Bluetooth Skull
User Manual
Thank you very much for purchasing our Bluetooth Skull
Speaker. Please read this manual before using,
understanding this product will make it much easier to
use.
Product specifications
Model: Skull w Sunglasses
Type: Skull Bluetooth stereo
Connection mode: bluetooth connectivity, 3.5 MM audio
jack, TF, USB
Signal to noise ratio: 75 db or higher
Power supply: built-in lithium battery
Frequency: 60 hz to 15 KHZ
Battery capacity:1200 am
Play time: 5-10 hours
Speaker specifications: 5.7 cm, 8 w
Distortion rate: 1% or less
Product size: 10 * 10 * 13 cm
Net weight: 0.6 kg
Packing includes: 1-speaker, 1-3.5 auxiliary cord, 1-USB
power cord, this manual
After pressing the power button, you will hear the evil
laugh start up and tooth lights flashing at the same time.
After startup, bluetooth searches automatically, the
bluetooth indicator light will flash. Now pair the device to
your phone, name should appear as “Skull” but may differ
depending on device. After successfully pairing to the
speaker, bluetooth indicator light will flash, sound will
prompt. This machine has a memory function, after the
bluetooth connection has been set up the bluetooth will
connect automatically when the speaker is powered on. If
bluetooth connection fails, please shutdown and restart,
also may be because the battery power is insufficient,
please recharge.
Tooth Buttons
The front teeth of this model are buttons, they can be
used for either skipping songs or adjusting volume.
Changing song: To change songs simply tap the buttons,
+ goes forward through your playlist and - goes to the
previous song or restarts the current song.
Adjusting volume: To adjust volume you simply hold down
the + or - teeth and the volume will start to go up or
down. We recommend having the skull at max volume
and then adjusting volume using your music device. To
turn the skull to max volume simply hold down the + tooth
until you hear a tone.
Attaching strap
There is an indent in the top of the skull with a cap in it. If
you remove this cap there is a bar where the lanyard can
be tied to the skull and hung from wherever you please
M function button
The button on the back labeled “M” is the function button.
This is used for switching from Bluetooth to Aux to
memory card to USB. This button is also used for pairing
2 skulls. (See Pairing 2 skulls)
Pairing 2 skulls for stereo function
These skulls are equipped with dual pairing abilities so 2
can be paired for simultaneous playback. To pair 2 skulls,
power on both devices at same time. Then hold the M
function on one skull until they both make a pairing noise.
No other devices can be paired during this step.
Charging
To charge the device, power off and plug the charger into
the wall outlet. Place the device on the charger and allow
it to sit for a minimum of 1 hour. Do not charge for more
than 12 hours as this can damage the battery.
Warm prompt
1. In order to prolong the service life of the machine and
protect your physical and mental health, please don't
listen to music loudly for extended periods of time, so you
do not damage your hearing.
2. If the machine malfunctions, please immediately shut
off the power switch and unplug the USB cord to prevent
damage of the speaker and other components.
3. Electricity shortages affect bluetooth distance or cause
bluetooth to disconnect, please recharge in time.
Matters needing attention
1. Please store and use in normal temperature
environments.
2. Please do not expose the product to direct sun, rain or
damp environments.
3. Please do not throw or cause product damage.
4. Built-in lithium battery products, please do not discard
in normal trash or set on fire, this will cause danger.
5. Please do not alter the product itself.
FCC Statement
This equipment has been tested and found to comply
with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV
technician for help.
Caution: Any changes or modifications to this device not
explicitly approved by manufacturer could
void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF
exposure requirement. The device can be used in
portable exposure condition without restriction.
Bluetooth stereo button layout
128
1
Home Accents Holiday 1009025383 User manual
Lego 21320 Building Instruction
tayogo WB02 User manual
Nintendo 1.13 User manual
Disney Pirates of the Caribbean: At World's End NTR-AW3E-USA User manual
Jackson JS30RR Rhoads Quick start guide
Jarre AeroSkull User manual
Hasbro Native Americans Operating instructions
