Airwell PNV 007 Installation guide

INSTALLATION MANUAL

MODELS

Wall-mounted type

PNV 007 PNV 015

PNV 009 PNV 018

PNV 012 PNV 021

SAFETY PRECAUTIONS

Part NO:468050156/02

● Readthefollowing"SAFETYPRECAUTIONS"carefullybeforeinstallation.

● Carryouttestrunningtoconrmthatnoabnormalityoccursaftertheinstallation.Then,explaintousertheoperation,careandmaintenanceas

statedininstructions.Pleaseremindthecustomertokeeptheoperatinginstructionsforfuturereference.

Thisindicationshowsthepossibilityofcausingdeathorseriousinjury.

WARNING

Thisindicationshowsthepossibilityofcausingharmordamagetheequipment.

CAUTION

WARNING

1)Usequaliedinstallerandfollowcarefullythisinstructions.Otherwiseitwillcauseelectricalshock,waterleakage,orestheticproblem.

2)Installatastrongandrmlocationwhichisabletowithstandtheset'sweight.Ifthestrengthisnotenoughorinstallationisnotproperlydone,theset

willdropandcauseinjury.

3)Forelectricalwork,followthelocalnationalwiringstandard,regulationandthisinstallationinstruction.Anindependentcircuitandsingleoutletmust

beused.Ifelectricalcircuitcapacityisnotenoughordefectfoundinelectricalwork,itwillcauseelectricalshockorre.

4)Usethespeciedcableandconnecttightlyforindoorconnection.Connecttightlyandclampthecablesothatnoexternalforcewillbeactedonthe

terminal.Ifconnectionorxingisnotperfect,itwillcauseheat-uporreattheconnection.

5)Wireroutingmustbeproperlyarrangedsothatcontrolboardcoverisxedproperly.Ifcontrolboardcoverisnotxedperfectly,itwillcauseheat-up

atconnectionpointofterminal,reorelectricalshock.

6)Whencarryingoutpipingconnection,takecarenottoletairsubstancesotherthanthespeciedrefrigerantgointorefrigerationcycle.Otherwise,it

willcauselowercapacity,abnormalhighpressureintherefrigerationcycle,explosionandinjury.

7)Donotdamageoruseunspeciedpowersupplycord.Otherwise,itwillcausereorelectricalshock.

8)Thisequipmentmustbeearthed.Itmaycauseelectricalshockifthegroundingisnotperfect.

9)Donotinstalltheunitatplacewhereleakageofammablegasmayoccur.Incasegasleaksandaccumulatesatsurroundingoftheunit,itmay

causere.

CAUTION

1)Selectionoftheinstallationlocation.

Selectainstallationlocationwhichisrigidandstrongenoughtosupportorholdtheunit,andselectalocationforeasymaintenance.

2)Donotreleaserefrigerant.

Donotreleaserefrigerantduringpipingworkforinstallation,reinstallationandduringrepairingarefrigerationparts.Takecareoftheliquidrefrigerant.

itmaycausefrostbite.

3)Itmayneedtwopeopletocarryouttheinstallationwork.

4)Donotinstallthisapplianceinalaundryroomorotherlocationwherewatermaydripfromtheceiling,etc.

5)Carryoutdrainagepipesasmentionedininstallationinstructions.Ifdrainageisnotperfect,watermayentertheroomanddamagethefurniture.

IM_PNV_1 A 1_GB

Required tools for Installation

NO. TOOI NO. TOOI.

1 Screwdriver 7 Knife

Electricdrill,hole

coredrill(60mm)

8 Measuringtape

3 Hexagonalwrench

9 Torquewrench

4 Spanner

5 Pipecutter

6 Reamer

Attached accessories

No. Accessories part Qty.

Mountingplate

Airpurifyinglter(optional)

Swrewswasherdowels

Unitoperationmanual

Installationmanual

SELECT THE BEST LOCATION

HOW TO FIX INSTALLATION PLATE

 Thereshouldnotbeanyheatsourceorsteamneartheunit.

 Thereshouldnotbeanyobstaclesblockingtheaircirculation.

 Aplacewhereaircirculationintheroomisgood.

 Aplacewheredrainagecanbeeasilydone.

 Donotinstalltheunitnearthedoorway.

 Ensurethespacesindicatedbyarrowsfromthewall,ceiling,fenceorotherobstacles.(Fig1)

 Theapplianceshallbeinstalledover2.3mhigh.

Themountingwallisstrongandsolidenoughtopreventitfromthevibration.

Theedgeofinstallationcartonboardshouldbeatmorethan50mmatrightandleftofthewall.

 1.Locatethemountingplateonthewallinahorizontalposition.

 2.Markthepositionofthefourmountingholesonthewallanddrillfourholestoaccommodatethedowels.

 3.Mountthemountingplateonthewallbythefourscrews.Ensurescrewsaretightenedproperly.

 4.Markthelocationofthepipingholeoneithersideofthemountingplateasshown.

 5.Thepipingholeisdrilledata5down-wardangletopreventcondensedorrainwalerfrompenetratingbackintotheroom.

 6.Trimtheholeinthewallwitha70mmcommercialplastictube.

PNV 007

PNV 009

PNV 012

Fig1-1

50mm

min

50mm

min

PNV 015

PNV 018

PNV 021

UNIT INSTALLATION

Unitoffersvedirectionsforinstallingrefrigerantpipe,pleaseinstallingtheunitaccordingtofollowinginstalltion:

1.Knockoutholeandpulloutthepipes. 4.Purifyinglterinstallation(optional).

2.Installtheunittowall. 5.Checkthedrainage.

3.Securetheunit.

Pull out the piping and hose

Install the Indoor Unit

 1.Hook the indoor unit onto the upper portion of

installationplate(Engagetheindoorunitwiththe

upper edge of the installation plate).ensure the

hooksareproperlyseatedontheinstallationplate

bymovinginleftandright.

 2.Usedtheinstallationsupport thatassembletothe

unithousingtosupport the indoorunitinaangle

about25",thanconnectedthepiping and power

supplycord.

Movethedrainhosenear

toarrowmarkandtapeit

withpipinginapositionas

mentionedinFig.below

Coverforthe

rightpiping

Coverforthe

bottompiping

Coverforthe

leftpiping

Drainhose

Piping

Piping direction

Right

Rightrear

RightBottom

LeftRear

Left

(Frontside)

Hooksat

installationplate

Piping

Drainhose

Fig1-2

Install the Indoor Unit(Continue)

Totakeouttheunit,pullthe

markingatthebottomunit,andpullit

slightlytowardsyoutodisengagethe

hooksfromtheunit.

Purifying lter installation (optional)

1.Openthegrille.

2.Removetheairfilters.

3.Putairpurifyingfilterintoplaceasshowninillustration.

Secure the Indoor Unit

1.Tapetheextraconnectingcableinabundleandkeepitbehindthe

chassis.Ensurethattheconnectingcableisnotclampedinbetween

theunit'shook(2positions)andinstallationplate.

2.Pressthelowerleftandrightsideoftheunitagainsttheinstallation

plateuntilhooksengageswiththeirslots(soundclick).

marking

Attentionnottobend

updrainhose

Rearview

Unit's

hook

Installation

plate

Insulationofpipingconnections

●Carryoutinsulationafterchecking

forgasleaksandsecurewithvinyl

tape.

Vinyltape

Collaboratethepiping

communication

wiring

Drainhose

Adjustthepipingslightlydownwards.

Airpurifyinglter

Airlter

1Bendthepipeas

closelyonthewallas

possible,butbecareful

thatitdoesn’tbreak.

2Donotwiringthe

powerwireand

communicationwire

together.

How to take out front grille

Pleasefollowthestepsbelowtotakeoutfrontgrilleifnecessaryduringservicing.

1.Settheverticalairflowdirectionlouvertothehorizontalposition.

2.SlidedownthetwocapsofPNV007/009/012onthefrontgrilleasshownin

theillustrationatright,thenremovethetwomountingscrews.(Iftheunitis

PNV015/018/021,ithasthreecaps).

3.Pullthelowersectionofthefrontgrilletowardsyourtoremovethefrontgrille.

Check the drainage

1Openfrontpanelandremoveairfilters.

(Drainagecheckingcanbecarriedoutwithoutremovingthefrontgrill).

2Pouraglassofwaterintothedraintray-styrofoam.

3Ensurethatwaterflowsoutfromdrainhoseoftheindoorunit.

Height Compensation Setting

TheCompensationsettingaccordingtoinstallationheightcanbedonebyusingthedipswitch11and12oncontrollerPCB.

InstallationHeight HeightCode DS11 DS12

2.3-2.7(m) H0 OFF OFF

2.7-3.1(m) H1 OFF ON

3.1-3.5(m) H2 ON OFF

>3.5(m) H3 ON ON

Note

1.Pleasedisconnecttheunitfrompowersupplywhenchangethesesettings.

2.Ifyoufeeltoonoisy,pleasesetDS11andDS12tolowerheightcodelevel.

Verticalairow

deectionlouver

(Movethevertical

vanetohorizontal)

Draintraystyrofoam

ELECTRICAL WRING CONNECTION

Terminalblock(4P)

Powersupply

Terminalblock(2P)

Powersupplywiring

Tiethecommunicationwiringwithclamptightening

Fixthepowersupplywiringunderthecliptightening

Connect the drainage pipe

1UsestandardhardPVCpipe(19mm)forthedrainpipe.

2Usethedrainhosetochangethedirection.

3Insertthedrainhoseuntilitconnectsthedrainportverywell,andthensecureittightlywiththehoseclamp.

4Aftercheckingthedrainage,wrapthedrainhosewiththeinsulationandclamps.

Powersupplywiring

Tighteningtotorquefortheterminalscrews

Electricalcharacteristic

SpecicationsforeldsuppliedELBandwire

MainbusandR/Ccommunciationwiring

1.Unscrewandremovetheservicelid.

2.Connect the power supply wiring to the power supply

terminalblock.

3.Whendoingthis,pressthe powersupplywiring underthe

wirecliptightly.

1.Usethecorrectscrewdriverfortighteningtheterminalscrews.Ifthebladeofscrewdriveristoosmall,theheadofthescrewmightbedamaged,andthe

screwwillnotbeproperlytightened.

2.Iftheterminalscrewsaretightenedtoohard,screwsmightbedamage.

3.Refertothetablebelowforthetighteningtorqueoftheterminalscrews.

1.Unscrewandremovetheservicelid.

2.ConnecttheR/CwiringstoR1,R2terminalblockandthe

mainbuswiringstoF1,F2terminalblock.

3.Pressthewiringsunderthewirecliptightly.

Terminal Size Tighteningtorque

Remotecontroller,Transmissionwiringandforcedoffterminalblock(4P) M3.5 0.8~1.0N.m

PowersupplyandGroundterminalblock(3P) M4 1.2~1.5N.m

Unit Powersupply Fanmotor

Model Hz Volts MCA MFA KW FLA

LEV22

50 220~240

0.23 16 0.02 0.06

LEV28 0.23 16 0.02 0.06

LEV36 0.23 16 0.02 0.06

LEV45 0.23 16 0.02 0.07

LEV56 0.23 16 0.02 0.07

LEV63 0.23 16 0.02 0.07

MCA:Min.CircuitAmps(A)

MFA :Max.FuseAmps(A)

KW :FanMotorRatedoutput(KW)

FLA :FullLoadAmps(A)

Model Powersupplywiring

Remotecontrollerwiring

communicationwiring

PNV007 FieldELB WireandSize Wire Size

PNV009

16A

Mustcomply

withmaximum

currentandlocal

codes(≥0.75mm

)

Twisted-

pairwires

≥1.0mm

PNV012

PNV015

PNV018

PNV021

All fieldsupplied parts andmaterials and electrics worksmust



conformtolocalcodes.

Usecopperwireonly.



Allwiringmustbeperformedbyanauthorizedelectrician.



Everyindoorunitmusthavea subcircle breakerandthewhole



systemmusthaveamaincirclebreaker.

Besuretogroundtheairconditioner.



The appliance shall be installed in accordance with national



wiring regulations, and shall be provided to ensure all-pole

disconnectionfromthesupplymains,anddistancebetweenthe

polesshallbemorethan3mm.

CHECK ITEMS

BEFORE POWER ON

�

 Isthereanygasleakageatarenutconnections?

�

 Hastheheatinsulationbeencarriedoutatarenutconnection?

�

 Istheconnectingcablebeingxedtoterminalboardrmly?Isthe

connectingcablebeingclampedrmly?

�

 Isthedrainageok?

�

 (Referto"Checkthedrainage"section)

�

 Istheearthwireconnectionproperlydone?

�

 Istheindoorunitproperlyhookedtotheinstallationplate?

�

 Isthepowersupplyvoltagecompliedwithratedvalue?

AFTER POWER ON

�

 Isthereanyabnormalsound?

�

 Isthecoolingoperationnormal?

�

 Isthethermostatoperationnormal?

�

 Istheremotecontrol'sLCDoperationnormal?

NOTE:Forthepipingandwiringmethods,leakagetest,vacuumprocessandinstallationsetting

throughHMI,pleaserefterto“OutdoorunitInstallationManual”.

NOTE:Forhowtoconnectthepowerwireandcommunicationwirebetweenoutdoorunitandindoorunits,pleasereferto

chapter9“FieldWiring”inoutdoorunitinstallationmanual.

Airwell PNV 007 Installation guide

Related papers

Other documents