Zonet ZFN2601 Installation guide

Zonet
Brand
Zonet
Model
ZFN2601
Category
Interface cards/adapters
Type
Installation guide
P
P
C
C
S
S
y
y
s
s
t
t
e
e
m
m
R
R
e
e
q
q
u
u
i
i
r
r
e
e
m
m
e
e
n
n
t
t
s
s
1. A Pentium based PC, minimum required speed 400Mbps (recommended)
2. One available PCI slot
3. Windows 2000/XP/Vista
P
P
a
a
c
c
k
k
a
a
g
g
e
e
c
c
o
o
n
n
t
t
e
e
n
n
t
t
˙ One ZFN 2601
˙ One Quick Installation Guide
˙ One 1394 Cable
H
H
a
a
r
r
d
d
w
w
a
a
r
r
e
e
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
To install the 1394 PCI card, please follow below procedures:
1. Turn-OFF the computer and unplug the power cord from the back of the computer
2. Open the cover to gain access to the motherboard of the computer
3. Insert the 1394 PCI card to an available PCI slot
4. Press the 1394 PCI card gently
5. Make sure all gold-fingers are fully seated and contacted into the PCI slot
6. Secure the 1394 PCI card PCI bracket with a screw to the chassis
7. Close the cover of the chassis
8. Plug in the power cord and turn-ON the computer
9. Follow the Software Installation procedures on the next step
S
S
o
o
f
f
t
t
w
w
a
a
r
r
e
e
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
After turn-ON the computer, the hardware will be detected automatically. The operating
system will install all necessary driver files for the hardware. After approximately 1 minute, a
message will appear at the lower right-hand corner “Your new hardware is now installed
and can be used.” The hardware and software installation is completed.
T
T
r
r
o
o
u
u
b
b
l
l
e
e
s
s
h
h
o
o
o
o
t
t
i
i
n
n
g
g
1. Q: Why I don’t see the New Hardware Found wizard after I installed the hardware and
turn-ON my computer?
A: Re-seat the 1394 PCI card to the (same or other available) PCI slot. Make sure all its
gold-fingers are firmly contacted into the PCI slot and the PCI slot works for other PCI
adapters.
2. Q: Why my computer does not install the 1394 PCI card?
A: Only Windows operating system has fully supported for IEEE1394 host controllers.
You may need to upgrade your system.
3. Q: Why my FireWire (IEEE1394) device(s) are not working with the 1394 PCI card?
A: Re-connect the device FireWire cable and make sure the cable is working properly.
Refer to the FireWire device instruction manual and make sure the device driver is
installed correctly. Additional software may need to install for the device, such as
DirectX 8.1 or later version.
Note: 1394 PCI card only supports FireWire device(s) that consume no more than 1.5A
voltage.
12-086-00701 Rev:01
  • Page 1 1
  • Page 2 2

Zonet ZFN2601 Installation guide

Zonet
Brand
Zonet
Model
ZFN2601
Category
Interface cards/adapters
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents