Generation Lighting 5231 Installation guide

5231
Brand
Generation Lighting
Model
5231
Type
Installation guide
Install canopy loop (E) on canopy (G) with lockwasher (Q) and nut (B).
(Note: Loop may be factory installed.).
STEP 1:
To replace glass, bend upper and lower tabs in corners of glass to be
replaced. Install glass up through bottom of fixture. Bend tabs back
as before.
REPLACING GLASS
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-264
0
81409
• Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
• If you are unclear as to how to proceed, contact a qualified
electrician.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
• Read instructions carefully.
•
Save these instructions.
IMPORTANT SAFETY INSTRUCTIONS
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
CLEANING
ORDERING PARTS
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the scr
ews or parts which are needed to install this fixtur
e.
BEFORE YOU BEGIN
FOR CHAIN HUNG (FIG. 1)
Install lock washer (Q), nipple (C) and fixture loop (J), in that or
der
, on
coupling (M).
STEP 2:
*
OUTLET BOX
*WIRE
*CONNECTORS
CANOPY (G)
CANOPY
LOOP (E)
MOUNTING
SCREWS (I)
CHAIN (N)
NUT (B)
FIXTURE
LOOP (J)
CENTER
PIPE (P)
FIGURE 1 *NOT SUPPLIED
FOR CHAIN HUNG
GROUNDING
AND
MOUNTING
BAR
LOCK UP
GREEN GROUNDING SCREW (D)
*OUTLET
*BOX
SCREWS
MOUNTING
BAR (A)
*WIRE
CONNECTORS
MOUNTING
SCREWS (I)
*GROUND
*WIRE
*OUTLET
*BOX
FIGURE 2
*NO
T INCLUDED
FIXTURE
CAGE (O)
CAP NUTS (F)
COUPLING (M)
CANDLE
COVER (T)
Insert fixtur
e assembly thr
ough canopy (G). Secur
e in place with lock
washer (Q) and nut (B).
STEP 2: FOR FLUSH MOUNT (IF APPLICABLE) (FIG. 3)
Install nipple (C) onto coupling (M) (if applicable).
STEP 3:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (G) against ceiling allowing for mounting
screws (I) to protrude through holes in canopy (G). Secure in place
with cap nuts (F).
Make sure no bare wires can be seen outside wire connectors.
Install lamps.
Install candle covers (T) (if applicable).
INSTALLATION HC-264
FINAL ASSEMBLY
STEP 4:
STEP 5:
STEP 6:
TOP OF
FIXTURE (K)
NUT (B)
LOCKWASHER (Q)
CANOPY (G)
CAP NUTS (F)
FIGURE 3
COUPLING (M)
FOR FLUSH MOUNT
I
MPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
T
hread fixture mounting screws (I) in through top of mounting bar (A)
(raised side is on top, as illustrated). Run screw threads all the way
down to the heads. Secure mounting bar (A) to outlet box with outlet
box screws (not supplied). For flush mount proceed to step 4.
STEP 1:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 2:
GROUNDING INSTRUCTIONS
:
Connect the supply ground wire, fixture ground wire, and mounting bar
ground wire (pre attached) using the supplied wiring connector. Gently try
to remove the wires from the connector. If you can remove the wires,
carefully re-do the wiring connection.
STEP 3:
  • Page 1 1
  • Page 2 2

Generation Lighting 5231 Installation guide

5231
Brand
Generation Lighting
Model
5231
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents