URCERI Rotary Tools Kit Flex Shaft 100 Accessories 6 Adjustable Speed 120V/60HZ Frequency, 135W Power and 35000 rpm No-Load Speed, Multiple-Function for Craft Projects User manual

Rotary Tool Kit

User Manual

Page is loading ...

EN-1

Thank you for choosing URCERI. Please read the instructions and warnings

thoroughly before use.

Safety Warning

1) WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.

• Do not operate tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Tools create sparks which may ignite the

dust or fumes.

• Keep children and bystanders away while operating a tool. Distractions

can cause you to lose control.

2) ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with grounded tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

• Avoid body contact with grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your

body is grounded.

• Do not expose power tools to rain or wet conditions. Water entering a tool

will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the tool. Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase the risk of electric

shock.

• When operating a tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a tool in a damp location is unavoidable, use a residual

current device (RCD) protected supply. Use of an RCD reduces the risk of

electric shock.

3) PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication. A moment of

inattention while operating tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate conditions will reduce personal

injuries.

• Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up or

carrying the tool.

• Carrying tools with your finger on the switch or energising tools that have

the switch on invites accidents.

• Remove any adjusting key or wrench before turning the tool on. A wrench

or a key left attached to a rotating part of the tool may result in personal

injury.

• Do not overreach. Keep proper footing and balance at all times. This

enables better control of the tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust

collection can reduce dust- related hazards.

4) TOOL USE AND CARE

• Do not force the tool. Use the correct tool for your application. The correct

tool will do the job better and safer at the rate for which it was designed.

• Do not use the tool if the switch does not turn it on and off. Any tool that

cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/or the battery pack from

the tool before making any adjustments, changing accessories, or storing

tools.Such preventive safety measures reduce the risk of starting the tool

accidentally.

EN-2

• Store idle tools out of the reach of children and do not allow persons

unfamiliar with the tool or these instructions to operate the tool. Power

tools are dangerous in the hands of untrained users.

• Maintain tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the tool's

operation. If damaged, have the tool repaired before use. Many accidents

are caused by poorly maintained tools.

5) SERVICE

Have your tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the tool is maintained.

6) SAFETY INSTRUCTIONS RELATED SPECIFICALLY TO THE

EQUIPMENT

1. Please turn off the product immediately after use.

2. When you are using accessories that are not included in the package, you

need to compare the maximum acceptable RPM of the accessory with the

RPM of the tool.

3. Switch off the tool immediately if electrical or mechanical malfunctions

occur.

4. Make sure that you will not accidentally start the tool when installing

accessories.

5. Never use grinding wheels over 1” (25.4mm) in diameter.

6. Never use the shaft lock button when the product is turned on.

7. Never use drill bits over 1/8” (3.2mm) in diameter.

8. Ensure that the size of the accessory fits the size of collet.

9. Charge the tool only with the supplied charger.

10. Do not disassemble the product.

11. This product is not waterproof. Do not expose it to rain or water.

12. This product is for indoor use only. Never charge the unit outdoor.

13. Do not charge the product continuously for more than 10 hours.

EN-3

Product Overview

1 2 3 4 5

6 7

98

10

1. Collet Nut

2. Housing Cap

3. Shaft Lock Button

4. Carbon Brush Cap

5. Speed Dial

6. ON/OFF Switch

7. Hanger

8. Flex Shaft

9. Collet Nut

10. Inner Core

EN-4

Accessories

Polishing Wheel Drum Sander Grinding Stone

Drill Bit Mandrel (connect the

mandrel to the

polishing wheel)

Cut-off Wheel

Collet Sanding Disc Wrench

Diamond burrs

(for grinding and

polishing)

Whetstone (for

sharpening)

Wire Brush (for

grinding and

polishing)

L wrench

EN-5

Install the flex shaft and accessory

1. Remove the housing cap by turning it counter-clockwise.

2. Hold the shaft lock button and at the same time turn the collet nut

counter-clockwise to loosen it.

3. Insert the inner core of the flex shaft into the collet.

4. Once the inner core is fully inserted, hold the shaft lock button and at the

same time turn the collet nut clockwise to tighten it. Use the wrench to

make sure the flex shaft does not comes loose during operation.

5. Once the collet nut is securely tightened, slide down the silver housing of

the flex shaft and screw it onto the rotary tool.

6. Fully insert the L wrench into the hole on the other end of the flex shaft.

Rotate the collet nut in the direction of the arrow to loosen it.

7. A collet is placed under the chuck nut. Replace the collet if necessary.

Choose the collet with the correct size for the accessory you want to use.

8. Insert the appropriate accessory into the collet.

9. Once the accessory is fully inserted, press down the L wrench and at the

same time tightens the chuck nut by turning it clockwise. Use the wrench

to make sure the accessory does not come loose during operation.

Operating at High Speed

Use high speed on hard objects such as hardwoods, metals and glass and

for carving, cutting as well as drilling.

Operating at Low Speed

Do not operate at high speed on certain materials because the friction may

generate heat and causes the plastic to melt.

Use low speed on delicate objects and for polishing and grinding.

Note: When using the grinding wheels, set the speed at ‘1’. Do not use it for

high speed operation.

Note: The received voltage will affect the speed of the tool. Speed would

drop as a result of decreased voltage. If your tool appears to be running

slowly, simply increase the speed setting.

Maintenance

Check carbon brushes every 2 to 6 months. Make sure that the power cord

is unplugged before checking the carbon brushes.

Do not allow break fluids, gasoline, petroleum-based products, penetrating

oils, etc. to come into contact with the housing of the product. They contain

chemicals that can damage, weaken or destroy the housing.

Inspect all mounting screws regularly and ensure they are securely

tightened.

Failure to do so could result in serious injuries.

Clear the debris inside the tool regularly.

Specifications

Voltage/Frequency: US: 120V~60Hz, EU: 230V-240V~50Hz, JP: 100V~60Hz

Power: US/EU: 135W, JP: 90W

n: US&EU: 35,000 min

-1

(Max), JP: 28,000 min

-1

(Max)

Collet Size: 3.2mm

Package Contents

1 x Rotary Tool

1 x Storage Case

1 x Flex Shaft

1 x Accessory Kit

1 x User Manual

1 x Warranty Card

Warranty

Our company provides customers with a warranty of 12 months from the

date of purchase. Please note that accessories are not covered by this

warranty.

Contact us

For any inquiries or comments concerning our products, please send an

email to [email protected], and we will respond to you as soon as

possible.

EN-6

Install the flex shaft and accessory

1. Remove the housing cap by turning it counter-clockwise.

2. Hold the shaft lock button and at the same time turn the collet nut

counter-clockwise to loosen it.

3. Insert the inner core of the flex shaft into the collet.

4. Once the inner core is fully inserted, hold the shaft lock button and at the

same time turn the collet nut clockwise to tighten it. Use the wrench to

make sure the flex shaft does not comes loose during operation.

5. Once the collet nut is securely tightened, slide down the silver housing of

the flex shaft and screw it onto the rotary tool.

6. Fully insert the L wrench into the hole on the other end of the flex shaft.

Rotate the collet nut in the direction of the arrow to loosen it.

7. A collet is placed under the chuck nut. Replace the collet if necessary.

Choose the collet with the correct size for the accessory you want to use.

8. Insert the appropriate accessory into the collet.

9. Once the accessory is fully inserted, press down the L wrench and at the

same time tightens the chuck nut by turning it clockwise. Use the wrench

to make sure the accessory does not come loose during operation.

Operating at High Speed

Use high speed on hard objects such as hardwoods, metals and glass and

for carving, cutting as well as drilling.

Operating at Low Speed

Do not operate at high speed on certain materials because the friction may

generate heat and causes the plastic to melt.

Use low speed on delicate objects and for polishing and grinding.

Note: When using the grinding wheels, set the speed at ‘1’. Do not use it for

high speed operation.

Note: The received voltage will affect the speed of the tool. Speed would

drop as a result of decreased voltage. If your tool appears to be running

slowly, simply increase the speed setting.

Maintenance

Check carbon brushes every 2 to 6 months. Make sure that the power cord

is unplugged before checking the carbon brushes.

Do not allow break fluids, gasoline, petroleum-based products, penetrating

oils, etc. to come into contact with the housing of the product. They contain

chemicals that can damage, weaken or destroy the housing.

Inspect all mounting screws regularly and ensure they are securely

tightened.

Failure to do so could result in serious injuries.

Clear the debris inside the tool regularly.

Specifications

Voltage/Frequency: US: 120V~60Hz, EU: 230V-240V~50Hz, JP: 100V~60Hz

Power: US/EU: 135W, JP: 90W

n: US&EU: 35,000 min

-1

(Max), JP: 28,000 min

-1

(Max)

Collet Size: 3.2mm

Package Contents

1 x Rotary Tool

1 x Storage Case

1 x Flex Shaft

1 x Accessory Kit

1 x User Manual

1 x Warranty Card

Warranty

Our company provides customers with a warranty of 12 months from the

date of purchase. Please note that accessories are not covered by this

warranty.

Contact us

For any inquiries or comments concerning our products, please send an

email to [email protected], and we will respond to you as soon as

possible.

EN-7

Page is loading ...

MADE IN CHINA

Web: www.urceri.com

E-mail: support@urceri.com

Page is loading ...

URCERI Rotary Tools Kit Flex Shaft 100 Accessories 6 Adjustable Speed 120V/60HZ Frequency, 135W Power and 35000 rpm No-Load Speed, Multiple-Function for Craft Projects User manual

URCERI Rotary Tools Kit Flex Shaft 100 Accessories 6 Adjustable Speed 120V/60HZ Frequency, 135W Power and 35000 rpm No-Load Speed, Multiple-Function for Craft Projects User manual

in other languages

Other documents