Rain Harvesting HW0910 Installation guide

Brand: Rain Harvesting

Model: HW0910

Type: Installation guide

Rain Harvesting HW0910: Create secure T-junction cut-ins with this snap-on PVC junction suitable for 90mm pipes. Easily connect a 90mm branch/offtake to an existing 90mm pipe. For installation, use primer to clean the pipe and the inside of the junction, apply solvent weld glue, and hold the cradle over the pipe until secure. Use the appropriately sized hole saw to cut a hole in the pipe and install your branch/offtake pipe.

Code

Size

Country

HW0910

90mm

Australia

HW0911

90mm

HW0912

100mm

Easy Tee

Installation and Specification Guide

PRODUCT DETAILS

Easily create secure T-junction cut-ins with the

snap-on PVC Easy Tee Junction, suitable for

90mm and 100mm pipes.

rainharvesting.com

Installation

WHAT’S IN THE BOX? TOOLS/MATERIALS YOU MAY REQUIRE

Easy Tee Junction Priming fluid

Solvent weld glue

Drill

86mm hole saw or 102mm hole saw

EASY TEE

1 - Select your desired installation point. The Easy Tee Junction can be installed on vertical and horizontal

pipes.

2 - Use primer to clean the pipe around your chosen installation point and to clean the inside of your Easy

Tee “Snap on cradle” and branch/offtake socket.

3 - Apply solvent weld glue to the inside of your Easy Tee “Snap on cradle” and to the pipe of your

installation point, push the cradle over the pipe and hold in position for a minimum of 60 seconds or until

secure.

4 - Allow the solvent weld glue to dry.

5 - Using the appropriately sized hole saw and drill (86mm for 90mm and 102mm for 100mm) cut a hole in

the pipe through the branch/offtake socket of your Easy Tee Junction and install your 90mm or 100mm

branch/offtake pipe.

rainharvesting.com

PRODUCT SELECTION GUIDE

HW0910 (90mm X 90mm) – Allows you to connect a 90mm branch/off take

HW0911 (100mm x 90mm) – Allows you to connect a 90mm branch/offtake

HW0912 (100mm x 100mm) – Allows you to connect a 100mm branch/offtake

For an existing 90mm pipe:

For an existing 100mm pipe:

Easy Tee

Country

Code

Australia

HW0910

90 F

122

159

HW0911

90 F

100 F

139

159

HW0912

100 F

149

189

Product Specifications

Dimensions & Pipe Fittings

All dimensions are in mm unless otherwise stated.

rainharvesting.com

Fitting guide:

F = Female / Socket Fitting

M = Male / Spigot Fitting (Pipe size)

IP = In-Pipe Fitting

A common misconception about collecting rainwater is that all you need is a

roof, a tank and some rain. This ‘tanking’ approach cannot always be relied on to

deliver the volume – or quality – of water that you require. That is where we can

help.

With some thought, your rain harvesting system can provide you with cleaner

water and lots of it. Whether you’re completely reliant on tank water or wanting

to keep the garden green, our simple steps will help you achieve your goal.

The Rain Harvesting approach to rainwater collection involves using tested and

proven products to make quality rainwater available for use in and around your

property. You don’t need much to get started and you will be surprised how

easy it is to get the most out of your rainwater system.

How can we help you?

COMPLIANCE

Australian Standard AS/NZS 4020:2005

(Testing of products for use in contact with drinking water)

DISCLAIMER This product specification is not a complete guide to product usage. Further information is available from Rain Harvesting Pty Ltd and from the Installation and Operating

Instructions. This specification sheet must be read in conjunction with the Installation and Operating Instructions and all applicable statutory requirement. Product specifications may

rainharvesting.com

Maintenance