2. ADO
  3. A16 Folding Electric Bike
A16 Folding Electric Bike

ADO A16 Folding Electric Bike Installation guide

  • Hello! I've reviewed the Quick Installation Guide for the A16, A20, and A20F ebikes. This document provides step-by-step instructions for assembling your new ebike, including how to install the foot brace, adjust the handlebars and saddle, and activate the battery. It also covers basic operation of the ebike interface. I'm ready to answer any questions you might have about the content of this guide.
  • How do I start the ebike?
    How do I shut down the ebike?
    How do I increase the gear?
    How do I decrease the gear?
ADO A16, A20, A20F, Ebike
Quick Installation Guide
1. Mobile Phone Stand 2. Pedals 3. Chargers 4. Foot support 5. Air Pump
6. 5mm Hexagon screw driver 7. 6mm Hexagon screw driver 8.Multi-type wrench
Accessories list
Installation Guide
Depending on the model, some steps have already been installed, just check it.
4. Fasten the safety lock
13 4 5 6 7 8
2
1
2
1. After opening the carton, take out the accessories, tools
and bicycle.
3. Close the body lock.
5. Prepare foot brace, use the tool to take out two
5mm hexagon screws locked in the foot brace.
6. Place the foot brace behind the fender, use the tool
to lock the screws.
2. Unroll the body
66
English
1
2
2
1
3
1
1
2
2
1
2
Mark lines
7. Place the head tube into the front fork head tube
9. Open the lock firstly.After alignment, put down the
tube, use the tool to lock the screws.
11. Open the handlebar lock, adjust the height of the head,
and then lock tightly.
13. Insert the saddle into the saddle tube. Adjust the height
of the saddle, and then lock tightly.
1. Align the left pedal ( with "L" mark ) to the crank thread
and rotate the pedal counterclockwise.
2. Align the right pedal ( with "R" mark ) to the crank
thread and rotate the pedal clockwise.
3. Tighten the pedals with an Hexagon screwdriver.
12. Open the cross handle lock, adjust the direction of the
head grip, and then lock tightly.
10. Put the tube up, close the head lock, snap the safety
lock into the head lock
8. Straighten the head and make sure that the arrow on
the label is aligned with the marking line. Make sure that
the bicycle head and the body are vertical to each other.
4 3
7
45°
90°
1
2
30°
45°
16. Finish the installation, use the pump to inflate the
tires.
15. Turn the headlight to the front 30 degrees down
positionuse the tool to twist the screws.
17. Before using the bicycle, insert the key and twist
45°counterclockwise, the battery has been started.
19.The step of removing battery, insert the key, press upward and then rotate 90°clockwise.
Note:Remove the key firstly,and then take out key and then take out the battery to avoid damaging the key.
18. Finished using the bicycle, turn the key 45°clockwise,
the battery has been disconnected, and take out the key.
8
1.In shutdown state, long press Power key for 3 second to start the ebike;
2.In the power on state, Long press Power key for 3 second to off the ebike;
3.In the power-on state, press POWER KEY, the multi-function area will display ODO, VOL, TRIP, TIME.
ODO: The total mileage of this bicycle when it is turned on
VOL: Current battery voltage value display
TRIP: Mileage traveled after this start
TIME: The time since the start of this ride
4. Press the “+” button to increase the gear. The higher the gear, the faster the speed.
5. Press the “-” button to lower the gear. The lower the gear, the slower the speed.
Switch on/off
Battery power display
Speed display
Assist gear display
Assist gear
adjustment
Multifunctional display area
SPEED
km/h
km
Operation Guide
3
/