Metra Dash kit Installation guide

Category
Car kits
Type
Installation guide

Metra Dash kit

The Metra Dash kit is a car audio installation kit that allows you to replace your factory radio with an aftermarket radio. It is designed to fit the Kia Optima 2011-up and includes an ISO DIN head unit provision with pocket, painted matte black to match the factory finish. The kit also includes all the necessary hardware for installation, including brackets, trim panel, pocket, and screws.

The Metra Dash kit is easy to install and can be completed in a matter of minutes. It is a great way to upgrade your car's audio system and get the most out of your aftermarket radio.

Metra Dash kit

The Metra Dash kit is a car audio installation kit that allows you to replace your factory radio with an aftermarket radio. It is designed to fit the Kia Optima 2011-up and includes an ISO DIN head unit provision with pocket, painted matte black to match the factory finish. The kit also includes all the necessary hardware for installation, including brackets, trim panel, pocket, and screws.

The Metra Dash kit is easy to install and can be completed in a matter of minutes. It is a great way to upgrade your car's audio system and get the most out of your aftermarket radio.

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
APPLICATIONS
1-800-221-0932
metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-7345B
WIRING & ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-7304 - Hyundai/Kia 2010-up
Antenna Adapter:
• Not Required
Panel Removal Tool • Phillips Screwdriver • Socket Wrench
TOOLS REQUIRED
Kia Optima 2011-up
99-7345B
B C D
E
A
A) Brackets B) Trim Panel • C) Pocket D) (3) #8 x 3/8” Pan Head Phillips Screws
• E) (4) #8 x 3/8” Truss Head Phillips Screws
KIT FEATURES
KIT COMPONENTS
• ISO DIN head unit provision with pocket
Painted matte black to match factory finish
Table of Contents
Dash Disassembly
– Kia Optima 2011-up 3-4
Kit Assembly
– Vent transfer 5
– ISO DIN head unit provision with pocket 6
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
99-7345B
Caution
Metra recommends disconnecting the negative battery terminal before beginning any
installation. All accessories, switches, and especially air bag indicator lights must be
plugged in before reconnecting the battery or cycling the ignition.
*NOTE: Refer also to the instructions included with the aftermarket radio.
1. Unsnap and remove trim from around
top center to passenger side dash.
(Figure A)
2. Unsnap panel from outside edge of
driver’s side dash. (Figure B)
3. Remove two screws from knee panel
and pull top of panel back so it doesn’t
overlap the instrument cluster.
(Figure C)
4. Remove two screws from the driver’s
side vent trim and remove. (Figure D)
Continued on next page
3
Dash Disassembly
99-7345B
(Figure B)
(Figure A)
(Figure C)
(Figure D)
4
99-7345B
Dash Disassembly
5. Remove five screws from instrument
cluster and remove. (Figure E)
6. Remove four screws from the climate
controls and remove. (Figure F)
7. Remove six screws securing the radio
trim panel and remove. (Figure G)
8. Remove four screws securing the
factory radio chassis and remove it.
(Figure H)
Continue to kit assembly
(Figure F)
(Figure E)
(Figure G)
(Figure H)
5
99-7345B
1. Remove three screws and remove
the vent from the factory radio panel.
(Figure A)
2. Using the supplied #8 x 3/8” pan head
phillips screws, install the vent to the
kits trim panel. (Figure B)
Continued on next page
Kit Assembly
(Figure A)
(Figure B)
Kit Assembly 99-7345B
6
ISO DIN head unit provision with pocket
(Figure A)
(Figure B)
(Figure C)
1. Mount the pocket to the brackets with
the supplied (4) screws. (Figure A)
2. Mount the radio to the brackets with the
screws supplied with the unit.
(Figure A)
3. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
4. Mount the radio/bracket assembly into
the dash. (Figure B)
5. Snap the radio trim plate over the radio/
bracket assembly and reassemble dash
in reverse order of disassembly
(Figure C).
Notes
METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932
metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-7345B
REV. 9/07/11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Metra Dash kit Installation guide

Category
Car kits
Type
Installation guide

Metra Dash kit

The Metra Dash kit is a car audio installation kit that allows you to replace your factory radio with an aftermarket radio. It is designed to fit the Kia Optima 2011-up and includes an ISO DIN head unit provision with pocket, painted matte black to match the factory finish. The kit also includes all the necessary hardware for installation, including brackets, trim panel, pocket, and screws.

The Metra Dash kit is easy to install and can be completed in a matter of minutes. It is a great way to upgrade your car's audio system and get the most out of your aftermarket radio.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI