used for Door Control, or it can be used with
the optional 8061 IP Relay Controller (sold separately) for additional door security,
as the 8061 can be located inside the building and separate from the public-facing
intercom. This section allows you to configure the 8061 settings (if used), or the
local door relay. For more information about the 8061, see “8061 IP Relay
Controller” on page 48.
Number of Network Door Controllers
Set up to 4 network door controllers (8061s) to unlock/lock the doors.
Document 90-00075A
10/31/2019
Page 20
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51

Algo 8039 User guide

Category
Door intercom systems
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI